• Composites Research
• /
• v.26 no.2
• /
• pp.123-128
• /
• 2013

The PVDF (polyvinylidene fluoride) fibers were prepared using the wet spinning processing. To improve ${\beta}$-phase crystalline which closely related piezoelectric property PVDF wet spun fibers conducted post treatment. Post treatment is consisted of heat stretching and annealing process. The heat stretching and annealing conditions were controlled by changing temperature between glass transition temperature and melting temperature. From these experimental data, the resulting crystal structure of the ${\beta}$-phase crystalline was confirmed by FT-IR and XRD experiments. From these analysis results, optimum stretching and annealing conditions of the wet spun PVDF fibers were founded to increase high ${\beta}$-phase crystalline. Furthermore results showed that thermal processing had a direct effect on modifying the crystalline microstructure and also confirmed that heat stretching and annealing could increase the degree of crystallinity and ${\beta}$-phase crystalline. Finally, piezoelectric constant ($d_{11}$) of the post heat treated PVDF fibers reinforced composite were measured to investigate the feasibility for the sensing materials.

• Polymer(Korea)
• /
• v.35 no.2
• /
• pp.130-135
• /
• 2011

Along with the fast development of electronics, the demands of portable electronics and wireless sensors are growing rapidly. The need for self-powering materials capable of powering the electrical devices attached to them is increasing, The piezoelectric effect of polyvinylidene fluoride (PVDF) can be used for this purpose. PVDF has a special crystal structure consisting of a ${\beta}$-phase that can produce piezoelectricity. In this paper, multilayer PVDF films were fabricated to increase the ${\beta}$-phase content. A solution of 10% concentration N;N-dimethylacetamide (DMAc) in PVDF (PVDF/DMAc) was used to fabricate the films via spin coating technique with the following optimum process parameters: a spin rate of 850 rpm, spin time of 60 s, drying temperature of $60^{\circ}C$, and drying time of 30 min, Compared with single-layer PVDF films, the multilayer films exhibited higher ${\beta}$-phase content. The ${\beta}$-phase content of the films increased gradually with increasing number of layers until 4, Maximum ratio of ${\beta}$-phase content was 7.72.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.11
• /
• pp.712-715
• /
• 2016

In this paper, we fabricated flexible CNT/PVDF piezoelectric composite device by introducing CNTs (carbon nanotubes) into PVDF (poly-vinylidene fluoride) solution using spray coating technique. Flexible PEDOT:PSS conducting polymer was used as electrodes. We tried to improve the piezoelectric performance from the CNT/PVDF composite film by increasing the portion of the ${\beta}$-phase PVDF in the film. We confirmed the structural conformation of the CNT/PVDF composite film as a function of CNT concentration by using FT-IR (fourier transform infra-red). As increasing CNT concentration, portion of the ${\beta}$-phase PVDF and resulting piezoelectric performance increased in the CNT/PVDF composite film. We found that CNTs introduced were played as seeds for formation of the ${\beta}$-phase PVDF in the CNT/PVDF composite film and resulting improvement of the piezoelectric performance.

• Composites Research
• /
• v.29 no.4
• /
• pp.145-150
• /
• 2016

Polyvinylidene fluoride (PVDF) as a representative polymer with the piezoelectric property has been studied since the 1960s. Crystalline structure of poly(vinylidene fluoride) polymer is composed of five different crystal structure of the polymer as a semi-crystalline. Among the various crystal structures, ${\beta}-type$ crystal exhibits a piezoelectricity because the permanent dipoles are aligned in one direction. Generally ${\beta}-form$ crystal structure can be obtained through the transformation of the ${\alpha}-form$ crystal structure by the stretching and it can increase the amount through the after treatment as poling process after stretching. ${\beta}-form$ crystal structure the PVDF fibers produced by wet spinning is formed through a diffusion mechanism of a polar solvent in the coagulation bath. However, it has a disadvantage that the diffusion path of the solvent remains as pores in the fiber because the fiber solidification occurs simultaneously with the diffusion of the polar solvent. These pores play a role in reducing effect of poling process owing to effect of disturbances acting on the polarization by the electric field. In this work, the drying method using the microwave was introduced to remove more effectively the residual solvent and the pore within PVDF fibers produced through wet-spinning process and piezoelectric PVDF fibers was produced by transformation of the remaining ${\alpha}$ form crystal structure into ${\beta}-crystal$ structure through the stretching process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.7
• /
• pp.550-554
• /
• 2013

Carbon nanotubes (CNT) / polyvinylidene fluoride (PVDF) piezoelectric composite films for nanogenerator devices were fabricated by spray coating method. When the CNT/PVDF mixture solution passes through the spray nozzle with small diameter by the compressed nitrogen gas, electric charges are generated in the liquid by a triboelectric effect. Then randomly distributed ${\beta}$ phase PVDF film could be re-oriented by the electric field resulting from the accumulated electrical charges, and might be resulted in extremely one-directionally aligned ${\beta}$ phase PVDF film without additional electric field for poling. X-ray diffraction patterns were used to investigate crystal structure of the CNT/PVDF composite films. It was confirmed that they revealed extremely large portion of the ${\beta}$ phase PVDF crystalline in the film. Therefore we could obtain the poled CNT/PVDF piezoelectric composite films by the spray coating method without additional poling process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.3
• /
• pp.221-228
• /
• 1998

In this study, the $\beta$-Polyvinylidene fluoride(PVDF) thin films were fabricated by physical vapor deposition method. Also, the properties of dielectric relaxation were studied to understand carrier's behavior of PVDF thin films, to be regarded as the excellent piezo and pyroelectricity. In the process of vapor deposition, the $\beta$-PVDF thin films have been fabricated under the condition of the substrate temperature at 3$0^{\circ}C$, the applied electric field at 142.8kV/cm and the pressure at 2.0${\times}10^{-5}$torr. The dielectric properties of PVDF have been studied in the frequency range 10Hz to 1MHz at temperature from 30 to $100^{\circ}C$. The relative dielectric constant of $\alpha$ and $\beta$-PVDF were 6.8 and 9.8, respectively, under a frequency of 1kHz. Such a phenomenon was caused by the decrease in intermolecular forces originated by the phase-transition from the TGTG' molecular conformation to the TT planar zig-zag conformation. And the relative dielectric constant is increased as a measuring temperature increases, because of the reduction of relaxation time caused by the decrease of intermolecular force.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.256-256
• /
• 2013

Carbon nanotubes (CNT) / polyvinylidene fluoride (PVDF) piezoelectric composite films for nanogenerator devices were fabricated by spray coating method. When the CNT/PVDF mixture solution passes through the spray nozzle with small diameter by the compressed nitrogen gas, electric charges are generated in the liquid by a triboelectric effect. Then randomly distributed ${\beta}$ phase PVDF film could be re-oriented by the electric field resulting from the accumulated electrical charges, and might be resulted in extremely one-directionally aligned ${\beta}$ phase PVDF film without additional electric field for poling. X-ray diffraction patterns were used to investigate crystal structure of the CNT/PVDF composite films. It was confirmed that they revealed extremely large portion of the ${\beta}$ phase PVDF crystalline in the film. Therefore we could obtain the poled CNT/PVDF piezoelectric composite films by the spray coating method without additional poling process. Charge accumulation and resulting electric field generation mechanism by spray coating method were shown in Fig. 1. The capacitance of the CNT/PVDF films increased by adding CNTs into the PVDF matrix, and finally saturated. However, the I-V curves didn't show any saturation effect in the CNT concentration range of 0~4 wt%. Therefore we can control the performance of the devices fabricated from the CNT/PVDF composite film by adjusting the current level resulted from the CNT concentration with the uniform capacitance value.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.8
• /
• pp.565-571
• /
• 2003

We prepare the PVDF thin film using vacuum deposition method with the application of voltage and obtain the optimum deposition condition for $\beta$-PVDF thin film on the basis of the results of FT-IR, crystallinity of $\beta$ phase, surface roughness studies with varying the condition. The phase of PVDF thin film is analyzed by the FT-IR spectrum. When the substrate temperature and applied voltage increase from 3$0^{\circ}C$ to 9$0^{\circ}C$ and from 0kV to 9kV, respectively, the crystallinity of $\beta$ phase is introduced as large as 64%. It means that the substrate temperature and applied voltage allow the phase transition of $\beta$ phase to occur more easily. Also, the surface roughness of PVDF thin film decreases from 65.1nm to 36.6nm with the increase of substrate temperature. In results, we obtain the optimum deposition conditions for $\beta$-PVDF thin film from these experimental results and measure the Properties of the $\beta$-PVDF film deposited in the optimum condition. The dielectric properties such as dielectric constant and loss tangent decrease from 2.34 to 0.44 and from 0.27 to 0.04 with the increase of frequency, respectively.

• Journal of the Korean Vacuum Society
• /
• v.17 no.5
• /
• pp.448-454
• /
• 2008

The purpose of this paper is to discuss the fabrication of $\beta$-PVDF($\beta$-Polyvinylidene fluoride, ${\beta}-PVF_2$) organic thin films through the vapor deposition method and to investigate the piezoelectric properties of the organic thin films produced. Vapor deposition was performed under the following conditions : the temperature of evaporator, the applied electric field and the pressure of reaction chamber were $270^{\circ}C$, 142.4 kV/cm and $2.0{\times}10^{-5}Torr$, respectively. The results showed that the amount of $\beta$-form PVDF increased from 72 % to 95.5 % with an increase in the substrate temperature. In the case of a sensor response characteristic by varying the force moment from $1.372{\times}10^{-5}N{\cdot}m$ to $39.2{\times}10^{-5}N{\cdot}m$, the output voltage increased from 1.39V to 7.04V.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1549-1551
• /
• 1997

In this study, the $\beta$-Polyvinylidene fluoride($\beta$-PVDF) organic thin films were fabricated by physical vapor deposition method as one of the dry-processing methods and applying electric field during the vapor deposition. When the substrate temperature is $80^{\circ}C$, the PVDF organic thin films exhibit the characteristic absorption band of the $\beta$ forms $510cm^{-1}$, $602cm^{-1}$ and $1273cm^{-1}$, and the fraction of $\beta$ form crystals in the total crystalline content was 95%. The molecular structure of PVDF organic thin films were transformed from $\alpha$ to $\beta$ form with increasing of applied electric field and the control of substrate temperature.