• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.1670-1672
• /
• 2000

The stability of ZnO-$Pr_{6}O_{11}$-CoO-$Cr_{2}O_{3}-Dy_{2}O_3$ based varistors with d.c. stress were investigated. ZnO varistor doped with 4.0 mol% $Dy_{2}O_3$ exhibited the highest nonlinear exponet, but stability was very poor because of low density. In particular, the varistor containing 0.5 mol% $Dy_{2}O_3$ showed very excellent V-I characteristic, which the nonlinear exponent was 67.39 and leakage current was 1.18 ${\mu}A$, and high stability.

• 한국세라믹학회지
• /
• 제22권6호
• /
• pp.37-41
• /
• 1985

Several $Al_2O_3$-based polycrystalline which had different dopant ratio in the range of 0.5mol% were prepared by doping pure $Cr_2O_3$, $ZrO_2$, $HfO_3$ Single crystalline which had same composition with above polycrystalline were made by means of floating zone method. This study examined the role of each dopant for enhancing the mefchanical properties of $Al_2O_3$-based Ceramics. Optical micrographs $({\times}200)$ of $Al_2O_3-Cr_2O_3$ single crystal showing not only radial crack (rc) on the specimen surface but median crack (mc) and lateral crack (lc) under surface at the edge of indentation mark. Fracture toughness of $Al_2O_3$-based Ceramics was increased with $ZrO_2$ content. Alloying effect of $Cr_2O_3$ contributed to the hardness of $Al_2O_3$ based ceramics.

• KSBB Journal
• /
• 제15권1호
• /
• pp.49-54
• /
• 2000

1.0%(w/v)의 CMC 담체는 고정화를 유지할 수 있는 점도를 가지며 0.1 M 이하의 양이온과 이온가교결합을 할 수 있는 농도이다. Luminometer tube내의 시료에 유동을 최소화함으로써 산소의 공급을 일정하게 하여 P. phosphoreum을 고정화 30분 후 bioluminescence intensity가 안정되어 바로 측정할 수 있는 장점을 가지고 있었다. 1.0%(w/v) CMC담체는 pH 6.92로 최적조건인 pH 7.0에 근접했으며, 발광기작에 필요한 산소전달(oxygen transfer)이 1.5%(w/v)~3.0%(w/v) CMC 담체보다 뛰어나 Bioluminescence intensity의 안정성을 부여하였다. Cr-화합물인 $Na_{2}CrO_{4}$, $K_{2}CrO_{4}$, $CrO_{3}$, CrK$(SO_4)_{2}$ 및 $CrCl_{3}$의 CMC담체에 대한 민감도는 $\gamma$값을 이용해서 $EC_{50}$값으로 나타내었을 때 $Na_{2}CrO_{4}$, $K_{2}CrO_{4}$, CrK$(SO_4)_{2}$ 및 $CrCl_{3}$ 의 $EC_{50}$값이 1.0%(w/v)CMC에서는 5.4~16.3 g/L으로 1.5%(w/v)~3.0%(w/v) CMC에서는 6.2~555.9 g/L의 범위로 나타났다. 이것은 1.0%(w/v) CMC가 낮은 독성 농도에서 bioluminescence intensity가 50% 감소함을 알 수 있고, 상관계수($R^2$)가 0.911~0.990 으로 높게 산출되었다. 따라서 1.0%(w/v) CMC 담체가 P. phosphoreum의 biolumincsene에 안정성을 주었으며, 독성물질에 가장 민감하다는 것을 알 수 있었다.

• 한국재료학회지
• /
• 제10권8호
• /
• pp.540-544
• /
• 2000

열처리가 분위기 Y(sub)0.7Ca(sub)0.3CrO(sub)3<원문참조>의 치밀화 및 전기적 특서에 미치는 영향을 조사하였다. 1700$^{\circ}C$ 공기중에서 12시간 소결된 시편을 1400$^{\circ}C$ O$_2$, Air, N$_2$에서 시간의 변화에 따라 재열처리하였다. N$_2$분위기에서 열처리한 Y(sub)0.7Ca(sub)0.3CrO(sub)3<원문참조>의 밀도는 열처리 시간이 증가함에 따라 다음과 같이 변화하였다. 4.5(0hr)\longrightarrow5.35(24hrs)\longrightarrow5.1g/$cm^3$(48hrs). 전기전도도는 열처리 시간이 증가함에 따라 큰변화는 없었으며, 활성화 에너지는 0.16eV로 일정하였다. Air에서 재열처리한 경우 밀도는 거의 변하지 않았으나, 활성화 에너지는 시간에 따라 0.19에서 0.115eV까지 변화하였다. O$_2$분위기에서 열철한 Y(sub)0.7Ca(sub)0.3CrO(sub)3<원문참조>의 밀도는 24시간 열처리후 4.9(g/$cm^3$)로 증가후 일정하였다. 24시간 이상 N 분위기에서 열처리한 경우와는 다르게 기지상과 비슷한 조성의 제 2상의 석출되었으며 24시간동안 열처리한 시편까지는 전기 전도도에 변화가 없었다. 그러나 48시간 동안 열처리된 시편의 전기 전도도는 감소하였고 활성화 에너지는 400K이하에서 0.167eV, 400K 이상에서 0.24eV이었다.

• 공업화학
• /
• 제7권1호
• /
• pp.34-42
• /
• 1996

합성에메랄드[$(BeO)_3(Al_{2-x}Cr_xO_3)(SiO_2)_6$]단결정을 flux법에 의하여 육성하였다. 출발물질로 BeO, $Al_2O_3$와 $SiO_2$ 시약을 화학양론비로 혼합하여 사용하였다. 에메랄드 단결정의 성장 조건은 다음과 같다. 온도범위 ; $1150{\sim}900^{\circ}C$, 냉각속도 ; 2, 4, $10^{\circ}C/hr$, 융제 : $Li_2CO_3$, $V_2O_5$, 첨가제 ; $Cr_2O_3$. 에메랄드 단결정의 크기는 2, 4, $10^{\circ}C/hr$의 냉각속도에 의존하였다. 얻어진 에메랄드 단결정을 동정하였고, 그 결과는 다음과 같다. 즉, 결정계 ; 육방정계, 격자상수 ; a=0.921nm, c=0.917nm, 결정의 크기 ; 최대 $0.80{\times}0.95mm^2(c{\times}m)$, 방위 ; c(1000), $m(10{\bar{1}}0)$.

• 한국표면공학회지
• /
• 제52권5호
• /
• pp.251-257
• /
• 2019

Fe-9Cr-2W steels were corroded at $600-800^{\circ}C$ for up to 100 hr in ($Na_2SO_4-K_2SO_4-Fe_2O_3$)-($CO_2-0.3%SO_2-6%O_2$) mixed gas. The poor condition samples formed thick oxide scales that consisted primarily of $Fe_2O_3$ as the major oxide and $Fe_3O_4$, FeO as the minor one through preferential oxidation of Fe. Fe-9Cr-2W steels corroded fast, forming thick and non-protective scale. The scale divided into the outer and inner layer, which consisted of the outer Fe-O layer and the inner (Fe,Cr)-O layer containing some (Fe,Cr)-S.

• 한국세라믹학회지
• /
• 제48권2호
• /
• pp.160-167
• /
• 2011

Plasma sprayed ceramic coatings inherently contain pores and usually also cracks. Post-treatment of the plasma sprayed coatings is a way to close the connected pores and cracks. In this study, post-sealing treatment in plasma sprayed $Al_2O_3$ coatings was employed to overcome the reduction of coating properties. $Al_2O_3$ plasma thermal spray coating was made on aluminum alloys plate, $CrO_3$ post coating and heat treatment at $550^{\circ}C$ was carried out in order for final $Cr_2O_3$ to be saturated through phase transformation. Chromia sealing began at the fine defect in coated microstructure, while larger pores were permeated later. The increase in concentration and treatment frequency of sealing solution resulted in the decrease of porosity of coating layer, while cracks occurred partially after the third treatment. After twice treatment of 10M $CrO_3$ solution, microhardness and breakdown voltage of $Al_2O_3$ coatings were found to increase by ${\fallingdotseq}$ 50% and ${\fallingdotseq}$ 390% respectively than without post-treatment.

• 한국재료학회지
• /
• 제23권2호
• /
• pp.128-134
• /
• 2013

A study on the corrosion behavior of Inconel alloys and Incoloy 800H in molten salt of LiCl-$Li_2O$ was investigated at $650^{\circ}C$ for 24-312 hours in an oxidation atmosphere. The order of the corrosion rate was Inconel 600 < Inconel 601 < Incoloy 800H < Inconel 690. Inconel 600 showed the best performance suggesting that the content of Fe, Cr and Ni are the important factor for corrosion resistance in hot molten salt oxidation conditions. The corrosion products of Inconel 600 and Inconel 601 were $Cr_2O_3$ and $NiFe_2O_4$, In case of Inconel 690, a single layer of $Cr_2O_3$ was formed in the early stage of corrosion and an outer layer of $NiFe_2O_4$ and inner layer of $Cr_2O_3$ were formed with an increase of corrosion time. In the case of Incoloy 800H, $Cr_2O_3$ and $FeCr_2O_4$ were observed. Most of the outer scale of the alloys was observed to be spalled from the results of the SEM analysis and the unspalled scale which adhered to the substrate was composed of three layers. The outer layer, the middle one, and the inner one were Fe, Cr, and Ni-rich, respectively. Inconel 600 showed localized corrosion behavior and Inconel 601, 690 and Incoloy 800H showed uniform corrosion behavior. Ni improves the corrosion resistance and too much Cr and/or Fe content deteriorates the corrosion resistance.

• 열처리공학회지
• /
• 제31권4호
• /
• pp.171-179
• /
• 2018

Copper powder dispersed with 4 vol.% of $Cr_2O_3$ was successfully produced by a simple milling at 210 K with a mixture of $Cu_2O$, Cu and Cr elemental powders, followed by Hot Pressing (HP) at 1123 K and 50 MPa for 2h to consolidate the milled powder. The microstructure of the HPed material was characterized by standard metallographic techniques such as XRD (X-ray Diffraction), TEM and STEM-EDS. The results of STEMEDS analysis showed that the HPed materials comprised a mixture of nanocrystalline Cu matrix and $Cr_2O_3$ dispersoid with a homogeneous bimodal size distribution. The mechanical properties of the HPed materials were characterized by micro Vickers hardness test at room temperature. The thermodynamic considerations on the heat of formation, the incubation time to ignite MSR (Mechanically induced Self-sustaining Reaction), and the adiabatic temperature for the heat of displacement reaction between the oxide-metal are made for the delayed formation of $Cr_2O_3$ dispersoid in terms of MSR suppression. The results of TEM observation and hardness test indicated that the relatively large dispersoids in the HPed materials are attributed to the significant coarsening for the high temperature consolidation; this leads to the low Vickers hardness value. Based on the thermodynamic calculation for the operating processes with a limited number of parameters, the formation kinetics and coarsening of the $Cr_2O_3$ dispersoid are discussed.

• 한국표면공학회지
• /
• 제52권5호
• /
• pp.246-250
• /
• 2019

Nano-multilayered $Cr_{25.2}Al_{19.5}Si_{4.7}N_{50.5}$ films were deposited on the steel substrate by cathodic arc plasma deposition. They were corroded at $900^{\circ}C$ in $Ar/1%SO_2$ gas in order to study their corrosion behavior in sulfidizing/oxidizing environments. Despite the presence of sulfur in the gaseous environment, the corrosion was governed by oxidation, leading to formation of protective oxides such as $Cr_2O_3$ and ${\alpha}-Al_2O_3$, where Si was dissolved. Iron diffused outward from the substrate to the film surface, and oxidized to $Fe_2O_3$ and $Fe_3O_4$. The films were corrosion-resistant up to 150 h owing to the formation of thin ($Cr_2O_3$ and/or ${\alpha}-Al_2O_3$)-rich oxide layers. However, they failed when corroded at $900^{\circ}C$ for 300 h, resulting in the formation of layered oxide scales due to not only outward diffusion of Cr, Al, Si, Fe and N, but also inward movement of sulfur and oxygen.