• Journal of the Korean Wood Science and Technology
• /
• v.43 no.1
• /
• pp.60-67
• /
• 2015

In order to evaluate the bond performance of domestic larch glulam and the glass fiber reinforced plastic (GFRP) rod, the specimen with the GFRP rod bonded-in domestic larch glulam for pull-out test was produced. The test was carried out using various specimens with different gluing depth, width of glue-line and type of adhesive. The cantilever type rahmen structure specimen with bonded-in GFRP rods was produced based on the result of pull-out test, and its moment resistance performance was compared and examined with the moment resistance performance of slotted-in steel plate specimen. As a result of the pull-out test, the most excellent bond performance was found when the insertion depth of GFRP rods was 5 times larger than the diameter of GFRP rods. When the glue-line thickness was 1 mm, the bond performance improved by 17%~29% in comparison to the bond performance in the case of the glue-line thickness of 2 mm. Also, the bonded strength of the specimen used with poly-urethane adhesive was 2.9~4.0 times greater than the bonded strength of specimen used with resorcinol adhesive. The cantilever type rahmen structure specimen with bonded-in GFRP rods showed the moment resistance performance 0.82 times lower in comparison to the slotted-in steel plate specimen used with the drift pin, but the initial stiffness was similar as 0.93 times.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.4
• /
• pp.388-396
• /
• 2009

In our study, the potential of okara as an ingredient of new bio-based adhesives was investigated for the production of fancy-veneered flooring boards. Okara was hydrolyzed by 1% sulfuric acid solution (AC) and 1% sodium hydroxide solution (AK). Phenol formaldehyde (PF) prepolymers were prepared as a cross-linker of okara hydrolyzates. Then, okara-based adhesive resins were formulated with 35% AC, 35% AK and 30% PF prepolymer on solid content basis. The adhesive resins were applied on high-density fiberboards (HDF) with the spread rate of $300g/m^2$. After that, oak fancy veneers are covered on the HDF, and then pressed with the pressure of $7kg/m^2$ at $120^{\circ}C$. The experimental variables were three mole ratios of formaldehyde to phenol (1.8, 2.1, 2.4), three assembly time (0, 10, 20 min), and two press time (90 sec, 120 sec), respectively. The fancy-veneered high-density fiberboards were tested by dry tensile strength, glueline failure by wetting and formaldehyde emission. Tensile strength of the boards exceeded the requirement of KS standard. The formaldehyde emissions were approached at the E0 level specified in KS standard. Based on these results, okara can be used as an ingredient of environmentally friendly adhesive resin systems for the production of flooring boards.

• Journal of Applied Biological Chemistry
• /
• v.55 no.1
• /
• pp.55-59
• /
• 2012

We designed a new rapid detection method for volatilized formaldehyde from wood. The process was installed with volatilizing and collecting parts in an incubator. For rapid sampling of formaldehyde from wood, we pulverized the wood to sawdust, and used 0.15-2.0 mm particles for the tests. The highest sampling rate (94.8%) was obtained at 40 mL/min flow rate and $100^{\circ}C$. Under the optimized condition, we could collect the volatilized formaldehyde with good recovery rate. The developed method was applied to the monitoring of the formaldehyde from wood, and the measured concentrations were 0.7-4.6 ${\mu}g/g$ from natural wood, 5.9-12.3 ${\mu}g/g$ from preserved wood, and 5.9-211.5 ${\mu}g/g$ from chemical adhesive processed wood. From the results, we identified natural wood sawdust and chemically processed wood (medium density fiberboard, high density fiberboard, particle board) by the formaldehyde contents except preserved wood.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.4
• /
• pp.1-6
• /
• 1996

Extracts from bark have been studied with a view to producing water-proof wood adhesives. Lately many softwoods, such as radiata pine from New Zealand and larch from Siberia, Russia, have been imported and utilized, and their residual barks would be expecting as potential raw materials for something useful chemicals. The great effort toward utilization of bark extractives as a chemical feedstock has been made on a worldwide level. However few report has been done for the utilization of tree bark extractives in Korea. Hot-water extracts were prepared from barks of Japanese larch(Larix leptolepis). Siberian larch(Larix gmelinii) and Radiata pine(Pinus radiata). The effect of various factors, such as particle size, liquor ratio, extraction temperature, and reaction time, on the extractive yields was discussed. Particle sizes affected the hot-water extractives: the finer the particle size, the higher extractives and extract efficiency. Higher temperature and higher liquor ratio were more effective. Extractives from Japanese larch were relatively less than those from Siberian larch and Radiata pine barks. Formaldehyde precipitates was the highest in extractives of Radiata pine barks. It could be concluded that Siberian larch bark was the best raw material for tannin adhesives, because its extractive yield was higher than those of the other barks.

• Journal of the Korea Furniture Society
• /
• v.19 no.5
• /
• pp.319-327
• /
• 2008

As art of lamination by plywood got to be generally used, it became a suitable material for expressing live curves that were not able to be expressed on wood furniture made of plank and timber, as well as, openwork deep in curved space, heavy quality of material, and changing contour line-looking wave lines with different process angles. As an alternative, it would be good to build a full scale model, since it would provide practice in form-building and it would also provide a chance to correct the form. Less material can be used and reduce the cutting process by Properly trimming models made of soft formal structure such as Styrofoam Iso-pink and adhesive Styrofoam, and separating the layers and using them on shape cutting of plywood with the same thickness. And by attaching the model veneer that was used in shape cutting of the model and using it as a cutting guide, we can reduce the error of work and successively build the planned form. Since this study is about the need of a full scale model for a laminated wood model and an efficient process, this study concentrates more on process.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.5 s.133
• /
• pp.66-75
• /
• 2005

Soybean-based adhesives have recently been reconsidered as alternatives to petroleum-based adhesives due to the uncertainty of availability of petrochemical products and the increased demand for wood adhesives. This study was conducted to investigate the adhesive properties of alkaline phenolic soy (APS) resin for hybrid poplar flakeboard. The APS resin was formulated by crosslinking an alkaline soy flour hydrolyzate with lab-prepared PF resin in the soy hydrolyzate to PF resin weight ratios of 70/30, 60/40, and 50/50. The APS resins were used to fabricate homogeneous hybrid poplar flakeboards with different resin solid levels (5%, 7%, and 9%), press temperatures (175 and $200^{\circ}C$), and press times of 8 and 10 minutes. The IB, wet MOR, and dimensional stability properties of board improved with increasing press time, press temperature, and PF level in APS resins. Increasing press time can be used to offset poor IB strength associated with a 9% resin solid level and the excessive moisture content in the mat. The following conditions were concluded to meet the requirements of the CSA standard for exterior-grade flakeboard: a 50% PF level, a 5% resin content, a $200^{\circ}C$ press temperature, and an 8 minute press time.

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.6
• /
• pp.470-480
• /
• 2023

This study aimed to develop a sound-absorbing composite using sugarcane bagasse (SB) and coffee silver skin (CS) as raw materials. The composite boards were manufactured by bonding the fibers with Melamine Urea-Formaldehyde adhesive, ensuring a consistent thickness of 30 mm. Various densities were employed, namely 380, 450, and 520 kg/m³. The samples were fabricated with different fiber ratios, including SB100%, SB75% with CS25%, and SB50% with CS50%. The sound absorption coefficient (SAC) and noise reduction coefficient (NRC) were measured using the impedance tube method within a frequency range of 63-6,300 Hz. The experimental results revealed that the mixing ratio of CS exerted a notable influence on enhancing the SAC, while the density of the composite board exhibited a significant impact on increasing both the SAC and NRC. Among the densities tested, the optimal value was observed at 520 kg/m³, yielding a SAC value of 0.65 at a frequency of 1,000 Hz and an NRC value of 0.55 for the SB50-CS50 composite plate. These findings underscore the importance of considering the CS mixing ratio and composite board density when aiming to optimize sound absorption properties.

• Journal of the Korean Wood Science and Technology
• /
• v.52 no.4
• /
• pp.383-392
• /
• 2024

Laminated bamboo is an engineered bamboo technology to maintain its mechanical durability for both construction and furniture materials. This study was conducted to assess the properties of laminated bamboo made from Betung bamboo at different culm positions and laminate orientations. The materials used in this study were 4-year Betung bamboo (Dendrocalamus asper) obtained from a community forest in Yogyakarta and polyvinyl acetate resin as adhesive. Two factors were applied for this study, i.e., culm position (lower, middle, and upper) and laminate orientations (vertical and horizontal direction). To examine the mechanical properties, a static bending test and the hardness test were performed in accordance with ASTM D1037-99. Moisture content and density were determined in accordance with BS 373-1957. The results indicated that there was no interaction between the culm position and laminate orientation on the moisture content, density, static bending properties and hardness. The culm position affected the static bending and hardness, with the higher position of the culm resulting a greater strength. The laminate orientation also affected the strength of laminated bamboo, with the vertical direction resulting in higher strength than the horizontal.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.2
• /
• pp.61-68
• /
• 2007

The applicable scope of adhesives in the current society is broad and currently, several types of PVAc resin are sold in the market for adhesives. PVAc resin is primarily used for wood works and paper adhesion. However, the PVAc resin itself has the disadvantages that its viscosity is highly temperature- dependent and the work condition and viscosity get worse at the low temperature in the winter seasons. Although phthalate-based plasticizer is used to complement these disadvantages, adhesion strength and heat-resistance are weakened by adding the phthalate-based plasticizer and in the winter period, the amount of quantity should be increased. Also in a high-density product, it worsens the work condition by causing a rise of viscosity and delays curing and in a low-density product, it worsens the storage stability by causing separate precipitation. In addition to these, the phthalate-based plasticizer as a material of causing environmental hormones is currently restricted in the advanced countries for its amount of use and also in the domestic market, it is necessary to prepare for the situation. This study has not only eliminated the disadvantages of PVAc resin emulsion without adding a phthalate-based plasticizer of causing these problems, but also synthesized the PVAc resin for timber adhesion that is excellent in woodwork, thermal-resistance, water-resistance, storage stability, and adhesion performance. As the result, it has proven an excellent performance in thermal resistance, water resistance, storage stability, and minimum film forming temperature.

• Korean Journal of Heritage: History & Science
• /
• v.55 no.2
• /
• pp.200-211
• /
• 2022

The celadon stools with an openwork ring design which consist of four items as one collection were excavated from Gaeseong, Gyeonggi-do Province. The celadon stools were designated and managed as treasures due to their high arthistorical value in the form of demonstrating the excellence of celadon manufacturing techniques and the fanciful lifestyles during the Goryeo Dynasty. However, one of the items, which appeared to have been repaired and restored in the past, suffered a decline in aesthetic value due to the aging of the treatment materials and the lack of skill on the part of the conservator, raising the need for re-treatment as a result of structural instability. An examination of the conservation condition prior to conservation treatment found structural vulnerabilities because physical damage had been artificially inflicted throughout the area that was rendered defective at the time of manufacturing. The bonded surfaces for the cracked areas and detached fragments did not fit, and these areas and fragments had deteriorated because the adhesive trickled down onto the celadon surface or secondary contaminants, such as dust, were on the adhesive surface. The study identified the position, scope, and conditions of the bonded areas at the cracks UV rays and microscopy in order to investigate the condition of repair and restoration. By conducting Fourier-transform infrared spectroscopy(FT-IR) and portable x-ray fluorescence spectroscopy on the materials used for the former conservation treatment, the study confirmed the use of cellulose resins and epoxy resins as adhesives. Furthermore, the analysis revealed the addition of gypsum(CaSO₄·2H₂O) and bone meal(Ca₁₀ (PO₄)₆(OH)₂) to the adhesive to increase the bonding strength of some of the bonded areas that sustained force. Based on the results of the investigation, the conservation treatment for the artifact would focus on completely dismantling the existing bonded areas and then consolidating vulnerable areas through bonding and restoration. After removing and dismantling the prior adhesive used, the celadon stool was separated into 6 large fragments including the top and bottom, the curved legs, and some of the ring design. After dismantling, the remaining adhesive and contaminants were chemically and physically removed, and a steam cleaner was used to clean the fractured surfaces to increase the bonding efficacy of the re-bonding. The bonding of the artifact involved applying the adhesive differently depending on the bonding area and size. The cyanoacrylate resin Loctite 401 was used on the bonding area that held the positions of the fragments, while the acrylic resin Paraloid B-72 20%(in xylene) was treated on cross sections for reversibility in the areas that provided structural stability before bonding the fragments using the epoxy resin Epo-tek 301-2. For areas that would sustain force, as in the top and bottom, kaolin was added to Epo-tek 301-2 in order to reinforce the bonding strength. For the missing parts of the ring design where a continuous pattern could be assumed, a frame was made using SN-sheets, and the ring design was then modeled and restored by connecting the damaged cross section with Wood epos. Other restoration areas that occurred during bonding were treated by being filled with Wood epos for aesthetic and structural stabilization. Restored and filled areas were color-matched to avoid the feeling of disharmony from differences of texture in case of exhibitions in the future. The investigation and treatment process involving a variety of scientific technology was systematically documented so as to be utilized as basic data for the conservation and maintenance.