• Journal of the Korean Magnetics Society
• /
• v.7 no.6
• /
• pp.299-307
• /
• 1997

NdFeB films have been grown onto Si(100) substrate by a KrF pulsed laser ablation of the targets of $Nd_xFe_{90.98-x}B_{9.02}$ (x=17.51~27.51) at the substrate temperature of 620~700 $^{\circ}C$ and the laser beam energy density of 2.75~5.99 J/$\textrm{cm}^2$. The films exhibit no preferred orientation, however, good hard magnetic properties were produced from as-deposited condition : $4{\pi}M_s$=7 kG, $4{\pi}M_r$=4 kG, and $H_c$=300~1000 Oe. The depositon rate was not greatly influenced by changing the substrate temperature, but it increases linearly by increasing the beam energy density. The beam energy density of 3 J/$\textrm{cm}^2$ gave the optimal condition to have the highest $4{\pi}M_r$ and $H_c$ as well. The higher content of Nd induces a higher coercivity and $4{\pi}M_r$ at the same time without prominent change in $4{\pi}M_s$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.240.1-240.1
• /
• 2011

본 연구에서는 펄스레이져 박막 증착법(Pulsed Laser Deposition;PLD)을 이용하여 연자성의 CoNiFe (CNF) 물질과 강유전 특성의$BaTiO_3$ (BTO) 물질을 다층박막 구조로 제작하여 약자장(H=200 Oe)에 의해 에너지를 집적 시키거나 유전상수를 조절하여 박막의 구조 변화에 따른 커패시턴스 변화를 연구하였다. 다양한 구조의 다층 박막은 Si/$SiO_2$/Ti/Pt(111) 기판상에 PLD을 이용하여 증착하였으며, Phillp's X-선 회절기 (XRD)를 이용하여 결정구조와 격자 상수를 결정하였다. FE-SEM, TEM, AFM 및 EDS를 이용하여 박막 표면/단면의 미세구조 및 물질에 따른 조성비를 확인하였다. 자기적 특성을 위해Vibrating Sample Magnetometer (VSM)를 측정하였고, 전기적 특성은 LCR meter를 이용하여 측정하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.05a
• /
• pp.99-101
• /
• 1996

This paper is concerned with the fabrication of (Fe,Co)-Si-B amorphous magneto-strictive wire which attracts strong attention as a new sensor material. First, we put the ingot of (Fe$\sub$1-x/Co$\sub$x/)$\sub$77/Si$\sub$8/B$\sub$15/ composition into quartz tube. Then, under the condition of 400MHz and 8kW, we melt and mix the in-got in the high frequency induction furnance. After that, we obtain the magnetostrictive wire of 100∼150$\mu\textrm{m}$ in diameter by injection and rapid quenching within the high rotating water. Finally, we find that the wire is under the amorphous state.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04b
• /
• pp.3-6
• /
• 2009

Aluminum nitride (AIN) thin films were deposited on a polycrystalline 3C-SiC intermediate layer by a pulsed reactive magnetron sputtering system. Characteristics of the AIN/SiC heterostructures were investigated by field emission scanning electron microscopy (FE-SEM), atomic force microscopy (AFM), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FT-IR). The columnar structure of AIN thin films was observed by FE-SEM. The surface roughness of AlN films on the 3C-SiC buffer layer was measured using AFM. The XRD pattern of AlN films on SiC buffer layers was highly oriented at (002). Full width at half maximum (FWHM) of the rocking curve near (002) reflections was $1.3^{\circ}$. The infrared absorbance spectrum indicated that the residual stress of AIN thin films grown on SiC buffer layers was nearly negligible. The 3C-SiC intermediate layers are promising for the realization of nitride based electronic and mechanical devices.

• Journal of the Korean institute of surface engineering
• /
• v.20 no.4
• /
• pp.144-153
• /
• 1987

In the case of dipping the Ni-Resist cast iron into molten aluminum with iron content, the thickness of intermetallic compound was remarkably increased with increasing iron content. The thickness was shown by following equation in the range of 1-3% iron content; $x=22.5t^{1/2}+4.47{\cdot}t{\cdot}(Fe%)$. where, x is thickness(${\mu}m$), t the time (minute), Fe% the iron w/o. When the Ni-Resist cast iron was dipped into the molten aluminum containing zinc content, the intermetallic compound thickness was also increased with increasing zinc contents. And thickness was represented by the following equation in the range of 2-10% zinc content; $x=3.46t^{1/2}+0.27{\cdot}t{\cdot}(Zn%)$. However, in the case of dipping the Ni-resist cast iron into molten aluminum with silicon content, the thickness of intermetallic compound was decreased with increasing silicon content, as shown in the following equation; $x=7.17t^{1/2}-0.15{\cdot}t{\cdot}(Si%)$. The intermetallic compound formed onto Ni-Resist cast iron was identified to be $FeAl_3\;and\;Fe_3Al$. As the result of hardness measurement, the peak hardness appeared in the intermetallic compound at near interface of the cast iron and the compound.

• Korean Chemical Engineering Research
• /
• v.48 no.3
• /
• pp.304-310
• /
• 2010

The FTS(Fischer-Tropsch synthesis) was carried out over precipitated iron-based catalysts with or without $SiO_2$ in a fixed-bed reactor at $250^{\circ}C$ and 1.5 MPa. The catalysts with $SiO_2$ showed much higher catalytic activity for the FTS than those without $SiO_2$, displaying excellent stability during 144 h of reaction. The X-ray diffraction and $N_2$ physisorption revealed that the catalysts with $SiO_2$ showed enhanced dispersion of $Fe_2O_3$ compared with those without $SiO_2$. Also, the results of temperature-programmed reduction by $H_2$ showed that the addition of $SiO_2$ markedly promoted the reduction of $Fe_2O_3$ into $Fe_3O_4$ and FeO at low temperatures below $260^{\circ}C$. In contrast, surface basicity of the catalysts, which was analyzed by temperature-programmed desorption of $CO_2$, decreased as a result of $SiO_2$ addition. We attribute the high and stable performance of the catalysts with $SiO_2$ to the improved dispersion and reducibility by the $SiO_2$ addition.

• Journal of the Korean Society for Heat Treatment
• /
• v.37 no.3
• /
• pp.121-127
• /
• 2024

We investigate the effect of T6 heat treatment on the microstructure and mechanical properties of AA365 (Al-10.3Si-0.37Mg-0.6Mn-0.11Fe, wt.%) alloy fabricated by vacuum-assisted high pressure die casting by means of thermodynamic calculation, X-ray diffraction, scanning and transmission electron microscopy, and tensile tests. The as-cast alloy consists of primary Al (with dendrite arm spacing of 10~15 ㎛), needle-like eutectic Si, and blocky α-AlFeMnSi phases. The solution treatment at 490 ℃ induces the spheroidization of eutectic Si and increase in the fraction of eutectic Si and α-AlFeMnSi phases. While as-cast alloy does not contain nano-sized precipitates, the T6-treated alloy contains fine β' and β' precipitates less than 20 nm that formed during aging at 190℃. T6 heat treatment improves the yield strength from 165 to 186 MPa due to the strengthening effect of β' and β' precipitates. However, the β' and β' precipitates reduce the strain hardening rate and accelerate the necking phenomenon, degrading the tensile strength (from 290 to 244 MPa) and fracture elongation (from 6.6 to 5.0%). Fractography reveals that the coarse α-AlFeMnSi and eutectic Si phases act as crack sites in both the as-cast and T6 treated alloys.

• Journal of the Korean institute of surface engineering
• /
• v.30 no.4
• /
• pp.248-254
• /
• 1997

The sulfidation behavior of a sputter-deposited amorphous coating of 69.0%Nb-16.9Ni-11.9%Al-2.2%Si (at.%) has been investigated as a funtion of temperature.(973-1173K) in pure sulfur pressure of 0.01atm. The sulfidation kinetics of the casting obyed the parabolic rate low over the whole temperature ranges studied. The stlfidation rate increased with the temperature, as expected. The sulfide scale, the composition of which was $Al_2S_3,\;NbS_2,\;Ni_{3-x}S_2\;and\;FeCrS_4$, formed on the amorphous coating was primarily bilayered. Both the outer fastgrowing non-protective 4Al_2S_3$scale and the inner slowly-growing protective $NbS_2$,/TEX> scale and the inner slowly-growing protective $NbS_2$ scale had some Fe and Cr dissolution, which evidently came from the base substrate alloy of stainless steel type 304. Belows the coating, Kirkendall void formation was noticed. Nevertheless, a dramatic improvement of sulfidation resistance was achieved by sputter-depositing Nb-2 Ni-Al-Si layer on the stainless steel 304.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2007.12a
• /
• pp.64-66
• /
• 2007

• Economic and Environmental Geology
• /
• v.42 no.6
• /
• pp.549-559
• /
• 2009

The objectives of this study are to investigate the biomineralization of goethite and lepidocrocite formed on the twisted-stalk and the sheathed-filament structure that is suggest microbe origin, and heavy metal in the yellow Fe-hydroxide. On the ratio of Cl and the Cl/Br ratios that are a pollution and non-pollution of groundwaters, it is indicated that the groundwater in this areas were relatively contaminated by human activity. The composition of the yellow Fe-hydroxide consisted mainly of $Fe_2O_3$ and $SiO_2$. The content of $Fe_2O_3$ ranges from 58.57 wt.% to 75.7 3wt.%, and $SiO_2$ content ranges from 5.8 wt.% to 16.17 wt.%. Heavy metal elements such as Zn(max. 6,160 mg/kg), Pb(max. 377 mg/kg), U(max. 503 mg/kg), Cr(max. 203 mg/kg), Cu(max. 77 mg/kg), V(max. 162 mg/kg), Ni(max. 105 mg/kg) were observed to be rich in those yellow Fe-hydroxide. The lath and platy crystals and needle-shaped crystals were clearly observed on the twisted-stalks and sheathed-filaments structure. The goethite, gypsum, and lepidocrocite were identified in the yellow Fe-hydroxide by x-ray powder diffraction.