• Journal of Power Electronics
• /
• 제18권5호
• /
• pp.1513-1522
• /
• 2018

This paper proposes a new islanding detection method for inverter-based distributed generators by continuously injecting a negligible amount of 2nd order harmonic current. The proposed method adopts a proportional resonant (PR) controller for the output current control of the inverter, and a PR filter to extract the 2nd order harmonic voltage at the point of common coupling (PCC). The islanding state can be detected by measuring the magnitude ratio of the 2nd order harmonic voltage to the fundamental voltage at the PCC by injecting a 2nd order harmonic current with a 0.8% magnitude. The proposed method provides accurate and fast detection under grid voltage unbalance and load unbalance. The operation of the proposed method has been verified through simulations and experiments with a 5kW hardware set-up, considering the islanding test circuit suggested in UL1741.

• Journal of Electrical Engineering and Technology
• /
• 제8권3호
• /
• pp.507-515
• /
• 2013

This paper proposes a compensation method for the $2^{nd}$-order harmonic of single-phase grid-connected wind power generation systems. Theoretically, a single-phase grid-connected inverter system has no choice but to cause the $2^{nd}$-order harmonic to DC-link voltage. The reference active current is affected by the DC-link voltage. The output current from the reference active current is distorted by the $1^{st}$ and $3^{rd}$-order harmonic. The proposed method can compensate, conveniently, the reference active current with the $2^{nd}$-order harmonic. To reduce the $2^{nd}$-order ripple in the reference active current, proposed method takes a PR controller as a feed-forward compensator. PR controllers can implement selective harmonic compensation without excessive computational requirements; the use of these controllers simplifies the method. Both the simulation and experimental results agree well with the theoretical analysis.

• 전기학회논문지
• /
• 제67권1호
• /
• pp.29-37
• /
• 2018

Inrush current and fault current in a transformer need to be distinguished from one another. In order to do this, KEPCO uses a 2nd harmonic restraint/block method. We use two setting values for 2nd harmonic restraint; 15% and 10%. We also apply per-phase blocking method among various harmonic restraint methods. If the transformer is located at the radial system, we adjust 10% in the 2nd harmonic restraint, but this method is not enough to prevent mal-operations of the current differential relay and let us spend more time to change setting value again as the power system changes. In this paper, a more reasonable setting value for a 2nd harmonic blocking scheme in KEPCO is proposed. To present a proposed method, the fault data of the current differential relays which have occurred since 2009 are analyzed. To evaluate the performance of the proposed method, the results of the RTDS test for the current differential relay of the transformer by KEPCO are analyzed.

• 비파괴검사학회지
• /
• 제32권4호
• /
• pp.376-387
• /
• 2012

비선형 스프링 모델과 섭동법을 기초로 비선형 균열면에 경사 입사된 초음파에 의해 발생되는 2차 고조파 초음파의 크기를 계산하였다. 비선형 균열계면에서 만들어지는 반사파와 굴절파의 기본주파수 성분과 2차 고조파 성분의 크기를 입사각과 균열계면의 계면강성을 변화키면서 조사하였다. 계면강성에 관계없이 균열계면이 초음파 진행 방향과 비슷한 경우 반사와 굴절파 모두에서 2차 고조파의 발생은 거의 없었지만, 그렇지 않은 경우에는 계면 입사각은 물론 계면 강성에 따라 2차 고조파의 크기는 크게 변화하였다. 투과파는 물론 반사파에서도 2차 고조파 성분이 유의성 있게 발생됨을 수치 해석을 통해 확인하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 춘계학술대회 논문집 디스플레이 광소자 분야
• /
• pp.129-132
• /
• 2000

The PDP(Plasma Display Panel) barrier rib material on the glass substrate was patterned for fabrication of the PDP cell using Nd:YAG laser(1064 nm) which can generate the second(532 nm) and forth(266 nm) harmonic wave by HGM(harmonic generation modules). At a scan speed of 20 ${\mu}m/s$ with the second harmonic wave(532 nm) of Nd:YAG laser, the etching threshold laser fluence of the PDP material was 6.5 $mJ/cm^2$ and a sample(thickness = 180 ${\mu}m$) on the glass substrate was removed clearly at a laser fluence of 19.5 $mJ/cm^2$. In order to increase the throughput of the fabrication we divided a single-beam into multi-beams by using a metal mask between the sample and the focusing lens. As a result, 10 lines of PDP cell were formed by one laser beam scanning at a scan speed of 200 ${\mu}m/s$ and a laser fluence of 2.86 $J/cm^2$.

• Journal of Power Electronics
• /
• 제18권1호
• /
• pp.171-184
• /
• 2018

Unbalanced and distorted grid voltages cause the grid side current of a current source PWM rectifier to be heavily distorted. They can also cause the DC-link current to fluctuate with a huge amplitude. In order to enhance the performance of a current-source PWM rectifier under unbalanced and harmonic grid voltage conditions, a mathematical model of a current-source PWM rectifier is established and a flexible multi-objective control strategy is proposed to control the DC-link current and grid-current. The fundamental positive/negative sequence, $5^{th}$ and $7^{th}$ order harmonic components of the grid voltage are first separated with the proposed control strategy. The grid current reference are optimized based on three objectives: 1) sinusoidal and symmetrical grid current, 2) sinusoidal grid current and elimination of the DC-current $2^{nd}$ order fluctuations, and 3) elimination of the DC-current $2^{nd}$ and $6^{th}$ order fluctuations. To avoid separation of the grid current components, a multi-frequency proportional-resonant controller is applied to control the fundamental positive/negative sequence, $5^{th}$ and $7^{th}$ order harmonic current. Finally, experimental results verify the effectiveness of proposed control strategy.

• 한국전자파학회논문지
• /
• 제13권10호
• /
• pp.1054-1060
• /
• 2002

본 논문에서는 제 2차 고조파의 감쇠특성이 향상된 새로운 평행 결합선로 마이크로스트립 대역통과 여파기의 설계, 제작 및 특성에 관해서 소개한다. 결합선로에 연속적인 패턴을 사용함으로써 원하는 기본 통과대역의 특성을 향상시킴과 동시에 원하지 않는 고조파 통과대역은 제거한다. 또한 결합선로 사이의 간격, 마이크로스트립 선폭 및 길이와 같이 여파기 디자인을 위해 요구되는 매개변수의 복잡한 재계산이 필요하지 않다. 즉, 평행결합선로 마이크로스트립 여파기의 전통적인 디자인 방법으로 설계한 기본 구조에 규칙적인 변형을 주면서 손쉽게 구현할 수 있다. 이 새로운 여파기의 성능을 평가하기 위해 2.5 GHz에서 10 % 대역폭을 가지는 3차 Butterworth 대역통과 여파기와 10 GHz에서 15 % 대역폭을 가지는 5차 Chebyshev 대역통과 여파기가 사용됐다. 각각 5개와 3개의 정사각형 홈이 사용됐을 때 30 dB 이상의 고조파 감쇠가 발생하며 통과대역에서는 더 우수한 차단 특성이 있다.

• 전력전자학회논문지
• /
• 제14권1호
• /
• pp.54-61
• /
• 2009

본 논문에서는 강압형 DC-DC 컨버터의 성능 개선을 위한 스위칭 기법인 2차 SDSDM (Space Dithered Sigma Delta Modulation)방식을 제안한다. PWM (Pulse Width Modulation) 방식은 일정 스위칭 주파수 대역에서의 고조파로 인해 소음, 전자파 장애, 스위칭 손실 등을 유발한다. 이러한 문제를 해결하기 위한 DSDM 방식의 일종인 1차 SDSDM은 랜덤 디더(Random Dither) 발생기가 1차 SDM의 양자화기(quatizer) 입력단에 위치하여 스위칭 주파수가 분산된다. 강압형 DC/DC 컨버터에 제안하는 2차 SDSDM의 방식을 적용한 실험 결과를 통해 타당성을 검증한다.

• Journal of electromagnetic engineering and science
• /
• 제11권4호
• /
• pp.257-261
• /
• 2011

A highly efficient 2.4 GHz rectenna is designed using a harmonic rejection bandpass filter. The rectenna is printed on Rogers Duroid 5880 substrate with ${\varepsilon}_r$=2.2 and a thickness of 1.6 mm. The rectenna consists of a microstrip antenna and high order harmonic rejection bandpass filter, microstrip lowpass filter, and Schottky barrier diode (HSMS2820). The use of a $2^{nd}$ and $3^{rd}$ harmonic rejection microstrip bandpass filter in the rectenna results in high conversion efficiency. The proposed rectenna achieves a RF to DC conversion efficiency of 72.17 % when the received RF power is 63.09 mW.

• 한국광학회지
• /
• 제16권5호
• /
• pp.456-461
• /
• 2005

제2조화파 발생용으로 사용되는 볼록평면거울로 구성된 비대칭 불안정 공진기형 Nd:YAG 레이저의 빔질 특성을 수치적으로 분석하였다. 분석은 $M^2$, 공진기 내에서의 빔허리 직경, 모드 부피의 계산을 통해서 이루어 졌다. 수치적 계산 결과는 레이저 헤드가 볼록레이저 거울 근방에 위치한 비대칭 공진기 구조가 될 때 고효율의 제2조화파를 발생할 수 있는 조건이잘 충족됨을 보였다.