• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.804-809
• /
• 2011

Tubular $Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-${\delta}$}$ membranes were prepared by extrusion. TGA results of green body membrane after extrusion showed three successive weight losses due to decomposition of organic additives and carbonate. Drying shrinkage rate of tubular $Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-${\delta}$}$ membranes was no change after 68 h and higher in the membrane with large outer diameter. XRD and SEM results showed the sintered membranes were the single phase structure and dense. The stoichiometric molar ratio agreed well with composition ratio calculated by EDS results for $Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-${\delta}$}$ membrane. Radial crushing strength of tubular $Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-${\delta}$}$ membrane with 0.95 mm thickness was 5.7 kgf/$mm^2$ and the oxygen permeation rate of same membrane was 146.85 mL/min ($Jo_2$=2.33 mL/$min{\cdot}cm^2$) at $950^{\circ}C$. Therefore, it was known that use of vacuum pump was more effective than that of sweep gas to obtain higher oxygen permeation flux.

• Archives of Pharmacal Research
• /
• v.26 no.7
• /
• pp.564-568
• /
• 2003

Pharmacokinetic and pharmacodynamic properties of gliclazide were studied after an oral administration of gliclazide tablets in healthy volunteers. After an overnight fasting, gliclazide tablet was orally administered to 11 volunteers; Additional 10 volunteers were used as a control group (i.e., no gliclazide administration). Blood samples were collected, and the concentration determined for gliclazide and glucose up to 24 after the administration. Standard pharmacokinetic analysis was carried out for gliclazide. Pharmacodynamic activity of the drug was expressed by increase of glucose concentration ($\Delta$PG), by area under the increase of glucose concentration-time curve ($AUC_{$\Delta$PG}$) or by the difference in increase of glucose concentration ($D_{$\Delta$PG}$) at each time between groups with and without gliclazide administration. Pharmacokinetic analysis revealed that $C_{max}, T_{max}$, CL/F (apparent clearance), V/F (apparent volume of distribution) and half-life of gliclazide were $4.69\pm1.38 mg/L, 3.45\pm1.11 h, 1.26\pm0.35 L/h, 17.78\pm5.27 L, and 9.99\pm2.15 h$, respectively. When compared with the no drug administration group, gliclazide decreased significantly the $AUC_{$\Delta$PG}$ s at 1, 1.5, 2, 2.5, 3 and 4 h (p＜0.05). The $\Delta$PGs were positively correlated with $AUC_{gliclazide}$ at 1 and 1.5 h (p＜0.05), and the correlation coefficient was maximum at 1 h (r = 0.642) and gradually decreased at 4 h after the administration. The $AUC_{$\Delta$PG}$s were positively correlated with $AUC_{gliclazide}$ at 1, 2, 3 and 4 h (p＜0.05), and the maximum correlation coefficient was obtained at 2 h (r=0.642) after the administration. The $D_{$\Delta$PG}$ reached the maximum at 1 h, remained constant from 1 h to 3 h, and decreased afterwards. Therefore, these observations indicated that maximum hypoglycemic effect of gliclazide was reached at approximately at 1.5 h after the administration and the effect decreased, probably because of the homeostasis mechanism, in health volunteers.

• Applied Chemistry for Engineering
• /
• v.7 no.3
• /
• pp.401-409
• /
• 1996

The effect of temperature on the cmc of sodium N-lauroyl-N-methyl taurate was examined. The cmc values were found to be decreased initially but increased further with the increase of temperature. From the temperature dependence of cmc, various thermodynamic properties were calculated. The effects of various electrolytes on the cmc of sodium N-lauroyl-N-methyl-taurate were also examined. The free energy of hydrophobic bond formation and the degree of dissociation of the micelles were calculated from log cmc vs. log counter ion concentration plots. The ${\Delta}H_m$ values were decreased with increasing the temperature and changed their signs from plus to minus at $40^{\circ}C{\sim}50^{\circ}C$. The ${\Delta}G_m$ values were decreased with the increase of electrolyte concentration and temperature.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.33 no.10
• /
• pp.1606-1610
• /
• 2004

This study was. conducted to investigate the effects of $\delta$-aminolevulinic acid supplementation on growth. performance, nutrient digestibility and hematological changes in weaned pigs. Seventy five Duroc${\times}$Yorkshire${\times}$ Landrace pigs (7.21$\pm$0.02 kg average BW) were used in a 20 d growth assay. Dietary treatments included 1) NC (negative control; basal diet), 2) PC (positive control; NC diet + 0.1% Apramycin + 0.1% Oxytetracycline), 3) ALA0.l (NC diet+0.l% $\delta$-aminolevulinic acid), 4) ALA0.2 (NC diet+0.2% $\delta$-aminolevulinic acid) and 5) ALA + AB (PC diet+0.2% $\delta$-aminolevulinic acid). In entire experimental period, ADG (Average Daily Gain) was greater in pigs fed ALA + AB diet than in pigs fed NC diet (p<0.05). However, there was no significant difference in ADG for pigs fed PC, ALA0.l or ALA0.2 diets. Also, ADFI (Average Daily Feed Intake) and G/F (Gain/Feed) were not affected by treatments. For 20 d, fecal digestibilities of DM (Dry Matter) and N (Nitrogen) were higher (p<0.05) for pigs fed ALA + AB diet than for pigs fed NC and ALA0.l diets. Total protein concentration of serum was increased in ALA + AB treatment compared to NC and PC treatments (p<0.05). In iron concentration of serum, pigs fed $\delta$-aminolevulinic acid supplementation diets were greater than for pigs fed NC and PC diets (p<0.05). TIBC (Total Iron Binding Capacity) concentration of serum was increased in ALA + AB treatment compared to NC, PC and ALA0.l treatments (p<0.05). Pigs fed ALA + AB and ALA0.2 diets were higher hemoglobin (Hb) and hematocrit (HCT) concentration of blood than pigs fed NC and PC diets (p<0.05). RBC and WEC concentrations of blood were significantly higher (p<0.05) for the pigs fed ALA0.2 and ALA + AB diets than for pigs fed NC diet. Lymphocyte concentration of blood was increased in $\delta$-aminolevulinic acid supplementation treatment compared to NC treatment (p<0.05). In conclusion, $\delta$-aminolevulinic acid supplementation for weanling pigs had improved growth performance and nutrient digestibilities and had increased total protein, iron, hemoglobin and lymphocyte concentration of blood. Also, feeding for dietary $\delta$-aminolevulinic acid and antibiotic mixture supplementation may have more higher effective growth performance in weanling pigs.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.22 no.4
• /
• pp.24-32
• /
• 1985

This paper presents the design method for multivalued logic functions using $I^2L$ circuits. First, the a비orithm that transforms delta functions into discrete functions of a truncated difference is obtained. The realization of multivalued logic circuits by this algorithm is discussed. And then, the design method is achieved by mixing discrete functions and delta functions using the modified algorithm for given multivalued truth tables. The techniques discussed here are easily extended to multi-input and multi-output logic circuits.

• Korean Journal of Optics and Photonics
• /
• v.5 no.1
• /
• pp.74-79
• /
• 1994

The characteristics of the type I and type II SHG in LiB305 crystals grown by TSSG method have been investigated using 1064 nm beam from a Q-switched Nd:YAG laser. The measured phase matching angles and angular acceptance bandwidths were $\theta_m=90^{\circ}, \phi_m=11.6^{\circ}$, <$\delta\theta_{int}L_{1/2}=3.3^{\circ}-cm^{1/2}, \theta\phi_{int}L=0.27^{\circ}-cm^{1/2}$ for type I SHG and $\theta_m=20^{\circ}, \phi_m=90^{\circ}$, TEX>$\delta\theta_{int}L_=0.65^{\circ}-cm, \theta\phi_{int}L^{1/2}=3.5^{\circ}-cm^{1/2}$ for type II SHG, respectively. Thp. type I NCPM temperature of 1064 nm beam was found to be $149^{\circ}C$ with the temperature bandwidth $\DeltaTL$of $4.8^{\circ}C-cm$. An energy conversion efficiency of about 1.8% with 2.6 mm thick LBO crystal at an incident power of TEX>$171 MW/\textrm{cm}^2$ was demonstrated. The measured $d_{32} was 0.74\pm0.05 pm/V$..

• The Journal of the Petrological Society of Korea
• /
• v.28 no.1
• /
• pp.1-13
• /
• 2019

The characteristics of the rock cleavage of Jurassic Geochang granite were analysed using the parameters from the length and spacing-cumulative frequency diagrams. The evaluation for three planes and three rock cleavages was performed using the 25 parameters such as (1~2) slope angle(${\alpha}^{\circ}$and ${\beta}^{\circ}$), (3) intersection angle(${\alpha}-{\beta}^{\circ}$), (4) exponent difference(${\lambda}_S-{\lambda}_L$), (5~12) length of line(oa, ob, ol, os, ss', ll' and sl') and (13~15) length ratio(ol/os, ss'/ll' and ll'/sl'), (16) mean length((ss'+ll')/2), (17~23) area (${\Delta}oaa^{\prime}$, ${\Delta}obb^{\prime}$, ${\Delta}obb^{\prime}$, ${\Delta}oaa_a^{\prime}$, ${\Delta}obb_a^{\prime}$, ${\Delta}ll^{\prime}s^{\prime}$, ${\Delta}ss^{\prime}l^{\prime}$ and ⏢$ll^{\prime}ss^{\prime}$) and (24~25) area difference(${\Delta}obb^{\prime}-{\Delta}oaa^{\prime}$ and ${\Delta}obb_a^{\prime}-{\Delta}oaa_a^{\prime}$). Firstly, the values of the 11 parameters(group I: No. 1, 3~4, 7, 9~10, 13, 15~16, 20 and 25), the 3 parameters(group II: No. 5, 8 and 17) and the 2 parameters(group III: No. 12 and 22) are in orders of H(hardway) < G(grain) < R(rift), R < G < H and G < H < R, respectively. On the contrary, the values of parameters belonging to the above three groups show reverse orders for three planes. Secondly, the generalized chart for three planes and three rock cleavages were made. From the related chart, the distribution types formed by the two diagrams related to lengths and spacings were derived. The diagrams related to spacings show upward curvature in the chart of rift plane(G1 & H1, R') and hardway(H1 & H2, H). On the contrary, the diagrams related to lengths show downward curvature. These two diagrams take the form of a convex lens in the upper section. Besides, the two diagrams cross each other in the lower section. The overall shape formed by the above two diagrams between three planes($H^{\prime}{\rightarrow}G^{\prime}{\rightarrow}R^{\prime}$) and three rock cleavages($R{\rightarrow}G{\rightarrow}H$) display in reverse order. Lastly, these types of correlation analysis is useful for discriminating three quarrying planes.

• The Journal of the Petrological Society of Korea
• /
• v.27 no.1
• /
• pp.1-15
• /
• 2018

The characteristics of the rock cleavage of Jurassic Geochang granite were analysed using the distribution of microcrack lengths and spacings. The length and spacing-cumulative diagrams for the six directions of rock cleavages were arranged in increasing order ($H2{\rightarrow}R1$) on the density (${\rho}$) of microcrack length. The various parameters were extracted through the combination of above two types of diagrams. The evaluation for the six directions of rock cleavages was performed using the four groups (I~IV) of parameters such as (I) intersection angle (${\alpha}-{\beta}$), exponent difference (${\lambda}_S-{\lambda}_L$), length of line (ol and ll'), length ratio (ol/os and ll'/sl'), mean length ((ss'+ll')/2), area of right-angled triangle (${\Delta}oaa_a^{\prime}$ and ${\Delta}obb_a^{\prime}$) and area difference (${\Delta}obb^{\prime}-{\Delta}oaa^{\prime}$ and ${\Delta}obb_a^{\prime}-{\Delta}oaa_a^{\prime}$), (II) length of line (oa and os) and area (${\Delta}oaa^{\prime}$), (III) length of line (sl') and length ratio (ss'/ll') and (IV) length of line (ob, ss' and ls') and area (${\Delta}obb^{\prime}$, ${\Delta}ll^{\prime}s^{\prime}$, ${\Delta}ss^{\prime}l^{\prime}$ and ⏢ll'ss'). The results of correlation analysis between the values of parameters for three rock cleavages and those for three planes are as follows. The values of parameters for three rock cleavages are in orders of (I) H(hardway, (H1 + H2)/2) < G(grain, (G1 + G2)/2) < R(rift, (R1 + R2)/2), (II) R < G < H, (III) G < H < R and (IV) H < G < R. On the contrary, the values of parameters for three planes are in orders of (I) R' < G' < H', (II) H' < G' < R' and (III and IV) R' < H' < G'. Especially the values of parameters belonging to group I and group II show mutual reverse orders. In conclusion, this type of correlation analysis is useful for discriminating three quarrying planes.

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10a
• /
• pp.16-20
• /
• 1988

This paper presents a new algorithm for solving the inverse kinematics in real-time applications. The end-tip movement of each link can be resolved into the basic resolution unit, .DELTA.l, which depends on link length, reduction ratio and resolution of the incremental encoder attached to the joint. When x- and y-axis projection of the end-tip movement are expressed in .DELTA.l unit, projectional increments .DELTA.x and .DELTA.y become -1, 0 or I by truncation. By using the incremental computation with these ternary value and some simple logic rules, a coordinate transformation can be realized. Through this approach, it should be noted that the floating-point arithmetic and the manipulation of trigonometric functions are completely eliminated. This paper demonstrates the proposed method in a parallelogram linkage type, two-link arm.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.1
• /
• pp.41-48
• /
• 2002

This paper presents a 18-mW, 2.5-㎓ fractional-N frequency synthesizer with l-bit $4^{th}$-order interpolative delta-sigma ($\Delta{\;}$\sum$)modulator to suppress fractional spurious tones while reducing in-band phase noise. A fractional-N frequency synthesizer with a quadruple prescaler has been designed and implemented in a $0.5-\mu\textrm{m}$ 15-GHz $f_t$ BiCMOS. Synthesizing 2.1 GHzwith less than 200 Hz resolution, it exhibits an in-band phase noise of less than -85 dBc/Hz at 1 KHz offset frequency with a reference spur of -85 dBc and no fractional spurs. The synthesizer also shows phase noise of -139 dBc/Hz at an offset frequency of 1.2 MHz from a 2.1GHz center frequency.