• Journal of Environmental Health Sciences
• /
• v.46 no.5
• /
• pp.555-564
• /
• 2020

Objectives: To identify and investigate through qualitative and quantitative analysis the hazardous substances generated when compressed wood was burned at a live fire-training center. Methods: Four types of compressed wood that are actually used in live fire training were burned in a chamber according to KS F2271. The gaseous material was sampled with a gas detector tube and conventional personal samplers. Results: 1,3-butadiene, benzene, toluene, xylene, formaldehyde, hydrogen chloride, hydrogen cyanide, ammonia, carbon monoxide, and nitric acid were detected. In particular, 1,3-butadiene (497.04-680.44 ppm), benzene (97.79-125.02 ppm), formaldehyde (1.72-13.03 ppm), hydrogen chloride (4.71-15.66 ppm), hydrogen cyanide (3.64-8.57 ppm), and sulfuric acid (3.85-5.01 ppm) exceeded the Korean Occupational Exposure Limit as measured by sampling pump according to the type of compressed wood. Conclusions: We found through the chamber testing that firefighters could be exposed to toxic substances during live fire training. Therefore, firefighter protection is needed and more research is required in the field.

• Korean Journal of Plant Resources
• /
• v.22 no.4
• /
• pp.293-298
• /
• 2009

We prepared densified wood pellet by agricultural waste. The hemp woody core was used as replacing wood resource. Hemp was separated into the bast fiber and the woody core by hot steaming treatment. The hemp woody core had a similar lignin content(19.4%) and carbohydrate composition with hardwood(20-25% lignin in hardwood), respectively. Also, the hemp had a low ash content(0.5%), which resulted in a low ash formation in pellet burning. Heating value of the hemp pellet(18.40 MJ/kg) had a very similar to the pellet made by hardwoods. The hemp woody core could be replaced the hardwood for densified wood pellet.

• Journal of the Korean Wood Science and Technology
• /
• v.10 no.3
• /
• pp.152-164
• /
• 1982

1. In order to make the improvement of plywood quality, this study has been made. The pretreatments applied to the veneers are as follows. a) The soaking treatment of the veneer in 30 percent methanol solution for 24 hours was applied to remove some resinous materials which may cause many stain discolouring on the face of finished plywood. b) The preservative treatment of the veneer in 2 percent malenit solution for 2 to 3 minutes was adopted to make resistance against decay and insect damages. c) The fire retardant treatment of the veneer in 40 percent ammonium phosphate solution for 2 hours was applied to give retardation effect against fire burning. 2. The results summarized in this study are as follows. a) One percent resinous materials was extracted, after the soaking of the veneers in 30 percent diluted methanol. b) No marks of the dirty stains of resinous materials on the face of the treated plywood was shown, although many quite dirty stains on the face of untreated plywood have contrary seen. c) However, the strip shear test strength of the treated plywood was not decreased. It means that there is no difference in the strength between the treated plywood and the untreated plywood. The strength values were 25.08 kg/$cm^2$ and 24.98 kg/$cm^2$, respectively. d) The strip shear test strength of plywood made of the treated veneers in 2 percent malenit solution was not decreased. e) The slight decrease of the strip shear test strength of the treated plywood made of the treated veneer in 40 percent ammonuim phosphate solution was shown. However, the remarkable difference of the fire retardation activities between the treated specimens and the untreated specimens has seen as in Table 10, that is, the fire proofed specimens had taken about 28 seconds to start to burn, while the untreated specimens had taken 15 seconds to reach to burning. This means that the fire retardation effect of the fire proofed plywood was greater than that of the unproofed plywood.

• Journal of Korean Society for Atmospheric Environment
• /
• v.8 no.3
• /
• pp.179-190
• /
• 1992

This study was carried out to characterize sources of atmospheric total suspended particulates (TSP) in urban and sub--urban areas of metropolitan taegu. The sources were tentatively identified by a multivariate technique, i.e. principal component analysis (PCA), and the source contributions to the atmospheric concentrations of TSP were further estimated by stepwise multiple regression analysis. A total of 5 sources was identified in the urban area of Taegu (soil dust resuspension, fuel combustion, secondary aerosol, traffic related aerosol, and refuge burning), while 4 sources were found to be significant in the sub--urban area as following: fuel combustion/secondary aerosol, soil dust resuspension, traffic related aerosol, and wood/agricultural burning. The largest contributor to the atmospheric TSP appeared to be the soil dust resuspension in both areas. The source apportionment of the extractable organic matter (EOM) was also carried out for the Taegu data. The EOM was determined with respect to the solvent polarity, i.e. cyclohexane (non-polar), dichloromethane (semi--polar), and acetone (polar). In addition, the source profiles for the TSP in Taegu area were estimated using a PCA-based algorithm, and the validity was evaluated tentatively by comparing the data in the literature.

• Fire Science and Engineering
• /
• v.31 no.5
• /
• pp.7-11
• /
• 2017

The purpose of this study is to recognize the necessity for the management of the available materials in cases of arsons and to prevent arson gaining an understanding of the combustion characteristics of the flammable materials and combustion accelerants in arson cases. We investigated and analyzed the statistical data on arsons and selected flammable materials (wood, paper, synthetic textiles, synthetic resins), and combustion accelerants (gasoline, diesel, solvent) that are frequently used in cases of arson. We conducted a thermogravimetric analysis to assess the thermal properties of the flammable materials. Also, we conducted burning and flame spread rate tests for the purpose of comparing and analyzing the combustion characteristics of the flammable materials and combustion accelerants.

• Journal of Conservation Science
• /
• v.28 no.2
• /
• pp.165-173
• /
• 2012

In this work, scientific and systematic analysis was conducted for finding out the methods and techniques of ancient ink stick making. Analysis the ancient ink stick on ancient documents and wooden writing as letter or painting, we concluded as followings. From the analysis of ancient wood by dendrochronology, wood was cut at 1899, which provided the information on the year of ink stick's made on writing on ancient wood. Single particle size for soot of ancient ink stick was 107 nm for ink on the roof-filling timber in Sinsunwonjeon of Changdeok Palace, compared to 38 to 86 nm on the letter on ancient 12 paper document. Aggregate particle size was 370 nm for ink on the roof-filling timber in Sinsunwonjeon of Changdeok Palace, but 206 to 318 nm for aggregate particle size on 12 paper documents. There was similar pattern between single particle size and aggregate particle size of soot, which might provide the information of raw material for ancient ink. From infra-red and Raman spectroscopic analysis of sheet of writing on paper or wood, there was severe interference from background material (paper or wood). From Raman spectroscopic analysis of ancient ink carefully separated from ancient wood, spectrum pattern was closer to ink stick made by the soot from pine burning.

• Environmental and Resource Economics Review
• /
• v.19 no.3
• /
• pp.597-632
• /
• 2010

There is general agreement that global warming is occurring and that the main contributor to this probably is the buildup of green house gasses, GHG, in the atmosphere. Two main contributors are the utilization of fossil fuels and the deforestation of many regions of the world. The burning of fossil fuels increases atmospheric carbon while the burning of fuel-wood reducing fossil fuel consumption along with its forest source maintain an atmospheric carbon level. The standing timber in the forests is a carbon sink, as are wood buildings and structures, and fossil fuel in the ground. This paper is designed to examine a number of current issues related to mitigating the global warming problem through forestry. For this purpose, we develop a modeling approach by integrating timber market, fossil fuel market and carbon cycling model. We use discrete time optimal control theory to identify optimal time paths, the laws of motion, and stationary stats solutions of endogenous variables in the model. On the basis of these results, we identify the optimal amounts of subsidies to be provided or taxes to be imposed by the regulatory agency to mitigate atmospheric carbon accumulation. We also present a numerical example to help illustrate the characteristics of variables in the model when the social cost for atmospheric carbon incrementally shifts upward. A surprising result is that the social cost function for atmospheric carbon has a very smaller impact on the optimal rotation period than previous literature suggested.

• Journal of the Korean Wood Science and Technology
• /
• v.40 no.1
• /
• pp.19-25
• /
• 2012

The fire retardant bamboo charcoal (BC) boards were manufactured for interior building materials in this study, The BC boards were manufactured by mixing and pressing of the bamboo charcoal, expanded vermiculite, and inorganic binder. The combustion behaviors of the BC boards were investigated using a cone calorimeter at an incident heat flux of 50 kW/$m^2$. Three building materials (plywood, BC board of Japan, and gypsum board) were used to observe the burning behaviors of weight loss, total heat release rate, and maximum heat release rate. Surface test and toxicity evaluation of the BC board were also conducted. The weight loss of the BC board (12.0%) was lower than the nonflammable gypsum board (15.6%) after burning of 10 min. Total heat release of the BC was 3 MJ/$m^2$ (KS standard 8 MJ/$m^2$) and total heat release rate of the BC was 20 kW/$m^2$ (KS standard 200 kW/$m^2$). Therefore, the BC boards were adjustable for the third-grade flame retardant building materials. External appearance change and mouse toxicity were not found in the BC boards after the combustion test.

• 한국문화재보존과학회:학술대회논문집
• /
• 2005.11a
• /
• pp.300-305
• /
• 2005

Tree-ring chronologies can be used to date historical buildings and furniture by matching them with the chronologies of living trees or previously dated samples. Tree-ring dating gives a calender year to each tree ring and produces the felling dates of logs or woods which had been used for buildings. In Korea, several chronologies of Japanese red pine(Pinus densiflora Sieb. et Zucc.,'sonamu' in Korean), a major species for the wooden building materials, have been developed and used for dating historical buildings. Daejojeon of Changduck Palace is known to be reconstructed in A.D. 1920 after burned-out in A.D. 1917. Instead of new woods, Daejojeon was reconstructed by reusing the woods of Kyotaejeon in Kyungbok Palace. We sampled total of 26 wood samples which were replaced during the repair process of Daejojeon in 1995. Felling dates of the samples were determined by the dendrochronological crossdating method. Crossdating method employs graphic comparison of the master patterns (ring-width plots of living trees or known dates) with those of the sample chronologies of unknown dates. The cutting dates of Daejojeon woods were divided in two groups. One was the late 1860s and the other 1880s. The results confirmed that Kyotaejeon was reconstruced first in the A.D 1860s and then in late 1880s after burning out in 1876.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.108.1-108.1
• /
• 2011

This paper proposes the method to develop the fuel of suljigemi pellets using agricultural by-products the occurred during the manufacturing of alcohol. This paper is the goal to make sulgigemi pellet fuel for develops pellet of high calorie. The methods of sulgigemi pellet manufacturing well mix as the dough with the water and the sulgigemi. And then we have dried in the after compression and molding using well mixed the sulgigemi. The moisture of pellets has dried it removed until about 85%. Suljigemi pellet has the effect of zero emission as the soil conditioner using ash after burning. The merits for the sulgigemi pellet are the convenience of storage and custody. Also sulgigemi pellet has the reduction effect of carriage fee, fuel economy and low-cost high-efficiency effects, environmentally clean fuel as CO2 emissions savings. In experiment, we confirmed to calories of the wood pellet and the sulgigemi pellet. The calorie of the suljigemi pellets has high 233 kilo calories than the wood pellets. So the technologies of the sulgigemi fuel pellets are developing low carbon, green growth renewable energy fuel through futuristic energy system will be.