• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.7 no.2
• /
• pp.1-8
• /
• 1987

Recently, as subway traffic have been increased, vibration of each parts of subway influence on structures above subway tunnel. This paper presents a new method to reduce which was generated by subway traffic. By comparing directional coherence relationship of X, Y, Z-axis and vibrational coherence relationship of spherical signal which was unified by three directional signals, effective vibration diminishing method was proposed. It can be found that locomotive vibration(specially 1-2Hz) have the worst effect on the vibration of structures and the vibration of subway box ranked 2nd, the vibration of earth ranked 3rd.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.2
• /
• pp.142-149
• /
• 2004

PMLSM(Permanent Magnet linear Synchronous Motor) has widely applied to industrial automations, machine tools and semiconductor equipments due to the merit on the reduction of noise, vibration and the superior dynamic characteristics in comparison to the conventional method, which uses mechanical transfer equipments. Especially, in the case of applying to Z-axis operation structure, control system needs the method of an initial angle setting and the improvement of up/down operation characteristics. This paper proposes an initial angle setting algorithm and a variable gain schedule using real speed and moving direction to improve up/down operation characteristics. The effectiveness of proposed algorithms Is demonstrated by comparing to a conventional gain system via 4-point absolute positions profile with each velocity, acceleration and deceleration.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.10
• /
• pp.1011-1016
• /
• 2015

Gas piping systems in power plants and factories are always influenced by the mechanical vibrations of rotational machines such as pumps, blowers, and compressors. Unusual vibrations in a gas piping system influence possible leakages of liquids or gases, which can lead to large explosive accidents. Real-time measurements of unusual vibrations in piping systems in situ prohibit them from being possible leakages owing to the repeated fatigue of vibrations. In this paper, a non-contact 3-dimensional measurement system that can detect the vibrations of a solid body and monitor its vibrational modes is introduced. To detect the displacements of a body, a stereoscopic camera system is used, through which the major vibration types of solid bodies (such as X-axis-major, Y-axis-major, and Z-axis-major vibrations) can be monitored. In order to judge the vibration types, an artificial neural network is used. The measurement system consists of a host computer, stereoscopic camera system (two-camera system, high-speed high-resolution camera), and a measurement target. Through practical application on a flat plate, the measured data from the non-contact measurement system showed good agreement with those from the original vibration mode produced by an accelerator.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.709-714
• /
• 2017

Structures like bridges or buildings need to be checked continuously to diagnose their safety. However, it is extremely difficult for the people who access such structures to check all areas directly. To overcome this problem, there is a lot of active research into structural health monitoring (SHM) with wireless sensor nodes (WSNs). In this paper, for more accurate checking of SHM with WSNs, we experimentally compare and evaluate the performance of Xenomai, which provides real-time processing under the traditional Linux kernel. For this purpose, we patch Xenomai into the traditional Linux kernel of a commercial embedded board, Raspberry Pi, and implement a task that periodically reads vibration data of the z-axis from an accelerometer in order to analyze the natural frequency of cantilever beams. Reading the data from the traditional Linux kernel with the same method, we analyze the natural frequency of the cantilever beams using Smart Office Analyzer. Finally, to review the validity of Xenomai for WSNs, we obtain vibration data on the z-axis from the accelerometer via wired network and compared and analyzed them the same way.

• Journal of Biosystems Engineering
• /
• v.29 no.2
• /
• pp.101-108
• /
• 2004

The objectives of this study were to determine the natural frequency of a walking-type cultivator's handle using a modal analysis, to determine whether or not the handle resonates with forcing frequency induced by its engine, and to determine a method to reduce the handle vibration using a technique of the operational deflection shapes(ODS). Results of the study are as follows: The natural frequencies of the handle up to third harmonics were found to be 20.4, 22.5 and 92.1 Hz in the vertical direction and 14.9, 93, and 132 Hz in the horizontal direction. It was found that the handle does not resonate with the forcing frequency of the engine, which is 52 Hz. The operational deflection shape analysis revealed the deflected shapes of the handle in the vertical and horizontal directions and suggested that the handle vibration can be reduced by adding some mass to the place where the largest deflection occurs. Attaching of 1.1 kg mass adjacent to the largely deflected area resulted in reductions of vibration from 9.45 to 8.03 m/s$^2$ in x-axis direction from 3.89 to 3.16 m/s$^2$ in y-axis direction and from 7.89 to 3.09 m/s$^2$ in z-axis direction, which are respectively 15, 19 and 61% reductions. The total vibration level was reduced by 29%, indicating that mass-adding method by the ODS is very effective for reducing the handle vibrations of the cultivators.

• Journal of the Ergonomics Society of Korea
• /
• v.19 no.2
• /
• pp.75-86
• /
• 2000

In this study, the characteristics of transmitted vibration on HAS(hand-arm system) were identified to evaluate physical load due to the work surface orientation, tool weight and push force during powered drilling tasks. The characteristics of transmitted vibration on work surface orientation showed that the acceleration of transmitted vibration on horizontal work surface was higher than that on the vertical work surface. Regarding the characteristics of transmitted vibration on tool weight, the vibration acceleration level becomes lower as the tool weight becomes heavier. The amount of transmitted vibration on hand-arm system was decreased down to the tool weight of 2.4kg. However, as the tool weight becomes heavier than 2.8kg, the amount of transmitted vibration was increased and had peak value at 3.2kg of tool weight. Regarding the characteristics of transmitted vibration on push force, the vibration acceleration level goes higher, as the push force becomes larger. The characteristics of transmitted vibration on the axis of vibration showed that the direction of $Z_h$ had the highest acceleration compared to the direction of $X_h$, and $Y_h$. The direction of $X_h$, $Y_h$ and $Z_h$ had the highest acceleration of transmitted vibration on the hand, wrist and elbow, respectively. The results of this study showed that the condition which affect the lowest physical load to the subject on the powered drilling task would be working with the 2.4kg of tool weight on the vertical work surface.

• Journal of the Korean Society of Safety
• /
• v.24 no.1
• /
• pp.60-68
• /
• 2009

The aim of this paper is to evaluate the compatibility of anti-vibration gloves, to predict the attenuation of vibration with different types of anti-vibration gloves, to estimate the spectra of the ISO 10819 standard, and to present an oscillating spectrum adequate for vibrating tools. This paper use two ISO standards for the measurement and evaluation of hand-arm vibration. Some anti-vibration gloves can attenuate vibration, but all the anti-vibration gloves in this study do not satisfy the ISO 10819 requirements. In case of equal vibration types, the outside materials are effective in order of leather, fabrics and rubber-coating. Anti-vibration gloves manufactured in the United State satisfy ISO 10819 criteria using United State subjects, but do not satisfy ISO 10819 using Japanese subjects. M-spectrum acceleration exists below 10Hz and H-spectrum exists above 500Hz. Generally vibrating tools have the peak of Z-axis, but generation of vibration differ from each vibrating tools.

• Journal of Sensor Science and Technology
• /
• v.26 no.4
• /
• pp.235-238
• /
• 2017

In this study, the design of a tri-axis micromachined gyroscope is proposed and the vibration characteristic of the structure is analyzed. Tri-axis vibratory gyroscopes that utilize Coriolis effect are the most commonly used micromachined inertial sensors because of their advantages, such as low cost, small packaging size, and low power consumption. The proposed design is a single structure with four proof masses, which are coupled to their adjacent ones. The coupling springs of the proof masses orthogonally transfer the driving vibrational motion. The resonant frequencies of the gyroscope are analyzed by finite element method (FEM) simulation. The suspension beam spring design of proof masses limits the resonance frequencies of four modes, viz., drive mode, pitch, roll and yaw sensing mode in the range of 110 Hz near 21 kHz, 21173 Hz, 21239 Hz, 21244 Hz, and 21280 Hz, respectively. The unwanted modes are separated from the drive and sense modes by more than 700 Hz. Thereafter the drive and the sense mode vibrations are calculated and simulated to confirm the driving feasibility and estimate the sensitivity of the gyroscope. The cross-axis sensitivities caused by driving motion are 1.5 deg/s for both x- and y-axis, and 0.2 deg/s for z-axis.

• Journal of KSNVE
• /
• v.10 no.5
• /
• pp.811-818
• /
• 2000

This paper deals with the design of a car seat for enhancing dynamic ride quality using a Biomechanical Model that was developed from the measured whole-body vibration characteristic. For evaluation of seat ride quality, the z-axis acceleration of floor as an input of biomechanical model was measured on a driving passenger car at highway and national road. Form the floor signal and the estimated biomechanical model, overall ride value evaluated by parameter study of seat stiffness and damping. The result shows that overall ride value decreases as the seat damping increases and the sear stiffness decreases. A lot of polyurethane foams were manufactured and tried to evaluate dynamic ride quality of a seat. It is found that stiffness and damping of a seat show a linear relationship, which means the stiffness and damping are not independent each other, So the optimal seat parameters within practically achievable space are determined.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.309-313
• /
• 2006

Many researchers have studied on the lightness of automobile. These researches are such as a body shell, sub frame, fuel tank, engine etc. The transmission Part is a magnitude one in the aspect of weight. A drive shaft (propeller shaft) transmits the engine power to rear differential gear assembly. It is used in the compact car that is a single drive shaft. But in the case of long body cars such as SUV (Sports Utility Vehicle), truck and large vehicle, two or three divided drive shaft are used to prevent the vibration damage from a drive shaft that has been taken high torsion and rotation. This multi-divided drive shaft structure is so heavy because it is assembled by yoke, center bearing and solid spline axis. When the rear axle move up and down, the spline shaft adjust the variation of a length between the transmission and rear axle gearbox. In this paper, it is studied in the experimental method that is a bending vibration characteristic of slip in tube shaped propeller shaft. This type propeller shaft is developed to combine the spline axis with drive shaft and can be light in weight of transmission part.