• Journal of the Korean Ceramic Society
• /
• v.32 no.11
• /
• pp.1219-1226
• /
• 1995

Creep behaviors of Cr3C2 composites containing 90 wt% Cr3C2 and 10 wt% Ni were studied at high temperature. Compression tests at 100$0^{\circ}C$ and bending tests at 100$0^{\circ}C$ and 105$0^{\circ}C$ were done in argon environment. In all test conditions primary and steady-state creep behaviors were observed. Stress exponent and activatiion energy were determined from the experimental data. By microstructural analysis of Cr3C2 composites after creep test, the separate agglomerations of Ni phase were observed. Numerical analysis was also studied to analyze bending creep behaviors of Cr3C2 by assumming different tensile and compressive creep behavior in a bending sample. From the analysis, it was found that the stress state at the compressive region as applied stress increased. The observed creep rates were compared with the predicted creep rates by estimating power-law creep parameters from bending test data.

• Journal of Sensor Science and Technology
• /
• v.13 no.6
• /
• pp.424-429
• /
• 2004

$Cr_{2}O_{3}$ thick films were fabricated by screen printing method on alumina substrates and annealed at $700^{\circ}C$, $800^{\circ}C$, and $900^{\circ}C$ in air, respectively. Structural properties examined by XRD and SEM showed (116) dominant $Cr_{2}O_{3}$ peak and increased grain sizes with the annealing. The resistance of the films decreased with increasing the annealing temperature. Gas sensing characteristics to $NH_{3}$, CO, $C_{4}H_{10}$, and NO gases showed sensitivity only to $NH_{3}$ gas. $Cr_{2}O_{3}$ thick films annealed at $700^{\circ}C$ had the sensitivity of about 15 % for 100 ppm $NH_{3}$ gas at the working temperature of $300^{\circ}C$. The thick films had good selectivity to the $NH_{3}$ gas. The response time to $NH_{3}$ gas was about 10 seconds.

• Journal of the Korean Ceramic Society
• /
• v.45 no.5
• /
• pp.268-275
• /
• 2008

In high temperature ceramic glazes, a stable range of pink-red colors producing $Cr_2O_3-SnO_2-CaO-SiO_2$ pigments are factored by Cassiterite and Malayaite relationship with $Cr_2O_3$. The experiment described the effect of $CrCl_3$ by adding $H_3BO_3$ as a mineralizer to increase the formation of Malayaite crystal, substituting $CrCl_3$ instead of $Cr_2O_3$ in pigment as a chromophore. Synthesized pigments were analyzed by XRD, FT-IR, Raman Spectroscop, UV and UV-vis. The result shows the differences in amount of crystal phases and oxidation state of Cr ion, which causes the color change. The melting point of $CrCl_3$ is lower than $Cr_2O_3$ which act as a mineralizer and makes the pigment synthesized in lower temperature at $1200^{\circ}C$. Holding 3 h firing at $900^{\circ}C$ where the synthesize forms shows better effect of Malayaite crystal phases and increasing engaged effect of $CrCl_3$ where the color pigmentation is more defined then in $Cr_2O_3$.

• Applied Chemistry for Engineering
• /
• v.17 no.5
• /
• pp.451-457
• /
• 2006

We synthesized phase pure CrN having surface areas up to $47m^2/g$ starting from $CrCl_{3}$ with $NH_{3}$. Thermal Gravimetric Analysis coupled with X-ray diffraction was carried out to identify solid state transition temperatures and the phase after each transition. In addition, the BET surface areas, pore size distributions, and crystalline diameters for the synthesized materials were analyzed. Space velocity influenced a little to the surface areas of the prepared materials, while heating rate did not. We believe it is due to the fast removal of reaction by-products from the system. Temperature programmed reduction results revealed that the CrN was hardly passivated by 1% $O_{2}$. Molecular nitrogen was detected from CrN at 700 and $950^{\circ}C$, which may be from lattice nitrogen. In temperature programmed oxidation with heating rate of 10 K/min in flowing air, oxidation started at or higher than $300^{\circ}C$ and resulting $Cr_{2}O_{3}$ phase was observed with XRD at around $800^{\circ}C$. However the oxidation was not completed even at $900^{\circ}C$. CrN catalysts were highly active for n-butane dehydrogenation reaction. Their activity is even higher than that of a commercial $Pt-Sn/Al_{2}O_{3}$ dehydrogenation catalyst in terms of volumetric reaction rate. However, CrN was not active in pyridine hydrodenitrogenation.

• Journal of the Korean Chemical Society
• /
• v.34 no.6
• /
• pp.534-538
• /
• 1990

Chromium(Ⅵ) compound, [$C_9H_7$NH]$_2Cr_2O_7$ has been prepared by the reaction of isoquinoline with chromium trioxide under the presence of water. [$C_9H_7$NH]$_2Cr_2O_7$ is nonhydroscopic and dissolved in water very well. Structure of [$C_9H_7$NH]$_2Cr_2O_7$ is identified by FTIR spectra and elemental analysis data. The ability of [$C_9H_7$NH]$_2Cr_2O_7$ for the oxidation of alcohols were examined in methylene chloride. [$C_9H_7$NH]$_2Cr_2O_7$ was found as efficient oxidizing agent for the conversion of allyl, primary and secondary alcohols to the corresponding aldehydes or ketones.

• Bulletin of the Korean Chemical Society
• /
• v.14 no.6
• /
• pp.669-673
• /
• 1993

The CO substitution reactions of the complex, $Cp(S-2,4-Me_2C_5H_5)CrCo$ with $PR_3(PR_3=PMePh_2,\;P(OCH_3)_3,\;PMe_2Ph)$ were investigated spectrophotometrically at various temperatures. From the reaction rates, it was suggested that the CO substitution reaction took place by first-order (dissociative) pathway. Activation parameters in decaline were ${\Delta}H^{\neq}\;=\;22.0\;kcal{\cdot}mol^{-1}$, ${\Delta}S^{\neq}=\;-3.8cal{\cdot}mol^{-1}{\cdot}K^{-1}$. Unusually low value of ${\Delta}S{\neq}$ suggests an ${\eta}^5-S{\to}{\eta}^5-U$ conversion of the pentadienyl ligand. This suggestion was confirmed by the Extended-Huckel molecular orbital (EHMO) calculations, which revealed that the total energy of $Cp(S-2,4-Me_2C_5H_5$)CrCO is about 0.42 kcal/mol more lower than that of $Cp(U-2,4-Me_2C_5H_5)CrCO$ and the energy of $[Cp(U-2,4-Me_2C_5H_5)Cr{\cdots}CO]^{\neq} $ transition state is about 2.43 kcal/mol lower than that of $[Cp(S-2,4-Me_2C_5H_5)Cr{\cdots}CO]^{\neq}$ transition state.

• Korean Journal of Metals and Materials
• /
• v.50 no.1
• /
• pp.1-7
• /
• 2012

The fracture resistance and tensile properties of $Y_2O_3$ oxide dispersion strengthened steel containing 9 wt% Cr(9Cr-ODS) were measured at various temperatures up to $700^{\circ}C$. The fracture characteristics were compared with those of commercial E911 ferritic/martensitic steel. The strength of 9Cr-ODS was at least 30% higher than that of E911 steel at the test temperatures below $500^{\circ}C$. The strength difference between the two materials was almost diminished at $700^{\circ}C$. 9Cr-ODS showed cleavage fracture behavior at room temperature and unstable crack growth behaviors at $300^{\circ}C$ and $500^{\circ}C$. The J-R fracture resistance of 9Cr-ODS was much lower than that of E911 steel at all temperatures. It was deduced that the coarse $Cr_2O_3$ particles that were formed during the alloying process provided the crack initiation sites of cleavage fracture in 9Cr-ODS.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.952-955
• /
• 2002

$WC-3%(Cr_3C_2)-2%(Mo_2C)-12%Ni$ carbides were ground with three different types of electroplated diamond wheels with respect to grain friability. The grinding ratio in the case of the highest toughness grains, A becomes the highest at the workpiece speeds of 40 and 70mm/min exhibiting larger effect with smaller workpiece speed. The grinding ratio with the medium toughness grain is higher than that of grain A at higher workpiece speeds than 100mm/min. The surface roughness becomes smaller with increasing the grain friability The increasing rate on surface roughness with the increase of workpiece speed becomes higher with using the grain of lower friability.

• Journal of Welding and Joining
• /
• v.15 no.1
• /
• pp.125-134
• /
• 1997

This study was conducted by L9 orthogonal array to obtain optimum spray parameters for This study was conducted by L9 orthogonal array to obtain optimum spray parameters for $Cr_3C_2 - 7wt%$(80wt%Ni-20wt%Cr) coating powder. The factors were hydrogen flow rate, oxygen flow rate, gun-to-work distance, powder feed rate. And evaluation methods for the coating were surface roughness, oxygen concentration, micro-hardness, pore size and distribution, low angle ($30^{\circ}$) erosion rate, and microstructure of coating. The optimum HVOF spray conditions were proved as follows : hydroen flow rate ; 681 SLPM, oxygen flow rate ; 215 SLPM $H^2/O^2 ratio= 3.16), gun-to-work distance ; 22cm, powder feed rate; 25g/min. The hardness (Hv300) was 1147 and the erosion rate ($30^{\circ}$degree) was $3.16\times10^{-4}$g/g. It is believed that the optimized spray conditions can be improved the wear-resistance and anti-erosion characteristics of the coating.

• Journal of the Korean institute of surface engineering
• /
• v.22 no.1
• /
• pp.10-16
• /
• 1989

The properties of carburization on Fe-Cr alloys at 900-96$0^{\circ}C$were investiged. The study on carbide layer which had developed during solid-carburizing was made by use of S.E.M, E.PM.A, and X-ray analyzer. The results obtained were summarized as follows, the composition of carbide and the value of activation energy for the growth of carbide layer on each Fe-Cr alloy were 1) Fe-1Cr : M3C and 52Kcal/mole 2) Fe-3Cr and Fe-5Cr : M7C3and 85-88Kcal/mole 3) Fe-7Cr and Fe-9Cr : (M7C3+M23C6)and 55-66Kcal/mole.