• Nuclear Engineering and Technology
• /
• v.52 no.10
• /
• pp.2230-2237
• /
• 2020

Self-priming venturi scrubber is one of the most effective devices used to collect aerosols and soluble gas pollutants from gaseous stream during severe accident in a nuclear power plant. The present study focuses on investigation of dust particle removal efficiency of the venturi scrubber both experimentally and theoretically. Venturi scrubber captures the dust particles in tiny water droplets flowing into it. Inertial impaction is the main mechanism of particles collection in venturi scrubber. The water injected into venturi throat is in the form of jets through multiple holes present at venturi throat. In this study, aerosols removal efficiency of self-priming venturi scrubber was experimentally measured for different operating conditions. Alumina (Al₂O₃) particles with 0.4-㎛ diameter and 3950 kg/㎥ density were treated as aerosols. Removal efficiency was calculated for different gas flow rates i.e. 3-6 ㎥/h and liquid flow rates i.e. 0.009-0.025 ㎥/h. Experimental results depict that aerosols removal efficiency increases with the increase in throat velocity and liquid head. While at lower air flow rate of 3 ㎥/h, removal efficiency decreases with the increase in liquid head. A theoretical model of venturi scrubber was also employed and experimental results were compared with mathematical model. Experimental results are found to be in good agreement with theoretical results.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.10
• /
• pp.665-669
• /
• 2015

We investigated and compared two methods of in-situ oxidation and chemical etching treatment (CET) to remove the boron rich layer (BRL). The BRL is generally formed during boron doping process. It has to be controlled in order not to degrade carrier lifetime and reduce electrical properties. A boron emitter is formed using $BBr_3$ liquid source at $930^{\circ}C$. After that, in-situ oxidation was followed by injecting oxygen of 1,000 sccm into the furnace during ramp down step and compared with CET using a mixture of acid solution for a short time. Then, we analyzed passivation effect by depositing $Al_2O_3$. The results gave a carrier lifetime of $110.9{\mu}s$, an open-circuit voltage ($V_{oc}$) of 635 mV at in-situ oxidation and a carrier lifetime of $188.5{\mu}s$, an $V_{oc}$ of 650 mV at CET. As a result, CET shows better properties than in-situ oxidation because of removing BRL uniformly.

• Journal of Sensor Science and Technology
• /
• v.19 no.4
• /
• pp.291-296
• /
• 2010

Recently, recycling method of waste wafer has been an area of solar cell to cut costs. Micro_blasting is one of the promising candidates for recycling of waste wafer due to their extremely simple and cost-effective process. In this paper, we attempt to explore the effect of micro_blasting and DRE(damage removal etching) process for solar cell. The optimal process conditions of micro_blasting are as follows: $10{\mu}m$ sized $Al_2O_3$ powder, jetting pressure of 400 kPa, and scan_speed of 30 cm/s. And the particles formed on micro_blasted wafer were removed by DRE precess which was performed by using HNA(HF/$HNO_3$/$CH_3COOH$) and TMAH(tetramethyl ammonium hydroxide). Structural analysis was done using a-step and the XRD patterns.

• Mineral and Industry
• /
• v.18 no.1
• /
• pp.1-17
• /
• 2005

국내의 납석 광상은 대부분 백악기의 화산암류들이 열수변질되어 형성된 광상으로서, 주로 전남 및 경남 지역에 밀집되어 분포한다. 납석은 지질 여건상 주로 경상분지 내에 국제적인 규모의 풍부한 부존자원이 있지만, 그 동안의 개발에 의해서 고품위 황석들은 상당히 채진된 상황이다. 현재 개발되고 있는 광체들은 몇 곳의 광산을 제외하고는 대부분 저품위 광상을 이루고 있기 때문에, 새로운 광체의 탐광이 이루어지지 않는다면 앞으로 고품위 광석에 관한 한 국내의 수요를 충당하기 어려운 상황에 이를 것으로 예견된다. 현재 국내에서 납석으로 개발되고 있는 광석의 상당수(대략 $40\%$ 정도)가 엄밀한 의미에서는 사실상 납석이 아닌 고령토나 견운모 광석인 것으로 밝혀졌다. 엽납석을 함유하는 정상적인 형태의 납석들은 그수반 점토광물상에 의거하여 (l) 엽납석질, (2) 딕카이트질. (3) 일라이트질 및 (4) 딕카이트-일라이트질 유형으로 구분될 수 있다. 고령토 광물로는 대부분 딕카이트가 수반되고 외국에서는 흔히 수반되는 것으로 알려져 있는 고령석은 거의 함유되지 않는 것이 특징이다. 석영은 납석에서 점토광물 못지않게 그 용도를 가름하는 주요 성분으로서 대부분의 광석 유형에서 수반되지만 특히 일라이트질 납석에서 흔히 그리고 보다 많이 수반되는 양상을 보인다. X-선회절 정랑분석법은 납석의 품위를 산정하는데 유력한 수단이 될 수 있다. 특히 납석 이외의 점토광물들의 조성, 특히 일라이트의 함유 정도는 납석의 용도별 품위와 품질을 가름하는 주요 사항이다. 화학분석에 의한 납석의 평가 방식은 특히 납석의 백색 도기류와 같은 각종 세라믹스 제조 용도에서의 품질 평가에 결정적인 단서를 제공하는 유력한 평가수단이다. 특히 착색유발 성분인 철분의 존재와 그 함량을 정하고 요업용도에서 중요한 $Al_3O_3$와 알칼리 성분 함량을 검증하는데 필수적인 평가 방법이다. 이외에 주사전자현미경 관찰을 통해서 납석의 주요 품질 기준이 되는 극미립상 엽납석의 결정형, 조직 및 미시적 산출상태를 보다 정밀하게 평가할 수 있는 방안을 제공한다. 현행 광업법상의 납석을 비롯한 관련 광종들의 광물분류 체계가 모호하게 설정되어 있고 관련 인허가 부서에서의 전문성 및 지도력 부족으로 관련 산업계에 심각한 비효율성과 오류가 야기되고 있는 실정이다. 이를 개선하기 위해서는 납석의 광석평가 방식이 그 품위와 품질 개념 하에서 응용광물학적으로 적용되어야 할 것이다.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.2
• /
• pp.70-77
• /
• 2012

The Ladle Furnace Slag, about 20% of the electric arc furnace slag, has high content of free CaO and free MgO, which generates the expansion collapse by hydration reaction. Although many researchers have been endeavoring to recycle the EAF reducing slag in construction fields, there is not found the effective recycling method up to now. However, the LFS(Ladle Furnace Slag) contains mineral composition of the system of calcium aluminate with high-reactivity. Therefore, it is possible to developed the quick setting property and the high strength at the early age by the rapid cooling. This study aimed to check the reactive minerals and predict the reactivity with water on the LFS discharged from different steel product plants. The test results show that many types of LFS has hydration reactivity and can use in construction field as a inorganic binder with the rapid setting property.

• Resources Recycling
• /
• v.30 no.6
• /
• pp.68-75
• /
• 2021

This study aims to investigate the manufacturing process of calcium chloride-based special cement, i.e., CCA (calcium chloro aluminate, C₁₁A₇·CaCl₂), which uses limestone, by using one type of random industrial by-product, domestic coal ash, cement kiln dust. The manufacturing process of was examined in detail, and the results suggested that the amount of CCA synthesized increased with an increase in the firing temperature. The manufacturing process of CCA was investigated at 1200℃, which was determined as the optimum firing temperature. The results showed that in general, the amount of CCA synthesized tended to increase with an increase in the firing time; however, the clinker melted when the firing time was more than 30 min, thereby suggesting that a firing time of less than 20 min would be suitable for the clinkering process. The optimal firing conditions for manufacturing CCA were obtained as follows: heating rate of 10 ℃/min, firing temperature of 1200 ℃, and holding time of 20 min. The results also suggest that manufacturing CCA will be easier when high chlorine-containing cement kiln dust is used.

• Journal of the Mineralogical Society of Korea
• /
• v.6 no.2
• /
• pp.116-121
• /
• 1993

A single crystla of zeolite $Na_{78}Rb_{28}-X$ (approximate composition) was prepared by exposing $Na_{92}-X$ at $350^{\circ}C$ to 0.1 Torr of rubidium vapor, and its structure was determined by single-crystal x-ray diffraction methods in the cubic space group, Fd3, ${\alpha}=25.045(4){\AA}$. The structure was refined to the final error indices $R_1=0.082$ and $R_2=0.084$ with 353 for which I>$3{\sigma}(I)$. Only about 28 of the 92 $Na^+$ ions per unit cell were reduced and only about 14 of the 28 $Na^0$ atoms produced were retained within the zeolite. A $Na_5{^{4+}}$ cluster is present within each sodalite cavity. It is a centered tetrahedron (like $CH_4$) with bond $length=2.80(2){\AA}$ and angle tetrahedral by symmetry, and shows the full symmetry of its site. $T_d$, at the center of the sodalite cavity. Each of the four terminal atoms of the $Na_5{^{4+}}$ cluster bond to three framework oxygens at $2.36(2){\AA}$. At the centers of some double 6-rings are sodium atoms which bridge linearly between $Na_5{^{4+}}$ clusters to form agglomerations such as short zig-zag chains $Na_5{^{4+}}$ clusters. Delocalized electrons, located primarily on the sodiums at centers of the sodalite and (likely) double-six-ring cavities, contribute to the stability of the clusters.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.8
• /
• pp.597-601
• /
• 2013

The accelerated thermal aging of a CSPE were carried out for 0, 80.82, 161.63 days at $100^{\circ}C$, which are equal to 0, 40 and 80 years of aging at $50^{\circ}C$, respectively. The volume electrical resistivities of the seawater and freshwater flooding were measured through 3-terminal circuit diagram. The volume electrical resistivities of the 0y, 40y and 80y were $2.454{\times}10^{13}{\sim}1.377{\times}10^{14}{\Omega}{\cdot}cm$, $1.121{\times}10^{13}{\sim}7.529{\times}10^{13}{\Omega}{\cdot}cm$ and $1.284{\times}10^{13}{\sim}8.974{\times}10^{13}{\Omega}{\cdot}cm$ at room temperature, respectively. The dielectric constant of the 0y, 40y and 80y were 2.922~3.431, 2.613~3.285 and 2.921~3.332 at room temperature, respectively. It is certain that the ionic ($Na^+$, $Cl^-$, $Mg^{2+}$, ${SO_4}^{2-}$, $Ca^{2+}$, $K^+$) conduction current was formed by the salinity of the seawater. The volume electrical resistivity of the cleaned CSPE via freshwater trends slightly upward with the number of dried days at room temperature. As a result, the $CH_2$ component of thermally accelerated aged CSPE decreased after seawater and freshwater flooding for 5 days respectively, whereas the atoms such as Cl, O, Pb, Al, Si, Sb, S related with the conducting ion ($Na^+$, $Cl^-$, $Mg^{2+}$, ${SO_4}^{2-}$, $Ca^{2+}$, $K^+$) component increased relatively.

• Journal of the Korean Ceramic Society
• /
• v.39 no.11
• /
• pp.1042-1047
• /
• 2002

The sedimentation characteristics of ceramic fiber were analyzed when viscosity of the slurry for ceramic paper formation was varied and zeta potential change and degree of dispersion with pH were studied as well. The proper viscosity of the slurry for dispersion of fibers was between 28 and 31 cps. Zeta potential of the slurry was sensitively changed with pH adjustment and showed maximum value of -35~-36 mV at ph 7.5~9.5, which indicated better dispersion of ceramic fiber as zeta potential of the slurry was increased. The sedimentation rate of ceramic fiber in a slurry was reported minimum at the maximum zeta potential. Water content of the casted paper should be lower than 83% after vacuum dehydration for retention of binder and lower than 62% after press rolling for wet paper handling. The obtained ceramic paper had tensile strength and basis weight, $102 kgf/cm^2$ and $98 g/m^2$, respectively.

• Composites Research
• /
• v.23 no.2
• /
• pp.10-16
• /
• 2010

$Al_2O_3$ fiber and SiC particle hybrid metal matrix composites (MMCs) were manufactured by squeeze casting method investigated for their tribological properties. The pin specimens had different ratios of fiber to particle content but their total weight fraction was constant at 20 wt. %. Tribological tests were performed with a pin-on-disk friction and wear tester. The investigation of the dry tribological characteristics of hybrid MMCs were carried out at room temperature and elevated temperature of$100^{\circ}C$ and$150^{\circ}C$. The morphologies of worn surfaces were examined by scanning electron microscope (SEM) to observe tribological characteristics and investigate wear behavior. The results revealed that the wear resistance improved with the content of SiCp increased of the planar random (PR) MMCs at room temperature. At the elevated temperature, it revealed that the wear resistance of normal (N) MMCs was superior to that of the PR-MMCs due to PR-fibers were easily pulled out holistically from the worn surface. Meanwhile, the coefficient of friction decreased with the temperature increasing.