• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.85.2-85
• /
• 2001

In this paper, we propose a modified Ziegler-Nichols PID controller using the fuzzy logic system. The proposed method is to parameterize a Ziegler-Nichols formula with a single parameter, and use the fuzzy logic system for automatic tuning of a single parameter of the modified Ziegler-Nichols formula. The fuzzy logic system has simple nine control rules. In order to verify the effectiveness of the proposed method, we simulated with the servo system. Simulation results demonstrate that better control performance can be achieved when compared with that of the Ziegler-Nichols PID controller.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1998.03a
• /
• pp.43-46
• /
• 1998

This paper presents a new parameter tuning method for PID controller. The Ziegler-Nichols Parameter tuning has been widely known as a fairly heuristic method to good determine setting of PID controllers, for a wide range of common industrial processes It has a excessive overshoot in the set point response, set point weighting can reduced the overshoot to specified values. It will also be shown that set point weighting is superior to the conventional solution of reducing large overshoot by other method. In this paper, we will modified the Ziegler-Nichols tuning formula by fuzzy set. These method will give appreciable improvement in the performance of PID controllers.

• Journal of Power System Engineering
• /
• v.21 no.2
• /
• pp.20-26
• /
• 2017

This study was carried out to investigate the effect of precipitate on the high temperature deformation stability of incoloy 825 alloy. $Cr_{23}C_6$ carbide was precipitated under $950^{\circ}C$, but was not detected over $1,000^{\circ}C$. Most of the precipitation consist of $Cr_{23}C_6$ carbide. Strain-rate sensitivity was the highest in 0.01/s and the lowest in 10/s. Strain-rate sensitivity was decreased sharply below $950^{\circ}C$. In the temperature between $850^{\circ}C{\sim}1,150^{\circ}C$, plastic instable area did not exist. It showed the lowest Ziegler Parameter value of 0.06 Ziegler Parameter was the lowest as 0.06 at $850^{\circ}C$ with 10s-1 of strain. The highest Ziegler Parameter value(0.43) was found in plastic deformation at $1,050^{\circ}C$ with 0.01s-1 of strain. It tends to have an higher resistance to the high temperature deformation under $950^{\circ}C$, due to the precipitation.

• Proceedings of the KIEE Conference
• /
• 1998.07b
• /
• pp.775-777
• /
• 1998

The Ziegler-Nichols parameter tuning has been widely known as a fairly heuristic method to good determine setting of PID controllers, for a wide range of common industrial processes. We extract process knowledge required for rule base controller through tuning experiment and simulation study, such as set point weighting and normalised gain and dead time of process. In this paper, we presents a rule base PID controller by extracted process knowledge and the modified Ziegler-Nichols tuning. Computer simulation are provided demonstrate the feasibility of this approach.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.3
• /
• pp.131-138
• /
• 1999

Generally, the digital controller has many advantages such as high precision, robustness to electrical noise, capability of flexible programming and fast response to the load variation. In this study, we have established proper mathematical equivalent model of Brushless DC (BLDC) motor and estimated the motor parameter by means of the back-emf measurement as being the step input to the controlled target BLDC motor. And the validity of proposed estimation method is confirmed by the test result of step response. As well, we have designed the reasonable digital controller as a consequence of the root locus method which is obtained from the open-loop transfer function of BLDC motor with hall sensor, and the determination of control gain for variable speed control. Here, revised Ziegler-Nichols tuning method is applied for the proper digital gain establishment, and the system stability is verified by the frequency domain analysis with Bode-plot and experimentation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.2
• /
• pp.219-225
• /
• 2002

Parameter tuning methods by Ziegler-Nichols for PID controllers are generally classified into Z-N(1) and Z-N(2). The purpose of this paper is to describe what relations exist between the methods of Z-N(1) and Z-N(2), or how Z-N(1) can be originated from Z-N(2) by analyzing one loop control system composing of P or PI controller and time delay process. In this paper, for the first step to seek mutual relations, the simple formulas of Z-N(2) are transformed into those composing of the same parameters as Z-N(1) which is derived from the analysis of frequency characteristics. Then, the approximation of the actual ultimate frequency is proposed as important premise in the translation between Z-N(1) and (2). Such equalization and approximation brings a simple approximated formula which can explain how Z-N(1) is originated from the Z-N(2) in the form of formula.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.3
• /
• pp.293-300
• /
• 2007

The aim of this paper is to design a speed controller of a DC motor by selection of a PID parameters using genetic algorithm. The model of a DC motor is considered as a typical non-oscillatory, second-order system, And this paper compares three kinds of tuning methods of parameter for PID controller. One is the controller design by the genetic algorithm. second is the controller design by the model matching method third is the controller design by Ziegler and Nichols method. It was found that the proposed PID parameters adjustment by the genetic algorithm is better than the Ziegler & Nickels' method. And also found that the results of the method by the genetic algorithm is nearly same as the model matching method which is analytical method. The proposed method could be applied to the higher order system which is not easy to use the model matching method.

• Journal of the Institute of Convergence Signal Processing
• /
• v.4 no.4
• /
• pp.52-57
• /
• 2003

A PID parameter tuning method was presented by the fuzzy singleton inference, based on step response-shaping of plant and experience knowledge of expert. The parameter-tuning has tow levels. The higher level determines modified coefficients for the controller based on operator's tuning know-how for characteristics of plant which can not be modeled. The lower level determines specified coefficients based on characteristics of response by Ziegler-Nickel's bounded sensitivity method. The last level parameters tuning of a PID controller is adjusted which the modified and specified coefficients makes adjustment rule, and is adjusted the proper value to each parameters by fuzzy singleton inference. Moreover, proposed the tuning method can reflex exporter knowledge and operator's tuning know-how and fuzzy singleton inference is rapidly operated.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.1
• /
• pp.129-137
• /
• 2017

In this paper, we propose a digital controller design methodology for an LLC resonant converter which has been widely used due to the advantages of low switching loss and high efficiency. We establish a mathematical model of an LLC resonant converter using the extended describing function concept and propose a controller design method based on the Ziegler Nichols control parameter tuning criteria. The voltage controller of an LLC resonant converter is designed based on the derived small signal model and the performance of the controller is verified by MATLAB simulations. The validity and the control performance of the designed voltage controller for the LLC resonant converter is analyzed through some simulations for the case of load variations and circuit modeling errors.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.11a
• /
• pp.112-119
• /
• 2001

Parameter tuning methods by Ziegler-Nickels for control systems are generally classified into Z-N(1) and Z-N(2). The purpose of this paper is to describe what relations exist between methods of Z-N(1) and Z-N(2), or how Z-N(1) method can be originated from Z-N(2) method by analyzing one loop control system of P or PI controller and time delay process. The formulas of Z-N(1) consist of process parameters, L(time delay), $K_m$(gain) and $T_m$(time constant), but Z-N(2) method is based only on the ultimate gain $K_u$ and the ultimate period $T_u$ acquired normally by practical trial without any parameters of Z-N(1). In this paper, for the first step to seek mutual relations, the simple formulas of Z-N(2) are transformed into the formulas composed of the same parameters as Z-N(1) which is derived from the analysis of frequency characteristics. Then, the approximation of the actual ultimate frequency is proposed as important premise in the translation between Z-N(1) and (2). Such equalization and approximation brings a simple approximated formula which can explain how Z-N(1) is originated from the Z-N(2) in the form of formula. And a model system is adopted to compare the approximated formula to Z-N(1) and Z-N(2) methods, the results of which show the effectiveness of the proposals.