• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.632-638
• /
• 2002

Electron beam (EB) and Gas tungsten arc (TIG) welds were performed on 12.7 mm thick Ti-6Al-4V plate (ASTM Titanium Grade 5). Charpy-V toughness and hardness, as well as, microstructure of the welds and penetration from the macrostructure were studied. It appears that by EB welding rather smaller $\beta$-grains than with TIG welding can be obtained. Next to the fusion line the $\beta$-grain size in the HAZ was 50 ${\mu}{\textrm}{m}$l while in the weld metal it was 150 ${\mu}{\textrm}{m}$. Charpy-V toughness of the EB weld metal was equal or even better to that of base metal, which shows that the $\alpha$-martensite per se is not particularly brittle if only the grain size is fine enough. This is similar to behavior of low carbon martensite in steel. The grain size was studied with light optical and scanning electron (SEM) microscopes. Thus for products, for products which can be manufactured automatically with very narrow fit, the EB welding of Ti-6Al-4V appears to yield satisfactory toughness without any complex post weld heat treatment. ill this study as in earlier studies the TIG welds gave lower toughness than that of the base material due to the higher heat input and slower cooling as compared to EB welding.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.408-411
• /
• 2002

Effect of in-situ vibration on the properties of A-grade steel SMA weldment has been investigated. Welding was performed on the steel fixed at the experimental jig under the mechanical vibration of a given frequency. The applied frequency varied from 39 to 43.5 Hz (harmonic frequency). For weldments formed under the vibration with a sub-harmonic frequency, both the columnar width of the weld metal and the prior austenite grain size of the HAZ near the fusion line clearly decreased. This indicates that the vibration increase the cooling rate after welding. Vibration effect was also found at the weld metal formed at the center region of the weldment. The weld metal showed liner microstructure both in columnar zone and in equiaxed zone with thinner grain boundary ferrite. However mechanical properties of the weld metal did not exactly follow the microstructural changes developed under the vibration. The weld metal formed under the vibration revealed higher yield and tensile strength but lower ductility and impact toughness, compared with the conventional weld metal.

• Korean Journal of Materials Research
• /
• v.27 no.9
• /
• pp.477-483
• /
• 2017

This present study deals with the microstructure and tensile properties of 600 MPa-grade high strength and seismic resistant reinforcing steels. The high strength reinforcing steel (SD 600) was fabricated by Tempcore processing, while the seismic resistant reinforcing steel (SD 600S) was air-cooled after hot-rolling treatment. The microstructure analysis results showed that the SD 600 steel specimen consisted of a tempered martensite and ferrite-pearlite structure after Tempcore processing, while the SD 600S steel specimen had a fully ferrite-pearlite structure. The room-temperature tensile test results indicate that, because of the enhanced solid solution and precipitation strengthening caused by relatively higher contents of C, Mn, Si and V in the SD 600S steel specimen, this specimen, with fully ferrite-pearlite structure, had yield and tensile strengths higher than those of the SD 600 specimen. On the other hand, the hardness of the SD 600 and SD 600S steel specimens changed in different ways according to location, dependent on the microstructure, ferrite grain size, and volume fraction.

• Resources Recycling
• /
• v.10 no.6
• /
• pp.43-52
• /
• 2001

This study was conducted to obtain granular crystalline gypsum that can be used as raw material for Plaster boards or cements from waste Plaster board. Gypsum could be Preferentially disintegrated to gypsum needle in $10\mu\textrm{m}$ or less size by hydration after the dehydration of crushed waste Plaster board. The finer the gypsum needle, it is easier to remove coarse impurities and to recover the gypsum needle. The optimum conditions for obtain the finer gypsum size were dehydration rate of 75~85%, solid concentration at hydration of 10~15%, agitation speed of 250~400 rpm, crushing size before dehydration of 2 cm or less. Gypsum of 98.21% grade was recovered with 99.0% yield as the undersize of 325 mesh wet screening followed by the dehydration-hydration process performed at the conditions of dehydration rate of 80%, solid concentration at hydration of 15%, agitation speed of 300 rpm, crushing size before dehydration of 2 cm or less. After the recrystallization of recovered gypsum, Plate-like gypsum of $151\mu\textrm{m}$ size with 99.49% grade was obtained as the oversize of 270 mesh in a wet screening.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.37 no.1 s.109
• /
• pp.17-24
• /
• 2005

The increase of using low grade ace, the unsorted mixed grade, as fibrous raw materials for the packaging paper results in the increment of fine screen reject owing to the strong tendency to reduce the slot width. Since the most of screen reject consists of undispersed fiber flake, the suitable treatment of the flake could increase the yield of ace recycling and decrease the amount of solid waste. In this work, the novel method combined the mild mechanical treatment by using Tumbling pulper with the biological treatment was developed and applied to the wet strength flake and the fine screen tail line reject originated from a packaging paper mill. The results showed the new method could provide much better efficiency for the disintegration of undispersed flake and for the recovery of fiber from the rejects. The application of the laboratory scaled-Pack pulper showed the possible separation technique for mill application by fractioning effectively the fiber from the treated solid waste.

• Journal of Ocean Engineering and Technology
• /
• v.1 no.2
• /
• pp.113-122
• /
• 1987

Ships and offshore strrctures are exposed to the corrosive surroundings, and the extablishment of the design criteria and the elucidation on the influence by this environment are requested to maintain the safety and to demonstrate the function of the structure. In this paper, the fatigue-crack-growth behavior on the compact tension specimens of quenched, tempered HT80 grade steels and RA36 high tensile steels having a single edge fatigue cracked notch respectively, were investigated under the repeated tensile stress with constant stroke in sea water for the welded parts by shielded metal arc welding. Main results obtained are summerized as follows; 1. The fatigue-crack-growth rates da/dN in sea water appeared to be greater behavior than those in air environment at the same stress intensisy factor range $\DeltaK$. 2. The correlation data of da/dN$\DeltaK$ of the two kinds of high tensile steels in sea water showed no great difference, however, the correlation data of da/dN$\DeltaK/\sigma_y$($\sigma_y$ stands for yield strength of the material) showed that the fatigue-crack-growth behavior of RA36 plate is affected by active path corrosion(APC) mechanism, while that of HT80 grade plate is mainly affected by hydrogen embrittlement mechanism.

• Steel and Composite Structures
• /
• v.38 no.6
• /
• pp.705-716
• /
• 2021

An innovative partially precast partially encased composite beam (PPECB) is put forward based on the existing research. In order to study the flexural performance of the new composite beam which has precast part and cast-in-place part, six prefabricated specimens and one cast-in-place specimen are designed with considering the influence of the production method, the steel flange thickness, the concrete strength grade and the stirrup process on the behavior of the composite beam. Through four points loading and test data collection and analysis, the behavior of partially prefabricated specimen is similar to that of cast-in-place specimen, and the casting method, the thickness of the steel flange, the concrete strength grade and the stirrup process have different influence on the crack, yield and peak load bearing capacity of the component. Finally, the calculation theory of plastic bending of partially precast partially encased concrete composite beams is given. The calculation results are in good agreement with the experimental results, which can be used for practical engineering theory guidance. This paper can provide reference value for further research and engineering application.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.20 no.1
• /
• pp.66-74
• /
• 2024

This study investigates the effects of temperatures and strain rates on the strength and ductility of Gr.91 (ASME Grade 91) steel which is widely being used as a heat-resistant material in Generation IV nuclear and super critical thermal power plants. The tensile behavior of modified 9Cr-1Mo (Gr.91) steel was studied for the three strain rates of 6.67×10^-5/s, 6.67×10^-4/s and 6.67×10-3/s over the temperature range from room temperature (RT) to 650℃. Experimental results showed that at specific combinations of temperatures (300~400℃) and strain rates, serrations appeared in the stress-strain curves. Concurrently, abnormal behaviors such as a plateau in yield strength and tensile strength, a minimum in ductility and negative strain rate sensitivity were observed. These phenomena were analyzed as significant characteristics of dynamic strain aging (DSA). Since this abnormal behavior in Gr.91 steel affects the material strength, it is judged that a correlation analysis between DSA and material strength should be crucial in the design and integrity evaluation of Gr. 91 steel pressure vessel and piping subjected to high-temperature loading.

• Korean Journal of Organic Agriculture
• /
• v.17 no.3
• /
• pp.347-356
• /
• 2009

In attempt to select the most appropriate forage legume species, this study was conducted on the 10 forage legume crops suitable for the central region of Korea and investigated their productivity, feed values and stock carrying capacity. In the results, red clover showed fresh matter yield 38.6 ton/ha, dry matter yield 7.8 ton/ha, crude protein yield 1.0 ton/ha, total digestible nutrients(TDN) yield 4.6 ton/ha, its fresh matter yield, dry matter yield and nutrient yield were significantly(p<0.05) higher than other species. The value of neutral detergent fiber(NDF) and acid detergent fiber(ADF) were getting higher by the late harvest time then galega and cicer milkvetch were the highest and yellow suckling clover was the lowest value. Relative feed value(RFV) showed good feed values above 100 except cicer milkvetch and galega. In terms of feed grading, yellow suckling clover, yellow blossom sweet clover, crimson clover, hairy vetch were classified into 1st grade, above 151%. The average stock carrying capacity was yet high Kcp(2.18 head/ha/yr), KTDN(1.25 head/ha/yr) and K(0.04 head/ha/yr). Especially, red clover had the highest stock carrying capacity, Kcp 6.84 head/ha/yr, KTDN 3.64 head/ha/yr and K 0.05 head/ha/yr. According to results, red clover is considered to be the most appropriate crops for the central region, in terms of quality, feed value and stock carrying capacity.

• Korean Journal of Medicinal Crop Science
• /
• v.5 no.1
• /
• pp.1-6
• /
• 1997

The experiment was conducted to investigate the effect of water stress on yield and quality of Ligusticum chuanxiong Hort. The water stress treatment was imposed artificially on seedling, flowering and rhizome enlargement stage of the plant. The root yield rate decreased to 19.1%, 18.2% and by the water stress treatment at rhizome enlargement, seedling and flowering stage, respectively. Portion of the products having commercial quality grade (above 20g of rhizome weight) was 93.4% at control plot, while it was 85%, 81.7% and 78.3% when stressed for water at seedling, flowering and root enlargement stage, respectively. Content of extract was the higher in the order of control, water stressed at rhizome enlargement, flowering and the seedling stage. Postive correlationship was found between yield of rhizome and rootlet yield or economic production ratio, and between dry weight of stem and rootlet yield.