Journal of Welding and Joining

  • 제13권2호
  • /
  • Pages.122-131
  • /
  • 1995
  • /
  • 2466-2232(pISSN)
  • /
  • 2466-2100(eISSN)
대한용접접합학회 (The Korean Welding and Joining Society)
권호 표지

Cu를 함유한 HSLA강의 미세 조직과 인성에 미치는 냉각 속도의 영향

Effect of cooling rate on the microstructure and impact toughness of Cu-bearing HSLA steels

  • 발행 : 1995.06.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

The effects of cooling rate on the microstructures, precipitation of Cu-cluster, .epsilon.-Cu and impact toughness of high strength low alloy(HSLA) steel were studied using hardness tester, impact tester, DSC(differential scanning calorimetry), AES(auger electron spectroscopy) and TEM(transmission electron microscopy). Not only the Cu-precipitates but also the segregation of Cu, As, Sb, P, S, N, Sn along grain boundary were not observed at the specimens heat treated from 800.deg. C to 300.deg. C with the cooling time of 12-125 sec. The Cu-cluster, .epsilon.-Cu are formed by introducing ageing after cooling and the effect of precipitates on hardening increase after cooling was the same in all cooling rate. The peak hardness was obtained at an ageing of 500.deg. C in all cooling conditions. The impact energy become higher as the cooling time increases. This fact can be explained to be due to the tempering effect applied on the cooling stage since the present alloy has a relatively high Ms temperature and the local high concentration of the retained austenite.

키워드

참고문헌

  1. Advances in welding science and Technology, Conf. proc. Post weld heat treatment cracking in A710 HSLA precipitation strengthened steel C.D.Lundin;R.menon;Z.Chen;S.A.David(ed.)
  2. Welding Journel v.68 no.4 Stress-relief cracking of a Cu-containing HSLA-steel J.P.Balaguer;Z.Wang;E.P.Nippes
  3. Proc. Int, conf, on the Metallurgy, welding and Qualification of Microalloyed(HSLA) steel weldment: AWS Fundmental studies of the metallurgical causes for reheat cracking in 2 1/4Cr-1Mo, 1 1/4Cr-1/2Mo and copper precipitation hardenable steels and means of mitigating the potential problem C.D.Lundin;K.K.Khan;T.P.S.Gill
  4. 溶接 冶金學 松田福
  5. Proc. of the Int, conf, on Processing Microstructure and Properties and Microalloyed and other Modern High Strength Low Alloy Steels Microstructure-properties investigation of quenched and tempered HSLA-100steel R.P.Foley;M.E.Fine;DeArdo(ed.)
  6. Proc. of the Int, conf, on Processing Microstructure and Properties and Microalloyed and other Modern High Strength Low Alloy Steels Structures-properties studies of Cu-containing HSLA-100 steel M.Mujahid;A.K.Lis;C.I.Garcia;A.J.DeArdo
  7. Proc. of the Inter, Sympo. on Low-carbon steels for the 90's Toughness and fracture of ultra-low carbon plate steels S.M.Pytel;C.I.Garcia;A.J.DeArdo;R.Asfahani(ed.);G.Tither(ed.)
  8. 한국재료학회 v.5 no.3 Cu를 함유한 HSLA강의 기계적 성질에 미치는 열처리의 영향 박태원;심인옥;김영우;강정윤
  9. 대한 금속학회 v.33 no.1 열 분석법에 의한 Cu를 함유한 HSLA 강의 시효 거동에 관한 연구 박태원;심인옥;김영우;강정윤
  10. Recent trend in Welding science and Technology Microstructure and properties of a copper-precipitation strengthened HSLA weldment J.M.B.Losz;K.D.Challenger;S.A.David(ed.);J.M.Vitek(ed.)