DOI QR코드

DOI QR Code

황동층의 형성과 선택적 아연 에칭을 통한 구리 필라 상 다공성 구리층의 제조와 구리-구리 플립칩 접합

Fabrication of Porous Cu Layers on Cu Pillars through Formation of Brass Layers and Selective Zn Etching, and Cu-to-Cu Flip-chip Bonding

  • 이완근 (서울과학기술대학교 신소재공학과) ;
  • 최광성 (전자통신연구원 저탄소집적기술 창의연구실) ;
  • 엄용성 (전자통신연구원 저탄소집적기술 창의연구실) ;
  • 이종현 (서울과학기술대학교 신소재공학과)
  • Wan-Geun Lee (Department of Materials Science & Engineering, Seoul National University of Science and Technology) ;
  • Kwang-Seong Choi (Low-Carbon Integration Tech, Creative Research Section, ETRI) ;
  • Yong-Sung Eom (Low-Carbon Integration Tech, Creative Research Section, ETRI) ;
  • Jong-Hyun Lee (Department of Materials Science & Engineering, Seoul National University of Science and Technology)
  • 투고 : 2023.12.22
  • 심사 : 2023.12.30
  • 발행 : 2023.12.30

초록

대기 중 구리-구리 플립칩(flip-chip) 접합을 위해 제안된 효율적 공정의 실현 가능성을 평가하고자 구리(Cu) 필라(pillar) 상 다공성 구리층의 형성 및 액상 환원제 투입 후 열압착 접합을 실시하였다. 구리 필라 상 다공성 구리층은 아연(Zn) 도금-합금화 열처리-선택적 아연 에칭(etching)의 3단계 공정으로 제조되었는데, 형성된 다공성 구리층의 두께는 평균 약 2.3 ㎛였다. 본 플립칩 접합은 형성 다공성 구리층에 환원성 용제를 침투시킨 후, 반건조 과정을 거쳐 열압착 소결접합으로 진행하였다. 용제로 인한 구리 산화막의 환원 거동과 함께 추가 산화가 최대한 억제되면서 열압착 동안 다공성 구리층은 약 1.1 ㎛의 두께로 치밀해지며 결국 구리-구리 플립칩 접합이 완수되었다. 그 결과 10 MPa의 가압력 하에서 대기 중 300 ℃에서 5분간 접합 시 약 11.2 MPa의 접합부 전단강도를 확보할 수 있었는데, 이는 약 50% 이하의 필라들만이 접합된 결과로서, 공정 최적화를 통해 모든 필라들의 접합을 유도할 경우 20 MPa 이상의 강도값을 쉽게 얻을 수 있을 것으로 분석되었다.

The feasibility of an efficient process proposed for Cu-Cu flip-chip bonding was evaluated by forming a porous Cu layer on Cu pillar and conducting thermo-compression sinter-bonding after the infiltration of a reducing agent. The porous Cu layers on Cu pillars were manufactured through a three-step process of Zn plating-heat treatment-Zn selective etching. The average thickness of the formed porous Cu layer was approximately 2.3 ㎛. The flip-chip bonding was accomplished after infiltrating reducing solvent into porous Cu layer and pre-heating, and the layers were finally conducted into sintered joints through thermo-compression. With reduction behavior of Cu oxides and suppression of additional oxidation by the solvent, the porous Cu layer densified to thickness of approximately 1.1 ㎛ during the thermo-compression, and the Cu-Cu flip-chip bonding was eventually completed. As a result, a shear strength of approximately 11.2 MPa could be achieved after the bonding for 5 min under a pressure of 10 MPa at 300 ℃ in air. Because that was a result of partial bonding by only about 50% of the pillars, it was anticipated that a shear strength of 20 MPa or more could easily be obtained if all the pillars were induced to bond through process optimization.

키워드

과제정보

본논문은과학기술정보통신부의재원으로한국연구재단의 지원(No. 2020M3H4A308176)을 받아 수행된 연구임.

참고문헌

  1. J. H. Lau, "Recent Advances and New Trends in Flip Chip Technology", J. Electron. Packag., 138(3), 030802 (2016).
  2. A. Roshanghias, A. Rodrigues, S. Schwarz, and A. Steiger-Thirsfeld, "Thermosonic direct Cu pillar bonding for 3D die stacking", SN Appl. Sci., 2(6), 1-9 (2020). https://doi.org/10.1007/s42452-020-2887-9
  3. M. S. Kim, M. S. Kang, J. H. Bang, C. W. Lee, M. S. Kim, and S. Yoo, "Interfacial reactions of fine-pitch Cu/Sn-3.5Ag pillar joints on Cu/Zn and Cu/Ni under bump metallurgies", Journal of Alloys and Compounds, 616, 394-400 (2014). https://doi.org/10.1016/j.jallcom.2014.07.124
  4. J. B. Kwak and S. Chung, "Thermal fatigue reliability for Cu-Pillar bump interconnection in flip chip on module and underfill effects", Soldering and Surface Mount Technology, 27(1), 1-6 (2015). https://doi.org/10.1108/SSMT-03-2014-0008
  5. Y. Ma, A. Roshanghias, and A. Binder, "A comparative study on direct Cu-Cu bonding methodologies for copper pillar bumped flip-chips", J. Mater. Sci.: Mater. Electron., 29(11), 9347-9353 (2018). https://doi.org/10.1007/s10854-018-8965-8
  6. S. L. P.-Siang, V. S. Rao, H. W. Yin, W. L. Ching, V. Kripesh, C. Lee, J. Lau, J. Milla, and A. Fenner, "Process development and reliability of microbumps", IEEE Transactions on Components and Packaging Technologies, 33(4), 747-753 (2010). https://doi.org/10.1109/TCAPT.2010.2046487
  7. E. C. Noh, H. W. Lee, and J. W. Yoon, "Recent Advances in Fine Pitch Cu Pillar Bumps for Advanced Semiconductor Packaging", J. Microelectron. Packag. Soc., 30(3), 1-10 (2023).
  8. J. S. Lee, H. S. Lee, M. S. Kim, S. S. Kim, and K. M, "A Study on Flux Immunity MUF for Improving Flip Chip PKG Reliability", J. Microelectron. Packag. Soc., 29(2), 49-52 (2022).
  9. J. W. Nah, J. H. Kim, H. M. Lee, and K. W. Paik, "Electromigration in flip chip solder bump of 97Pb-3Sn/37Pb-63Sn combination structure", Acta Materialia, 52(1), 129-136 (2004). https://doi.org/10.1016/j.actamat.2003.08.035
  10. D.-Q. Yu, T. C. Chai, M. L. Thew, Y. Y. Ong, V. S. Rao, L. C. Wai, and J. H. Lau, "Electromigration study of 50 ㎛ pitch micro solder bumps using four-point Kelvin structure", 2009 59th ECTC. IEEE, 930-935 (2009).
  11. M. Gerber, C. Beddingfield, S. O'connor, M. Yoo, M. Lee, D. Kang, S. Park, C. Zwenger, R. Darveaux, R. Lanzone, K. Park, "Next generation fine pitch Cu Pillar technology-Enabling next generation silicon nodes", 2011 61st ECTC. IEEE, 612-618 (2011).
  12. Z. Huang, R. E. Jones, and A. Jain, "Experimental investigation of electromigration failure in Cu-Sn-Cu micropads in 3D integrated circuits", Microelectron. Eng., 122, 46-51 (2014). https://doi.org/10.1016/j.mee.2014.03.003
  13. J. Li, Y. Zhang, Z. Haoliang, Z. Chen, C. Zhou, X. Liu, and W. Zhu, "The thermal cycling reliability of copper pillar solder bump in flip chip via thermal compression bonding", Microelectron. Reliab., 104, 113543 (2020).
  14. Y. Orii, K. Toriyama, S. Kohara, H. Noma, K. Okamoto, D. Toyoshima, and K. Uenishi, "Micro Structure Obser Vation and Reliability Behavior of Peripheral Flip Chip Interconnections with Solder-Capped Cu Pillar Bumps", Trans. JIEP., 4(1), 73-86 (2011). https://doi.org/10.5104/jiepeng.4.73
  15. H. Xu, I. Qin, H. Clauberg, B. Chylak, and V. L. Acoff, "Behavior of palladium and its impact on intermetallic growth in palladium-coated Cu wire bonding", Acta Materialia, 61(1), 79-88 (2013). https://doi.org/10.1016/j.actamat.2012.09.030
  16. B. Wu, S. Zhang, F. Wang, and Z. Chen, "Micro Copper Pillar Interconnection Using Thermosonic Flip Chip Bonding", J. Electron. Packag., 140(4), 044502 (2018).
  17. Z. Li, M. Li, Y. Xiao, and C. Wang, "Ultrarapid formation of homogeneous Cu6Sn5 and Cu3Sn intermetallic compound joints at room temperature using ultrasonic waves", Ultrasonics Sonochemistry, 21(3), 924-929 (2014). https://doi.org/10.1016/j.ultsonch.2013.09.020
  18. Y. Orii, K. Toriyama, H. Noma, Y. Oyama, H. Nishiwaki, M. Ishida, T. Nishio, N. C. LaBianca, C. Feger, "Ultrafine-pitch C2 flip chip interconnections with solder-capped Cu pillar bumps", 2009 59th ECTC. IEEE, 948-953 (2009).
  19. D. Save, F. Braud, J. Torres, F. Binder, C. Muller, J. O. Weidner, and W. Hasse, "Electromigration Resistance of Copper Interconnects", Microelectron. Eng., 33(1-4), 75-84 (1997). https://doi.org/10.1016/S0167-9317(96)00033-0
  20. Y. J. Jang, and J. P. Jung, "Scallop-free TSV, Copper Pillar and Hybrid Bonding for 3D Packaging", J. Microelectron. Packag. Soc., 29(4), 1-8 (2022).
  21. J. H. Kim, G. Y. Cheon, D. J. Kim, Y. B. Park, and Y. H. Ko, "A Study on Properties of Pb-free Solder Joints Combined Sn-Bi-Ag with Sn-Ag-Cu by Conditions of Reflow Soldering Processes", J. Microelectron. Packag. Soc., 29(3), 55-61 (2022).
  22. X. Ji, L. Du, S. He, H. van Zeijl, and G. Zhang, "Microstructural and micromechanical characterization of sintered nanocopper bump for flip-chip heterogeneous integration", Microelectronics Reliability, 150, 115180 (2023).
  23. J. Zurcher, L. Del Carro, G. Schlottig, D. N. Wright, A. S. B. Vardoy, M. M. V. Taklo, T. Mills, U. Zschenderlein, B. Wunderle, and T. Brunschwiler, "Sintering of copper nanoparticle pastes for microelectronic packaging", Diss. ETH Zurichpp, 343-349 (2016).
  24. Y. Mou, L. Jiaxin, H. Cheng, Y. Peng, and M. Chen, "Facile Preparation of Self-Reducible Cu Nanoparticle Paste for Low Temperature Cu-Cu Bonding", JOM, 71(9), 3076-3083 (2019). https://doi.org/10.1007/s11837-019-03517-5
  25. J.-J. Jhan, K. Wataya, H. Nishikawa, and C.-M. Chen, "Electrodeposition of nanocrystalline Cu for Cu-Cu direct bonding", J. Taiwan. Inst. Chem. Eng., 132, 104127 (2022).
  26. X. Liu, and H. Nishikawa, "Low-pressure Cu-Cu bonding using in-situ surface-modified microscale Cu particles for power device packaging", Scr. Mater., 120, 80-84 (2016). https://doi.org/10.1016/j.scriptamat.2016.04.018
  27. E. B. Choi, and J. H. Lee, "Tens-of-seconds solid-state sinter-bonding technique in air using in situ reduction of surface oxide layers on easily bendable dendritic Cu particles", Appl. Surf. Sci., 580, 152347 (2022).
  28. E. B. Choi, Y. J. Lee, and J. H. Lee, "Rapid sintering by thermo-compression in air using a paste containing bimodal-sized silver-coated copper particles and effects of particle size and surface finish type", J. Alloys. Compd., 897, 163223 (2022).
  29. Y. J. Lee, and J. H. Lee, "Ultrafast Sinter Bonding Between Cu Finishes Under Moderate Compression Using In Situ Derived Ag Formed via Low-Temperature Decomposition of Ag2O in the Bonding Paste", Met. Mater. Int., 29(6), 1775-1785 (2023). https://doi.org/10.1007/s12540-022-01320-7