• EDISON SW 활용 경진대회 논문집
• /
• 제6회(2016년)
• /
• pp.15-18
• /
• 2016

본 연구는 조류발전 터빈의 블레이드 형상 최적화 해석 시스템 개발에 대한 사전연구의 일환으로 EDISON CFD의 프로펠러 단독성능 S/W와 SNUFOAM ShipMesh Advanced 자동격자생성기를 이용하여 조류발전 터빈 주위 유동장에 대한 수치해석을 수행하였다. TSR 조건 변화에 따라 수치해석을 수행하고 이에 대한 power, total coefficient를 동일한 조건에서 수행된 실험결과와 비교 검증하여 해석자의 신뢰도를 확인하였다. 또한, 블레이드 전체를 모델링한 full body 해석과 하나의 블레이드만을 모델링한 single body 해석 결과를 비교하여 경제적이면서 정도 높은 터빈 성능해석 프로세스를 제안하였다. 조류발전 터빈의 TSR 조건 변화에 따라 낮은 TSR 조건에서는 국부적 와동발생에 의해 $C_P$가 감소하는 것을 확인하였고 설계 TSR에서 가장 좋은 효율을 보임을 확인하였다. 이를 통해 suction side의 압력 분포, 팁 와동의 강도 등 성능개선을 위한 주요한 설계변수를 식별하였다.

• 한국세라믹학회지
• /
• 제47권5호
• /
• pp.457-460
• /
• 2010

$SmCoO_3$ system was investigated for their application to themoelectric materials. All specimens showed p-type semiconducting behavior and their electrical conductivity ($\sigma$), Seebeck coefficient (S) and power factor were measured at high temperature. And the effect of dopant ions on their thermoelectrical properties were also investigated. $Fe^{3+}$ ion doped into $Co^{3+}$ site enhanced the Seebeck coefficient and decreased the electrical conductivity simultaneously. The maximum Seebeck coefficient value for 60% doping case reached to 780 ${\mu}V$/K at $240^{\circ}C$. However $Fe^{3+}$ doped system cause an negative effect on power factor value. In case of the pure phase, the maximum Seebeck coefficient value reached to 290 ${\mu}V$/K at $240^{\circ}C$ and the maximum electrical conductivity was obtained 748 1/(ohm$\times$cm) at $960^{\circ}C$. As a result, the maximum power factor was obtained $1.49\times10^{-4}$ W/$mK^2$ at $550^{\circ}C$.

• 대한전자공학회논문지SD
• /
• 제46권10호
• /
• pp.1-8
• /
• 2009

본 논문에서는 아날로그 및 디지털 집적시스템에서 사용될 수 있는 온도변화에 무관한 파워-업 검출기 회로를 제안하였다. 제안된 파워-업 검출기는 트랜지스터의 문턱전압과 이동도의 상호 온도보상 기술을 이용하여 nMOS 분압기와 pMOS 분압기의 출력 전압이 온도에 무관한 특성을 갖도록 하여 온도 변화에 따른 파워-업 전압의 변화량을 최소화하였다. 68-nm CMOS 공정을 이용한 시뮬레이션 결과, 제안된 파워-업 검출기는 파워-업 전압 1.0V 기준으로 $-30^{\circ}C$에서 $90^{\circ}C$의 온도변화 조건에서 4 mV의 매우 작은 파워-업 감지 전압 변화량을 갖는 출력 특성을 보였고, 기존 회로에 비해 92.6%의 파워-업 감지 전압 변화량 감소를 확인하였다.

• Wind and Structures
• /
• 제27권3호
• /
• pp.187-197
• /
• 2018

In this study, aerodynamic characteristics of a horizontal axis wind turbine (HAWT) were evaluated and discussed in terms of measured data in existing onshore wind farm. Five wind turbines (T1, T2, T3, T4 and T5) were selected, and hub-height wind speed, $U_D$, wind turbine power output, P and turbine rotational speed, ${\Omega}$ data measured from these turbines were used for evaluation. In order to obtain characteristics of axial flow induction factor, a, power coefficient, $C_p$, thrust force coefficient, $C_T$, thrust force, T and tangential flow induction factor, a', Blade Element Momentum (BEM) theory was used. According to the results obtained, during a year, probability density of turbines at a rotational speed of 16.1 rpm was determined as approximately 45%. Optimum tip speed ratio was calculated to be 7.12 for most efficient wind turbine. Maximum $C_p$ was found to be 30% corresponding to this tip speed ratio.

• 디지털융복합연구
• /
• 제17권10호
• /
• pp.349-357
• /
• 2019

본 연구의 목적은 체질량지수가 인슐린, 혈당 및 당화혈색소에 미치는 영향을 확인하는 것이다. 연구방법은 국민건강영양조사 2015년 자료를 분석하여, 서술적 통계, t-test, ANOVA, Pearson correlation coefficient과 단계적 다중회귀분석을 적용하였다(SPSS WIN 25.0). 주요결과는, 체질량지수는 인슐린(r=0.397, p<0.001), 공복혈당(r=0.241, p<0.001) 및 당화혈색소(r=0.237, p<0.001)와 양의 상관관계를 나타내었다. 인슐린에 영향요인은 과체중(${\beta}=.130$, t=8.193, p<0.001),비만(${\beta}=.390$, t=24.390, p<0.001), 연령이며 설명력은13.1% (F=53.584, p<0.001)였다. 공복혈당에 영향요인은 과체중(${\beta}=.072$, t=4.478, p<0.001), 비만(${\beta}=.186$, t=11.485, p<0.001), 연령이며 설명력은 10.6%(F=42.351, p<0.001)였다. 당화혈색소에 영향요인은 과체중(${\beta}=.059$, t=3.712, p<0.001), 비만(${\beta}=.190$, t=11.895, p<0.001), 연령, 성별이며 설명력은 14.1% (F=58.134, p<0.001)였다. 본 연구결과를 바탕으로 당뇨병 예방 및 관리프로그램에 비만관련 중재가 포함되어야 한다.

• 전자공학회논문지A
• /
• 제33A권4호
• /
• pp.136-141
• /
• 1996

In this paper, a new CMOS on-chip current reference circit for memory, operational amplifiers, comparators, and data converters is proposed. The reference current is almost independent of temeprature and power-supply variations. In the proposed circuit, the current component with a positive temeprature coefficient cancels that with a negative temperature coefficient each other. While conventional curretn and voltage reference circuits require BiCMOS or bipolar process, the presented circuit can be integrated on a single chip with other digiral and analog circits using a standard CMOS process and an extra mask is not needed. The prototype is fabricated employing th esamsung 1.0um p-well double-poly double-metal CMOS process and the chip area is 300um${\times}$135 um. The proposed reference current circuit shows the temperature coefficient of 380 ppm/.deg. C with the temperature changes form 30$^{\circ}C$ to 80$^{\circ}C$, and the output variation of $\pm$ 1.4% with the supply voltage changes from 4.5 V to 5.5 V.

• 동력기계공학회지
• /
• 제11권4호
• /
• pp.50-55
• /
• 2007

Nowadays, demands on super low temperature condition for industrial and commercial uses are thriving. Considering of its wide application in the present and the future, study of the super-low temperature refrigeration system should be actively carried out. This study is aimed to investigate refrigeration capacity and coefficient of performance(COP) of the cascade refrigeration system, as well as to get the system which can reach evaporator temperature of $-70^{\circ}C$. For this purpose, R290 and R170 are charged in high stage and low stage respectively. Finally the characteristics of system using R290 and R170 will be proposed. Additionally, In this experiment, the flow rate of air flowing through the LS evaporator and the compressor inlet pressure were varied to investigate the refrigeration capacity and coefficient of performance characteristics.

• 한국분말재료학회지
• /
• 제8권2호
• /
• pp.110-116
• /
• 2001

Abstract To investigate the effect of mechanical alloying process to thermoelectric properties of PbTe sintered body, Pb-Te mixed powder with Pb : Te : 1 : 1 composition was mechanically alloyed using tumbler-ball mill. Thermoelectric properties of the sintered body were evaluated by measuring of the Seebeck coefficient and specific electric resistivity from the room temperature to 50$0^{\circ}C$. Sintered body of only mechanically alloyed PbTe powder showed p-type behavior at the room temperature, and occurred type transition from p-type to n-type at about 30$0^{\circ}C$. PbTe sintered body which was fabricated using heat treated powder in $H_2$ atmosphere after mechanical alloying showed stable n-type behavior under 50$0^{\circ}C$. N-type PbTe sintered body fabricated by mechanical alloying process had 4 times higher power factor than that fabricated by the melt-crushing process. Application of a mechanical alloying process to fabricate of n-type PbTe thermoelectric material seemed to be useful to increase the power factor of PbTe sintered body.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년 학술대회 논문집 정보 및 제어부문
• /
• pp.609-611
• /
• 2006

This paper describes a CMOS sub-bandgap reference using Pseudo-Resistors which can be widely used in flash memory, DRAM, ADC and Power management circuits. Bandgap reference circuit operates weak inversion for reducing power consumption and uses Pseudo-Resistors for reducing the chip area, instead of big resistor. It is implemented in 0.35um Standard 1P4M CMOS process. The temperature coefficient is 5ppm/$^{\circ}C$ from $40^{\circ}C$ to $100^{\circ}C$ and minimum power supply voltage is 1.2V The core area is 1177um${\times}$617um. Total current is below 2.8uA and output voltage is 0.598V at $27^{\circ}C$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.149-152
• /
• 2001

A great deal of attention has been focused on the application of miniaturized piezoelectric transformers to the low power source for the microsystem. The dielectric and piezoelectric properties of Pb(Mn,W,Sb,Nb)O$_3$-Pb(Zr,Ti)O$_3$ ceramics have been investigated on different calcination(750$^{\circ}C$∼950$^{\circ}C$) and sintering(1100$^{\circ}C$∼1300$^{\circ}C$) temperatures. The perovskitic phase was formed by the solid phase reaction of the oxides. Anisotropic (k$\sub$t/k$\sub$p/) properties of electromechanical coupling coefficient and piezoelectric coefficient have been proven to be depending on processing temperatures. The value of electromechanical coupling factor of K$\sub$p/>0.51 and a mechanical quality factor of Q$\sub$m/>2000 were obtained. The piezoelectric transformer was prepared using this ceramics with the composition of Pb(Mn,W,Sb,Nb)O$_3$-Pb(Zr,Ti)O$_3$ We studied the influence of different processing temperature on the microstructure and piezoelectric properties of complex PZT-based ceramics. and the characteristic of piezoelectric transformer.