• 한국재료학회지
• /
• 제20권5호
• /
• pp.241-245
• /
• 2010

One of the weak points of the Cr-doped SZO is that until now, it has only been fabricated on perovskite substrates, whereas NiO-ReRAM devices have already been deposited on Si substrates. The fabrication of RAM devices on Si substrates is important for commercialization because conventional electronics are based mainly on silicon materials. Cr-doped ReRAM will find a wide range of applications in embedded systems or conventional memory device manufacturing processes if it can be fabricated on Si substrates. For application of the commercial memory device, Cr-doped $SrZrO_3$ perovskite thin films were deposited on a $SrRuO_3$ bottom electrode/Si(100)substrate using pulsed laser deposition. XRD peaks corresponding to the (112), (004) and (132) planes of both the SZO and SRO were observed with the highest intensity along the (112) direction. The positions of the SZO grains matched those of the SRO grains. A well-controlled interface between the $SrZrO_3$:Cr perovskite and the $SrRuO_3$ bottom electrode were fabricated, so that good resistive switching behavior was observed with an on/off ratio higher than $10^2$. A pulse test showed the switching behavior of the Pt/$SrZrO_3:Cr/SrRuO^3$ device under a pulse of 10 kHz for $10^4$ cycles. The resistive switching memory devices made of the Cr-doped $SrZrO_3$ thin films deposited on Si substrates are expected to be more compatible with conventional Si-based electronics.

• 한국환경보건학회지
• /
• 제29권1호
• /
• pp.62-66
• /
• 2003

The biological denitrification batch tests were conducted to optimize the operating conditions with various temperature and initial SCO $D_{Cr}$ /N $O_3$-N ratio. and the denitrification rates were analyzed various SCO $D_{Cr}$ /N $o_3$-N ratio of influent with swine wastes fermented and temperature. The finishing time of denitrification was within 15 hours, 12 hours, and 6 hours as the temperature of denitrification applied were 15$\pm$1$^{\circ}C$, 25$\pm$1$^{\circ}C$, and 31$\pm$1$^{\circ}C$, respectively. From the batch tests, denitrification rate was operated with over 3 of SCO $D_{Cr}$ /N $O_3$-N ratio. Denitrification rate was increased as the temperature of denitrification, increased such as 2.40-3.90 mg N $O_3$-N/gMLVSSㆍhr, 6.10-7.60 mgN $O_3$-N/gMLVSSㆍhr, and 14.40-15.88 mgN $O_3$-N/gMLVSSㆍhr, respectively. The denitrification rate was increased as the ratio of initial SCO $D_{Cr}$ N $O_3$-N increased. However, it was found that the suitable ratio of SCO $D_{Cr}$ /N $O_3$-N for denitrification should be considered because the ratio of mg SCO $D_{Cr}$ , consumed per mg N $O_3$-N removed varied depend on the influent SCO $D_{Cr}$ /TKN ratios.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2001년도 추계학술발표회 초록집
• /
• pp.57-59
• /
• 2001

• 광물과 암석
• /
• 제33권2호
• /
• pp.115-127
• /
• 2020

운산 금 광상은 한반도의 3대(대유동 광상, 광양 광상) 금 광상중의 하나이었다. 이 광상 주변지질은 선캠브리아기의 변성퇴적암류와 중생대의 반상화강암으로 구성된다. 이 광상은 선캠브리아기의 변성퇴적암류와 중생대의 반상화강암내에 발달된 단층대를 따라 충진한 함 금 석영맥 광상으로 조산형 금 광상에 해당된다. 이 광상의 석영맥은 광물조합에 따라 1)방연석-석영맥형, 2)자류철석-석영맥형, 3)황철석-석영맥형, 4)페크마틱 석영맥형, 5)백운모-석영맥형 및 6)단순석영맥형으로 분류된다. 연구된 석영맥은 황철석-석영맥형이며 견운모화작용, 녹니석화작용 및 규화작용이 관찰된다. 이 석영맥은 백색 석영, 백색 운모, 녹니석, 황철석, 금홍석, 방해석, 모나자이트, 저어콘 및 인회석 등이 산출된다. 금홍석은 엽리상 석영맥내 유색대에서 자형내지 중립질 입단으로 어두운 금홍석과 밝은 금홍석으로 산출된다. 금홍석의 화학조성은 89.69~98.71 wt.% (TiO₂), 0.25~7.04 wt.% (WO₃), 0.30~2.56 wt.% (FeO), 0.00~1.71 wt.% (Nb₂O₅), 0.17~0.35 wt.% (HfO₂), 0.00~0.30 wt.% (V₂O₃), 0.00~0.35 wt.% (Cr₂O₃) 및 0.04~0.25 wt.% (Al₂O₃)으로 밝은 금홍석이 어두운 금홍석보다 WO₃, Nb₂O₅ 및 FeO 원소들의 함량이 높게 산출되며 서로 다른 시기에 형성된 것으로 생각된다. 어두운 금홍석과 밝은 금홍석내 미량원소들은 어두운 금홍석 [(V³⁺, Cr³⁺) + (Nb⁵⁺, Sb⁵⁺) ↔ 2Ti⁴⁺, 4Cr³⁺ (or 2W⁶⁺) ↔ 3Ti⁴⁺ (W⁶⁺ ↔ 2Cr³⁺), V⁴⁺ ↔ Ti⁴⁺], 밝은 금홍석 [2Fe³⁺ + W⁶⁺ ↔ 3Ti⁴⁺, 3Fe²⁺ + W⁶⁺ ↔ Ti⁴⁺ + (V³⁺, Al³⁺, Cr³⁺) +Nb⁵⁺]로써 치환관계가 있었다. 이들 자료를 근거로, 어두운 금홍석은 광역변성작용 동안 모암광물들의 변질 시 광물내 존재했던 V³⁺, V⁴⁺, Cr³⁺, Nb⁵⁺, Sb⁵⁺, W⁶⁺과 같은 양이온들의 재 농집에 의해 형성되었으나 밝은 금홍석은 ductile shear 시 높은 함량의 Fe²⁺ 및 W⁶⁺ 양이온들을 함유한 열수용액의 유입에 따른 어두운 금홍석과 반응에 의해 어두운 금홍석에 존재하였던 V³⁺, V⁴⁺, Al³⁺, Cr³⁺ 및 Nb⁵⁺과 같은 양이온들의 재 농집에 의해 형성된 것으로 생각된다.

• 한국해양공학회지
• /
• 제12권3호통권29호
• /
• pp.49-59
• /
• 1998

The damage mechanism of $Cr_2O_3$ plasma coated soda-lime glass and uncoated glass by steel ball particle impact was analyzed in this study. And the shape variation of the cracks was investigated by stereo-microscope according to the impact velocity and steel ball diameter. In order to improve the damage reduction effect by $Cr_2O_3$ coating layer, crack size was measured and surface erosion state was observed for both of two kinds of specimen after impact experiment. And the results were compared with each other. The 4-point bending test was performed according to ASTM D790 testing method to evaluate the effect of coating layer for bending strength variation. As a result, it was found that the crack size of $Cr_2O_3$ coated specimen was smaller than that of uncoated one, because of the impact absorption by interior pores in the coating layer and the load dispersion by the structural characteristic of the coating layer. For the specimens subjected to the steel ball impact, the bending strength of coated specimen was higher than that of uncoated specimen.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1999년도 춘계학술발표회요약집
• /
• pp.262-262
• /
• 1999

• 한국재료학회지
• /
• 제24권9호
• /
• pp.495-501
• /
• 2014

Despite having many attractive properties, $ZrO_2$ ceramic has a low fracture toughness which limits its wide application. One of the most obvious tactics to improve its mechanical properties has been to add a reinforcing agent to formulate a nanostructured composite material. Nanopowders of $ZrO_2$ and Cr were synthesized from $CrO_3$ and Zr powder by high energy ball milling for 10 h. Dense nanocrystalline $2/3Cr-ZrO_2$ composite was consolidated by a high-frequency induction heated sintering method within 5 min at $600^{\circ}C$ from mechanically synthesized powder. The method was found to enable not only rapid densification but also the inhibition of grain growth, preserving the nano-scale microstructure. Highly dense $2/3Cr-ZrO_2$ composite with relative density of up to 99.5% was produced under simultaneous application of a 1 GPa pressure and the induced current. The hardness and fracture toughness of the composite were 534 kg/mm2 and $7MPa{\cdot}m1/2$, respectively. The composite was determined to have good biocompatibility.

• 마이크로전자및패키징학회지
• /
• 제14권1호
• /
• pp.61-68
• /
• 2007

임베디드 PCB 기판내 유전체 재료인 Atomic Layer Deposition(ALD) $Al_2O_3$ 박막과 전극재료인 스퍼터 증착된 Cu박막 사이의 계면접착력을 $90^{\circ}$ 필 테스트방법으로 측정하여 순수 빔 굽힘을 가정한 에너지 평형 해석을 통하여 계면파괴에너지를 구하였다. $Cu/Al_2O_3$의 계면파괴에너지(${\Gamma}$)는 매우 약하여 측정할 수 없었으나, 접착력 향상층 Cr 박막을 삽입하여 $Cr/Al_2O_3$의 계면파괴에너지는 $10.8{\pm}5.5g/mm$를 얻었다. $Al_2O_3$ 표면에 $0.123W/cm^2$ 의 power density로 2분간 $Ar^+$ RF 플라즈마 전처리를 하고 Cr박막을 삽입한 $Cr/Al_2O_3$ 계면파괴에너지는 $39.8{\pm}3.2g/mm$으로 매우 크게 증가하였는데, 이는 $Ar^+$ RF 플라즈마 전처리에 따른 mechanical interlocking효과와 Cr-O 화학결합 효과가 동시에 기여한 것으로 생각된다.

• 대한기계학회논문집A
• /
• 제21권5호
• /
• pp.791-799
• /
• 1997

The wear characteristics and wear mechanisms of plasma sprayed Al/sub 2/ O/sub 3/-40%TiO/sub 2/ and Cr/sub 2/O/sub 3/ deposited on casting aluminum alloy(AC4C) were investigated. Specimens were processed for various coating thicknesses. Ball on disk type wear tester was used for wear test. The scratch test on plasma sprayed coating surface showed that critical load to break the coating layer was greater than 40 N. The critical load increase with the increase of coating thickness of specimens. The friction coefficient of Cr/sub 2/O/sub 3/ coating layer was less than that of Al/sub 2/O/sub 3/-40%TiO/sub 2/ coating layer. The wear resistance of Cr/sub 2/O/sub 3/ coating layer was greater than that of Al/sub 2/O/sub 3/-40%TiO/sub 2/ coating layer. Microscopic observation of worn surfaces was made by SEM. SEM observation showed that the main mechanism of wear for Al/sub 2/O/sub 3/-40%TiO/sub 2/ coating layer was abrasive wear under 50 N. For the case of Al/sub 2/O/sub 3/-40%TiO/sub 2/ coating layer, as the surface cracks perpendicular to sliding direction propagated, the wear debris was generated in wear track. However, the main mechanism of wear for Cr/sub 2/O/sub 3/ coating layer was brittle fracture under 150 N.

• 대한전기학회논문지
• /
• 제41권6호
• /
• pp.687-693
• /
• 1992

To improve dielectric, piezoelectric and temperature stability in 0.50Pb(SnS11/2TSbS11/2T)OS13T - 0.35PbTiOS13T - 0.60PbZrOS13T + 0.4[wt%]MnOS12T piezoelectric ceramics which is used for surface acoustic wave devices, CrS12TOS13T was added and the specimens were fabricated by Hot Press method, and their characteristics were measured with CrS12TOS13T addition. From the results, in the specimen added by 0.2[wt%]CrS12TOS13T, dielectric constant and mechanical quality factor were 380 and 2307, respectively, and it was suited for surface acoustic wave device and the temperature coefficient of the resonant frequency in the specimen added by 0.4[wt%]CrS12TOS13T was the least value of 74.96[ppm/$^{\circ}C$].