• Journal of the korean academy of Pediatric Dentistry
• /
• v.34 no.1
• /
• pp.122-129
• /
• 2007

The purpose of this study was to evaluate the effects of a various light curing time on the residual monomers released from light-cured dental sealant, and to examine the effectiveness of surface treatment in reducing the oxygen-inhibited layer of light-cured dental sealant($Helioseal^{(R)}$ F, Vivadent, Liechtenstein). Specimens were cured with a halogen light curing unit(XL 3000, 3M, USA) for 20, 40, 60s. Surface treatment of a light-cured dental sealant included no treatment(control group), a 10-seconds exposure to distilled water(Group I), 10-seconds manual application using a cotton pellet wetted with 75% alcohol(Group II), and 10-seconds application of a water/pumice slurry using a rubber cup on a slow-speed handpiece The specimens were eluted in distilled water for 10 minutes. All elutes were analyzed by HPLC for identification and quantitive analysis of monomers. The results of this study can be summarized as follows. 1. None of the chromatograms of the tested sealant displayed peaks with the same retention time as that of the standard solution, except for TEGDMA. 2. The release of TEGDMA decreased with increasing curing time in conventional halogen light. 3. All surface treatment group had a decrease of monomer release in comparison with no treatment group. 4. Treatment that Group III eliminated the greatest amount of any type of residual monomers. 5. The elution of unreacted monomers from curing with halogen curing unit for 60s and Group III was less than other groups.

• Korean Journal of Ecology and Environment
• /
• v.38 no.1 s.110
• /
• pp.83-94
• /
• 2005

The objective of the study was to elucidate early life history of Rhinogobius brunneus, based on laboratory observations and field works, along with its courtship and spawning behaviors. The male and female fish matured were sampled for the lab experiments from Gap-Stream, which is one of the tributaries of Geum-River, Korea. The spawning behaviors and courtship of matured adults had a typical pattern; matured males of Rhinogobius brunneus built up spawning nests and had their own territory before the spawning, and the behavior then triggered the egg spawning of female with active courtship. The females attached elliptic egg mass as a single layer, on the stones below the spawning nest. After the spawning, the egg mass was guarded by males only until the hatching. The size of egg fertilized, measured by microscope was about 1.5${\pm}$0.1mm in length and 0.7${\pm}$0.1 mm in the egg's width. According to the lab experiments conducted under four temperature regime, the lapsed time for the hatching was shortened as temperatures increased in the treatments. On the contrary to the hatching time, the average length of newly hatched larvae showed a reverse relation with water temperature. The larvae, considered a final stage of the early life history was about 3.6 mm in total length for water temperature of $18^{\circ}C$, whereas they were between 3.1 mm and 3.2 mm for over $25^{\circ}C$. This indicates that higher water temperature may decrease the growth rate in the early life history. These results may provide valuable information for the population conservation and ecosystem protection under accelerated water pollution and habitat degradations in Korea.

• Journal of the Korean Vacuum Society
• /
• v.12 no.3
• /
• pp.168-173
• /
• 2003

Recently, according to the rapid progress in Flat-panel-display industry, there has been a growing interest in the poly-Si process. Compared with a-Si, poly-Si offers significantly high carrier mobility, so it has many advantages to high response rate in Thin Film Transistors (TFT's). We have investigated a new process for the high temperature Solid Phase Crystallization (SPC) of a-Si films without any damages on glass substrates using thin film heater. because the thin film heater annealing method is a very rapid thermal process, it has very low thermal budget compared to the conventional furnace annealing. therefore it has some characteristics such as selective area crystallization, high temperature annealing using glass substrates. A 500 $\AA$-thick a-Si film was crystallized by the heat transferred from the resistively heated thin film heaters through $SiO_2$ intermediate layer. a 1000 $\AA$-thick $TiSi_2$ thin film confined to have 15 $\textrm{mm}^{-1}$ length and various line width from 200 to 400 $\mu\textrm{m}$ was used as the thin film heater. By this method, we successfully crystallized 500 $\AA$-thick a-Si thin films at a high temperature estimated above $850^{\circ}C$ in a few seconds without any thermal deformation of g1ass substrates. These surprising results were due to the very small thermal budget of the thin film heaters and rapid thermal behavior such as fast heating and cooling. Moreover, we investigated the time dependency of the SPC of a-Si films by observing the crystallization phenomena at every 20 seconds during annealing process. We suggests the individual managements of nucleation and grain growth steps of poly-Si in SPC of a-Si with the precise control of annealing temperature. In conclusion, we show the SPC of a-Si by the thin film heaters and many advantages of the thin film heater annealing over other processes

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.11 no.1
• /
• pp.187-202
• /
• 1989

This study was undertaken to investigate the effect of indomethacin on prostaglandins in 4-Nitroquinoline-N-Oxide (4-NQO) induced palatal carcinoma of albino rats. 128 Sprague-Dawley strain albino rats-about 100g in body weight-were used in this study, divided into as belows; 1. Normal group (16-albino rats) with no treatment, 2. Control group (16-albino rats) treated with prophylene application onto palatal mucosa 3 times a week. 3. Experimental group I (48-albino rats) treated with 0.5% 4-NQO in prophylene application onto palatal mucosa 3 times a week. 4. Experimental group II (48-albino rats) treated with 0.5% 4-NQO in prophylene application with administered $20{\mu}g/ml$ of indomethacin in drinking water ad. lib. Four animals were sacrificed 7th, 13th, 19th, and 25th week respectively in normal and control group, and 7th, 9th, 11th, 13th, 15th, 17th, 19th, 21st, 23rd, 25th, 27th and 29th week respectively in experimental group I and II at each time. The palatal and lingual tissues were excised and kept frozen at $-70^{\circ}C$. Densitometer scan and Beta-counting counter were used for the thin layer chromatography of the arachidonic acid metabolites. The obtained results were as belows; 1. In normal and control group, there was little change of the arachidonic acid metabolites during experiment period, and the tissue homogenates included prostaglandin $D_2$, 6-keto-prostaglandin $F_{1{\alpha}}$, prostaglandin $E_2$, thromboxane $B_2$, prostaglandin $F_{2{\alpha}}$ in that order of relative abundances. 2. In experimental group I, prostaglandin $D_2$, and prostaglandin $E_2$ were increased, while 6-keto-prostaglandin $F_{1{\alpha}}$ and thromboxane $B_2$ were decreased in relative abundances of arachidonic acid metabolites. And there was little change in prostaglandin $F_{1{\alpha}}$ 3. In experimental group II, prostaglandin $D_2$, and prostaglandin $E_2$ were increased, while 6-keto-prostaglandin $F_{1{\alpha}}$ and thromboxane $B_2$ were decreased in relative abundances of arachidonic acid metabolites. And there was little change in prostaglandin $F_{2{\alpha}}$ also. 4. In the range of increase in prostaglandin $D_2$, and prostaglandin $E_2$, and that of decrease in 6-keto-prostaglandin $F_{1{\alpha}}$ and thromboxane $B_2$, in relative abundances, there was wider in experimental group I than in group II. 5. In the range of increase in prostaglandin $D_2$, and prostaglandin $E_2$, and that of decrease in 6-keto-prostaglandin $F_{1{\alpha}}$ and thromboxane $B_2$, in relative abundances, there was wider in palatal mucosa than in lingual mucosa in experimental group I and II.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.5-5
• /
• 2009

Thin-film-transistors (TFTs) that can be prepared at low temperatures have attracted much attention because of the great potential for transparent and flexible electronics. One of the mainstreams in this field is the use of organic semiconductors such as pentacene. But device performance of the organic TFTs is still limited due to low field-effect mobility and rapid degradation after exposing to air. Alternative approach is the use of amorphous oxide semiconductors as a channel. Amorphous oxide semiconductors (AOSs) based TFTs showed the fast technological development, because AOS films can be fabricated at room temperature and exhibit the possibility in application like flexible display, electronic paper, and larges solar cells. Among the various AOSs, a-IGZO has lots of advantages because it has high channel mobility, uniform surface roughness and good transparency. [1] The high mobility is attributed to the overlap of spherical s-orbital of the heavy post-transition metal cations. This study demonstrated the effect of the variation in channel thickness from 30nm to 200nm on the TFT device performance. When the thickness was increased, turn-on voltage and subthreshold swing was decreased. The a-IGZO channels and source/drain metals were deposited with shadow mask. The a-IGZO channel layer was deposited on $SiO_2$/p-Si substrates by RF magnetron sputtering, where RF power is 150W. And working pressure is 3m Torr, at $O_2/Ar$ (2/28 sccm) atmosphere. The electrodes were formed with electron-beam evaporated Ti (30 nm) and Au (70 nm) bilayer. Finally, Al (150nm) as a gate metal was thermal-evaporated. TFT devices were heat-treated in a furnace at 250 $^{\circ}C$ and nitrogen atmosphere for 1hour. The electrical properties of the TFTs were measured using a probe-station. The TFT with channel thickness of 150nm exhibits a good subthreshold swing (SS) of 0.72 V/decade and on-off ratio of $1{\times}10^8$. The field effect mobility and threshold voltage were evaluated as 7.2 and 8 V, respectively.

• Asian-Australasian Journal of Animal Sciences
• /
• v.17 no.4
• /
• pp.518-522
• /
• 2004

This experiment was conducted to investigate the effects of different levels of dried leftover food (DLF) in the diet on feed utilization and egg-laying performance of hens. One hundred sixty-eight, 18 week old Tetra brown commercial layers, were assigned to 7 treatments in a completely randomized design. Each treatment has four replications per treatment with six animals per replication. All the experimental animals were fed diets for 7 weeks. The treatments included 1) control group without DLF, 2) diet with 10% DLF, 3) diet with 20% DLF, 4) diet with 30% DLF, 5) 10% higher protein level of diet with 10% DLF, 6) 20% higher protein level of diet with 20% DLF and 7) 30% higher protein level of diet with 30% DLF. Average daily feed intake (ADFI) tended to be improved with DLF feeding. ADFI of group fed diets with 20% was significantly higher than that of control (p<0.05). Feed conversions of DLFfed groups were higher than that of control. Egg production tended to be higher in groups fed diets with 10% DLF than control diet without significant differences (p>0.05). However, those of groups fed diets containing 20 and 30% DLF were lower than that of control. Supplementing protein source to DLF-containing diets improved egg production (p<0.05). Increasing level of DLF in the diet for layer decreased egg weight and egg mass compared to control without significant differences (p>0.05). Protein supplementation to DLF-containing diets increased egg mass without significant difference (p>0.05). The range of egg cholesterol concentration of DLF-fed groups was 11.94-14.10 mg/g while that of control group was 12.31 mg/g although there was no significant difference among treatments (p>0.05).

• Journal of Biosystems Engineering
• /
• v.14 no.4
• /
• pp.272-281
• /
• 1989

It is desirable for the vertical wind tunnel which can build uniform air flow across the vertical duct to be used for the purpose of the investigation of the aerodynamic properties of grains. This study was conducted to examine how the air velocity profile in the vertical duct is influenced by the various alternations of the elements of the wind tunnel, and to prepare design guidance of the vertical wind tunnel which can be used for investigating aerodynamic properties of grains. In addition, several tests were conducted to locate the test section which can be applicable for determining the terminal velocity of grain. The following conclusions were obtained from the study: 1. The size and the location of the outlet of the plenum chamber should be determined such that the outlet air flow is less affected by the air flow and the back pressure by the side wall of the chamber. 2. The honeycomb was not helpful for attaining uniform air flow in case that the air flow profile at the bottom of the vertical duct is serverely different from the ideal one. 3. Even though considerable pressure drop was resulted from the screens installed within the vertical duct, the screens were helpful for attaining uniform air flow in the duct. 4. It is desirable for the test section to be located at the position that not only the air flow of the duct is not disturbed by the distorted back pressure in the plenum chamber, but also less boundary layer is developed.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.330-332
• /
• 2009

Highly stable bottom gate thin film transistors(TFTs) with a zinc indium tin oxide(Zn-In-Sn-O:ZITO) channel layer have been fabricated by rf-magnetron co-sputtering using a indium tin oxide(ITO:90/10), a tin oxide and a zinc oxide targets. The ZITO TFT (W/L=$40{\mu}m/20{\mu}m$) has a mobility of 24.6 $cm^2$/V.s, a subthreshold swing of 0.12V/dec., a turn-on voltage of -0.4V and an on/off ratio of >$10^9$. When gate field of $1.8{\times}10^5$ V/cm was applied with source-drain current of $3{\mu}A$ at $60^{\circ}C$, the threshold voltage shift was ~0.18 V after 135 hours. We fabricated AM-OLED driven by highly stable bottom gate Zn-In-Sn-O TFT array.

• Journal of Veterinary Clinics
• /
• v.22 no.4
• /
• pp.336-341
• /
• 2005

Anabolic steroid compounds are widely used for the increase of muscle mass, density of bone and athletic ability. The present study conducted to evaluate the effects of nandrolone decanoate (ND), one of the anabolic steroid compounds, on disuse muscle atrophy and healing process of bone in dogs. Twenty physically healthy dogs of both sexes were used in this experiment and divided into three groups: group A (control), group B (low dose M-1.5 mg/kg) and group C (high dose ND-7.5 mg/kg). One-mm strip of full thickness bone was excised from the radius below the pronator teres muscle for the artificial fracture and then the fractured ends were fixed in apposition with bone plate leaving 1mm gap, and finally immobilized externally by Robert John's bandage for 4 weeks. ND was administered intramuscularly once a week far 8 weeks. Body weight, muscle mass change and fracture gap of the bone were evaluated immediately after surgery, and 2, 4, and 8 weeks after surgery. The rates of muscle mass change 8 weeks after surgery were $-2.75\pm0.16\%,\;1.68\pm0.11\%\;and\;1.74\pm0.48\%$ in groups A, B and C, respectively. The significant increase (p<0.05) of muscle mass increments were found in the treated groups. The fibrous connective tissue layer in the fracture gaps of the treated groups increased more than the control, especially in the group C at 4th week. More dense fibrous connective tissue were found in the treated groups at 8th week. Collectively, our results suggested that ND was an effective anabolic agent for the immobilized disuse muscle and bone healing.

• 한국해양학회지
• /
• v.9 no.2
• /
• pp.52-58
• /
• 1974

The water temperature distribution and the water movement closely related with it, in the east side of Korea, was condidered. Special emphasis was paid on the low temperature phenomenon near Ulgi. It was known from the temperature distribution in the east side of Korea that the Tsushima current continues to flow northward at the surface near Sokcho. Also the influence of the cold water extends from the North to the South with increasing depth. The formation of the cold core near Ulgi was explained as due mainly to the existence of the boundary layer near the surface, and partly to the effect of the wind. This inclination of the boundary layer has the value of about 3.0m/Km, and the lower cold current velocity computed using this value lies in the range of those observed by Nishida(1926, 1927). The upwelling velocity was computed approximately as 1.4 10$\^$-3/ cm/sec, and the maximum distance to which the boundarylayer can rise or fall from it's equilibrium position was considered as below 10m.