• Journal of Korean Society of Water and Wastewater
• /
• v.34 no.1
• /
• pp.45-52
• /
• 2020

Even though sewers have been conventionally designed to prevent from sediment deposition using a specified minimum velocity or shear stress at a particular depth of flow or with a particular frequency of occurrence, it was appreciated that these methods do not consider the characteristics and concentration of the sediment and the specific hydraulic conditions of the sewer with sediment. In this study, a densimetric Froude number formula was suggested considering particle diameter and volumetric concentration of the sediment as well as flow depth and flowrate, based on several domestic field inspections, which was compared with other formulas proposed by previous investigators. When the sediment concentration was not considered, the calibration coefficient of 0.125-1.5 to the densimetric Froude numbers of this study was needed to obtain the similar ones with previous investigators'. For the densimetric Froude number formula obtained with consideration of sediment concentration, the exponent value of term C_v was almost the same as that of previous results and that of d₅₀/R_h was similar for F_r < 2.2.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.283.2-283.2
• /
• 2013

The variation of chemical and interfacial state during the growth of Ta2O5 films on the Si substrate by atomic layer deposition (ALD) was investigated using in-situ synchrotron radiation photoemission spectroscopy. A newly synthesized liquid precursor Ta(NtBu)(dmamp)2Me was used as the metal precursor, with Ar as a purging gas and H2O as the oxidant source. The core-level spectra of Si 2p, Ta 4f, and O 1s revealed that Ta suboxide and Si dioxide were formed at the initial stages of Ta2O5 growth. However, the Ta suboxide states almost disappeared as the ALD cycles progressed. Consequently, the Ta5+ state, which corresponds with the stoichiometric Ta2O5, only appeared after 4.0 cycles. Additionally, tantalum silicate was not detected at the interfacial states between Ta2O5 and Si. The measured valence band offset value between Ta2O5 and the Si substrate was 3.08 eV after 2.5 cycles.

• Journal of Marine Bioscience and Biotechnology
• /
• v.11 no.1
• /
• pp.14-22
• /
• 2019

Omega-3 fatty acids and carotenoids, which are known as representative high-value substances derived from microalgae, are being studied from various diatoms. Most of the diatoms contain fucoxanthin and omega-3 fatty acid. Fucoxanthin produced by diatom has been reported as bioactive compounds exhibiting strong antioxidant, anticancer and anti-inflammatory activities. However, the low growth rate and fucoxanthin content of diatoms are one of the big obstacles to the industrial application. In this study, indigenous marine diatom Achnanthidium sp. BS-001 was isolated for a candidate of fucoxanthin producer. Light intensity and temperature for the culture of Achnanthidium sp. BS-001 were optimized on PhotoBiobox. Optimization of silicate concentration for increasing BS-001 biomass productivity was confirmed in F/2 medium with various concentration of sodium silicate. As a result, condition of light intensity, temperature, and silicate concentration for optimal cultivation were $150{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$, $18^{\circ}C$ and 0.106 mM, respectively. Maximum biomass productivity reaches to $154.3mg{\cdot}L^{-1}{\cdot}day^{-1}$, and then the content of omega-3 fatty acids and fucoxanthin were $19.4mg{\cdot}g^{-1}$, $9.05mg{\cdot}g^{-1}$, respectively. These results indicate that Achnanthidium sp. BS-001 has the potential to be used as a source of omega-3 fatty acids and fucoxanthin.

• Journal of radiological science and technology
• /
• v.44 no.6
• /
• pp.635-643
• /
• 2021

The results of empirical researches on the diagnosis of lung cancer are insufficient, so it is limited to objectively judge the clinical possibility and utilization according to the accuracy of diagnosis. Thus, this study retrospectively analyzed the lung cancer diagnostic performance of PET-MRI (Positron Emission Tomography-Magnetic Resonance Imaging) by using the decision matrix. This study selected and experimented total 165 patients who received both hematological CEA (Carcinoembryonic Antigen) test and hybrid PET-MRI (¹⁸F-FDG, 5.18 MBq/kg / Body TIM coil. VIVE-Dixon). After setting up the result of CEA (positive:>4 ㎍/ℓ. negative:<2.5㎍/ℓ) as golden data, the lung cancer was found in the image of PET-MRI, and then the SUV_max (positive:>4, negative:<1.5) was measured, and then evaluated the correlation and significance of results of relative diagnostic performance of PET-MRI compared to CEA through the statistical verification (t-test, P>0.05). Through this, the PET-MRI was analyzed as 96.29% of sensitivity, 95.23% of specificity, 3.70% of false negative rate, 4.76% of false positive rate, and 95.75% of accuracy. The false negative rate was 1.06% lower than the false positive rate. The PET-MRI that significant accuracy of diagnosis through high sensitivity and specificity, and low false negative rate and false positive rate of lung cancer, could acquire the fusion image of specialized soft tissue by combining the radio-pharmaceuticals with various sequences, so its clinical value and usefulness are regarded as latently sufficient.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.4
• /
• pp.72-77
• /
• 2021

The radial distribution of etch rate was analyzed using the ion energy flux model in VHF-CCP. In order to exclude the effects of polymer passivation and F radical depletion on the etching. The experiment was performed in Ar/SF6 plasma with an SF6 molar ratio of 80% of operating pressure 10 and 20 mTorr. The radial distribution of Ar/SF6 plasma was diagnosed with RF compensated Langmuir Probe(cLP) and Retarding Field Energy Analyzer(RFEA). The radial distribution of ion energy flux was calculated with Bohm current times the sheath voltage which is determined by the potential difference between the plasma space potential (measured by cLP) and the surface floating potential (by RFEA). To analyze the etch rate uniformity, Si coupon samples were etched under the same condition. The ion energy flux and the etch rate show a close correlation of more than 0.94 of R² value. It means that the etch rate distribution is explained by the ion energy flux.

• Structural Engineering and Mechanics
• /
• v.82 no.1
• /
• pp.121-131
• /
• 2022

The main goal of this study is to prepare a program for analyzing High Strength Steel Fibrous Reinforced Concrete (HSSFRC) slabs and predict the response and strength of the slab instead of preparing a prototype and testing it in the laboratory. For this purpose, new equations are proposed to represent the material properties of High Strength Steel Fibrous Reinforced Concrete. The proposed equations obtained from performing regression analysis on many experimental results using statistical programs. The finite element method is adopted for non-linear analysis of the slabs. The eight-node "Serendipity element" (3 DoF) is chosen to represent the concrete. The layered approach is adopted for concrete elements and the steel reinforcement is represented by a smeared layer. The compression properties of the concrete are modeled by a work hardening plasticity approach and the yield condition is determined depending on the first two stress invariants. A tensile strength criterion is adopted in order to estimate the cracks propagation. many experimental results for testing slabs are compared with the numerical results of the present study and a good agreement is achieved regarding load-deflection curves and crack pattern. The response of the load deflection curve is slightly stiff at the beginning because the creep effect is not considered in this study and for assuming perfect bond between the steel reinforcement and the concrete, however, a great agreement is achieved between the ultimate load from the present study and experimental results. For the models of the tension stiffening and cracked shear modulus, the value of Bg and Bt (Where Bg and Bt are the curvature factor for the cracked shear modulus and tension stiffening models respectively) equal to 0.005 give good results compared with experimental result.

• The Korea Journal of Herbology
• /
• v.24 no.3
• /
• pp.13-19
• /
• 2009

Objectives : This study was aimed to define the protective effect of Tissue Cultured Root of Wild Ginseng (CWG) against doxorubicin (Doxo) toxicity, and investigate the anti-tumor synergic effect of CWG in combination with Doxo in tumor-bearing C57BL/6 mice. Methods : Tumor-bearing mice were established by single inoculation with B16/F10 melanoma cells (2$\times$10$^6$/ml) subcutaneously. Tumor-bearing mice (tumor volume between 50-100 mm$^3$) were selected and divided them into control, Doxo, and Doxo+CWG group. Mice of Doxo group were received with Doxo (4 mg/kg of B.W.) intraperitoneally at 0, 4, 8 days after starting the experiment. Mice of Doxo+CWG group were received CWG water extract during 12 days in combination with Doxo treatment. The body weight, tumor volume, tumor weight, and organ weight (heart, liver, kidney, and testis) were measured. And serum SPK, GOT and creatinine values were analysed. Results : The volume and weights of tumor masses in Doxo group were decreased significantly compared with the those of control group. And the those of Doxo+CWG group were not significantly different from the those of Doxo group. Whereas the weight of body, liver, kidney and testis in Doxo+CWG group were increased significantly compared with the those of Doxo group. The level of serum CPK and GOT in Doxo group were increased compared with the those of control group. But the value of Doxo+CWG group were decreased significantly compared with the values of Doxo group. Conclusions : These results suggest that CWG has protective effect against doxorubicin toxicity. And these effect is guessed that is caused in augmentation of vital energy.

• Structural Monitoring and Maintenance
• /
• v.10 no.1
• /
• pp.87-105
• /
• 2023

Seismic regulations have been updated from time to time to accommodate an increase in seismic hazards. Comparison of seismic fragility of the existing bridges in Indonesia from different historical periods since the era before 1990 will be the basis for seismic assessment of the bridge stock in Indonesia, most of which are located in earthquake-prone areas, especially those built many years ago with outdated regulations. In this study, seismic fragility curves were developed using incremental non-linear time history analysis and more holistically according to the actual strength of concrete and steel material in Indonesia to determine the uncertainty factor of structural capacity, βc. From the research that has been carried out, based on the current seismic load in SNI 2833:2016/Seismic Map 2017 (7% probability of exceedance in 75 years), the performance level of the bridge in the era before SNI 2833:2016 was Operational-Life Safety whereas the performance level of the bridge designed with SNI 2833:2016 was Elastic - Operational. The potential for more severe damage occurs in greater earthquake intensity. Collapse condition occurs at As = F_PGA x PGA value of bridge Era I = 0.93 g; Era II = 1.03 g; Era III = 1.22 g; Era IV = 1.54 g. Furthermore, the fragility analysis was also developed with geometric variations in the same bridge class to see the effect of these variations on the fragility, which is the basis for making bridge risk maps in Indonesia.

• Wind and Structures
• /
• v.37 no.6
• /
• pp.425-444
• /
• 2023

This study is to investigate the effect of interference between two C-shaped high-rise buildings by computational fluid dynamics (CFD), focusing on the variation of the local pressure coefficient (C_P) and the mean pressure coefficient (C_PMEAN). Sixteen building position cases are considered for the present study. These cases were based on the position and height of the interference building (IB). The pressure coefficient (C_P) is calculated on the principal building (PB) and is compared with an isolated building identical in shape and size. The interference effect on PB has also been presented in reference for the interference factor (IF). According to the findings, the maximum force coefficient on the PB is 0.971 and it is 10.97% more than the isolated PB when IB is located at position 2b (two times the width of the building), and the interfering height of 13H/15 mm. The moment coefficient on PB is 1.27, which is 27.36% less than the isolated case in which IB pushed 2b to 3b in the y direction with 750 mm height. In most of the cases, because of the shielding effect of the IB, the value of force coefficient (C_F) on PB has been reduced. On the face of the PB, there are also considerable differences in the mean pressure coefficient C_PMEAN. When IB was positioned at a location of 2b in Y direction and an interfering height of 13H/15 mm, the maximum C_PMEAN (1.58) was observed on the leeward face of PB.

• Tuberculosis and Respiratory Diseases
• /
• v.58 no.6
• /
• pp.562-569
• /
• 2005

Background : The severity scoring system is useful for predicting the outcome of critically ill patients. However, the system is quite complicated and cost-ineffective. Simple serologic markers have been proposed to predict the outcome, which include troponin-I, lactate and C-reactive protein(CRP). The aim of this study was to evaluate the prognostic values of troponin-I, lactate and CRP in critically ill non-cardiac patients. Methods : From September 2003 to June 2004, 139 patients(Age: $63.3{\pm}14.7$, M:F = 88:51), who were admitted to the MICU with non-cardiac critical illness at Gyeongsang National University Hospital, were enrolled in this study. This study evaluated the severity of the illness and the multi-organ failure score (Acute Physiologic and Chronic Health EvaluationII, Simplified Acute Physiologic ScoreII and Sequential Organ Failure Assessment) and measured the troponin-I, lactate and CRP within 24 hours after admission in the MICU. Each value in the survivors and non-survivors was compared at the 10th and 30th day after ICU admission. The mortality rate was compared at 10th and 30th day in normal and abnormal group. In addition, the correlations between each value and the severity score were assessed. Results : There were significantly higher troponin-I and CRP levels, not lactate, in the non-survivors than in the survivors at 10th day($1.018{\pm}2.58ng/ml$, $98.48{\pm}69.24mg/L$ vs. $4.208{\pm}10.23ng/ml$, $137.69{\pm}70.18mg/L$) (p<0.05). There were significantly higher troponin-I, lactate and CRP levels in the non-survivors than in the survivors on the 30th day ($0.99{\pm}2.66ng/ml$, $8.02{\pm}9.54ng/dl$, $96.87{\pm}68.83mg/L$ vs. $3.36{\pm}8.74ng/ml$, $15.42{\pm}20.57ng/dl$, $131.28{\pm}71.23mg/L$) (p<0.05). The mortality rate was significantly higher in the abnormal group of troponin-I, lactate and CRP than in the normal group of troponin-I, lactate and CRP at 10th day(28.1%, 31.6%, 18.9% vs. 11.0%, 15.8 %, 0%) and 30th day(38.6%, 47.4%, 25.8% vs. 15.9%, 21.7%, 14.3%) (p<0.05). Troponin-I and lactate were significantly correlated with the SAPS II score($r^2=0.254$, 0.365, p<0.05). Conclusion : Measuring the troponin-I, lactate and CRP levels upon admission may be useful for predicting the outcome of critically ill non-cardiac patients.