Journal of Ocean Engineering and Technology (한국해양공학회지)

Korean Society of Ocean Engineers (한국해양공학회)
권호 표지

Control of Welding Distortion for Thin Panel Block Structure Using Plastic Counter-Deforming Method

소성 역변형법을 이용한 박판 평 블록의 용접변형 제어

  • 김상일 (로이드선급협회 아시아 옥포사무소)
  • Published : 2009.04.30
Download PDF
⟨ Previous Next ⟩

Abstract

The welding distortion of a hull structure in the shipbuilding industry is inevitable at each assembly stage. The geometric inaccuracy caused by welding distortion tends to preclude the introduction of automation and mechanization and requires additional man-hours for adjustment work during the following assembly stage. To overcome this problem, a distortion control method should be applied. For this purpose, it is necessary to develop an accurate prediction method that can explicitly account for the influence of various factors on the welding distortion. The validity of this prediction method must also be clarified through experiments. For the purpose of reducing the weld-induced bending deflection, this paper proposes the plastic counter-deforming method (PCDM), which uses line heating as the optimum distortion control method. The validity of this method was substantiated by a number of numerical simulations and actual measurements.

Keywords

References

  1. 김상일 (1999). 선체 구조의 용접변형 제어법 개발, 울산대학교 공학박사 학위논문
  2. 김상일 (2003). "FPSO선 Moon Pool 구조의 용접변형 해석에 관한 연구", 한국해양공학회지, Vol 17, No 3, pp 27-32
  3. 이주성과 박재우 (2008). "박판 필릿 용접 시 변형 제어를 위한 장력법 적용", 한국해양공학회지, Vol 22, No 1, pp 64-69
  4. Fujita, Y. and Nomoto, T. (1972). "Studies on Thermal Elasto-plastic Problems (1st Report)", Journal of the Society of Naval Architects of Japan, Vol 130, pp 183-191
  5. Kim, S.I., Han, J.M., Cho, Y.K., Kang, J.K., Lee, J.Y. and Lee, J.S. (1997). "A Study on the Accuracy Control of Block Assembly in Shipbuilding - Simulation of Residual Deformation Due to Fillet Welding -", Proceedings of ICCAS-1997, pp 367-381
  6. Lee, S.G. (1992). Modeling of Residual Stress in Thick Section Weldments, Ph.D. Thesis, Department of Welding Engineering, University of Ohio State
  7. Ueda, Y. and Yamakawa, T. (1973). “Analysis of Thermal Elastic-plastic Behavior of Metals During Welding by Finite Element Method“, Journal of the Japanese Welding Society, Vol 42, No 6, pp 567-577 https://doi.org/10.2207/qjjws1943.42.567
  8. Ueda, Y., Kim, Y.C., Yamakita, T. and Bang, H.S. (1988). "Applicability of Substituting Plane-deformation Problems for Three-dimensional Thermal Elasto-Plastic Problems", Transactions of the Japanese Welding Society, Vol 6, No 1, pp 47-59 https://doi.org/10.2207/qjjws.6.47
  9. Ueda, Y., Murakawa, H., Gu, S.M., Okumoto, Y. and Kamichika, R. (1992). 'Simulation of Welding Deformation for Accurate Ship Assembling (1st Report)', Journal of the Society of Naval Architects of Japan, Vol 171, pp 395-404