• 한국항공우주학회지
• /
• 제32권8호
• /
• pp.37-46
• /
• 2004

지면효과의 여러 현상을 Navier-Stokes 방정식을 이용하여 해석하고 공기역학적인 관점에서 그 결과를 분석하였다. 2차원 지면효과에 대해서는 이미지 와류에 의한 약형 표면의 압력변화, 두께의 영향, 지면효과의 비점성 유동 현상 등을 확인하였으며, 3차원 지면효과로 익단와류 강도의 증가현상과 유효스팬 증가, 익단와류의 바깥 흐름현상 등을 확인하였다. 또한, 재래식 익형인 NACA 6409와 러시아의 WIG기 전용익형인 DHMTU 8-30에 대해서 Irodov의 조건식을 사용하여 새로 정안정성을 해석하였다. 해석결과, DHMTU 8-30 익형의 세로 정안정성이 NACA 6409 익형보다 훨씬 우수한 것으로 나타났다. 그러므로 DHMTU 8-30을 WIG기에 사용할 경우 NACA 6409에 비해 꼬리날개 부피비를 현저히 줄일 수 있음을 확인하였다.

• 한국전산유체공학회지
• /
• 제18권3호
• /
• pp.8-13
• /
• 2013

Drag reduction of a running vehicle is very important issue for the energy savings and emission reduction of its power train. Especially for a solar powered electric vehicle, the drag reduction and weight lightening are two serious problems to be solved to extend its driving distance under the given energy condition. In this study, the ground effect of an airfoil shaped road vehicle was studied for an optimum body design of an ultra-light solar powered electric vehicle. Clark-Y airfoil type was adopted to the body shape of the model vehicle to reduce aerodynamic drag. From the study, it was found that the drag of the model vehicle was reduced as the height(h) between ground and the lower surface of the model vehicle was decreased. It is due to the reduction of the down-wash decreasing the induced drag of the vehicle. The lift was also decreased as the height decreased. It is due to the turbulent boundary layer developed beneath the vehicle body. The drag is classified into two types; the form and friction drag. The fraction of form drag to friction one is 76 to 24 on the model vehicle. As the height(h) of the model vehicle from the ground surface increases the form drag also increases but the friction drag is in reverse.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2005년도 춘계 학술대회논문집
• /
• pp.21-24
• /
• 2005

Numerical analysis were made for the unsteady flow fields of the rotor system of a Tilt-Rotor aircraft in cruise mode. The Reynolds-averaged thin-layer Wavier-Stokes equations were discretized by Roe's upwind differencing scheme and integrated in time by the LU-SGS algorithm. The computational domain of the rotor system was constructed by seven multi-block Chimera grids. Comparison of pressure coefficient on the surface of the main wing and blades were made for 3cases of advance ratio(0.325, 0.350, 0.375) and thrust and power coefficients for the rotor were compared with experimental data.

• Journal of Ship and Ocean Technology
• /
• 제12권4호
• /
• pp.20-31
• /
• 2008

Development of rudder gap flow blocking device for lift augmentation and cavitation suppression is presented. In order to verify the performance of this device, cavitation visualization and surface pressure measurements were carried out in a cavitation tunnel. Numerical simulations were conducted using a computational fluid dynamics code for more rigorous verification. The new rudder system is equipped with cam devices, which effectively close the gap between the horn/pintle and movable wing parts. The experimental and computational results show that the proposed rudder system is superior to the conventional rudder systems in terms of the lift augmentation and cavitation suppression.

• 한국정밀공학회지
• /
• 제28권8호
• /
• pp.975-983
• /
• 2011

A microfin on a heated surface and its effects of the heat transfer has been investigated. The thickness of the fin is about 8 micrometer to allow the flexible up-down motion of the fin. Two-way complete FSI (Fluid-Structure Interaction) method has been applied for the analysis. Firstly, the deformation of a microfin due to the pulsating flow is evaluated using structure analysis. The flow and temperature patterns are predicted by CFD (Computational Fluid Dynamics) method. At each time step, using the pressure force and temperature distribution from CFD, the deformation of the wing is evaluated by FEM. Also in order to estimate the resonance probability, the natural frequency of the wing structure is calculated by modal analysis. The proposed numerical procedure was validated through experiment using a single fin. Through this work, we show that the increase of 40% in heat transfer capacity using the microfin has been compared with that of flat plate case.

• 한국융합학회논문지
• /
• 제11권3호
• /
• pp.195-200
• /
• 2020

본 연구에서는 8개의 터빈 날개면들이 각각 추진축상에서 45°, 40°, 35°의 각도로 기울어져 있는 Model 1, 2 및 3인 3가지 Model의 유체클러치 터빈 날개 형상에 대한 유동 해석들을 수행하였다. 터빈 날개면이 추진축상에서 각도가 크게 기울어질수록 터빈 날개의 뒷면 이후에서의 흐름에서 Model들 중에서 가장 유동 압력을 크게 받고 있음을 알 수 있다. 반면에 터빈 날개면이 추진축상에서 각도가 작게 기울어질수록 유동 속도가 작게 된다. 터빈 날개면이 추진축상에서 각도가 작게 기울어질수록, 즉 유체의 흐름과 수직에 가까운 날개 형상이 효율적으로 유체클러치에 동력을 연결하고 차단하는데 있어서 적합함을 알 수 있다. 유체클러치 터빈 날개 유형별 유동해석을 적용함으로서 본 논문에서의 연구 결과는 미적인 설계를 적용할 수 있는 융합 연구자료로서 유리하다고 여겨진다.

• 대한기계학회논문집B
• /
• 제24권2호
• /
• pp.288-297
• /
• 2000

This paper describes the results of an experimental investigation of the flow characteristics and the heat transfer rate on a surface by interaction of a pair of vortices. The test facility consists of a boundary-layer wind tunnel with a vortex introduced into the flow by half-delta wings(vortex generators) protruding from the surface. In order to control the strength of the two longitudinal vortices, the angles of attack of the vortex generators are varied from 20 degree to 45 degree, but spacings between the vortex generators are fixed to 4 cm. The 3-dimensional mean velocity downstream of the vortex generators is measured by a five-hole pressure probe, and the hue-capturing method using the thermochromatic liquid crystals has been used to provide the local distribution of the heat transfer coefficient. By using the method mentioned above, the following conclusions are obtained from the present experiment. The boundary layer is thinned in the regions where the secondary flow is directed toward the wall and thickened where it is directed away from the wall. The peak augmentation of the local heat transfer coefficient occurs in the downwash region near the point of minimum boundary-layer thickness. Streamwise distributions of averaged Stanton number on the measurement planes show very similar trends for all the cases(${\beta}=20^{circ},\;30^{\circ}\;and\;45^{\circ}$).

• 대한기계학회논문집B
• /
• 제24권2호
• /
• pp.298-305
• /
• 2000

The flow characteristics and the heat transfer rate on a surface by interaction of a pair of vortices were studied experimentally. The test facility consisted of a boundary-layer wind tunnel with a vortex introduced into the flow by half-delta wings protruding from the surface. In order to control the strength of the longitudinal vortices, the angles of attack of the vortex generators were varied from - 20 degree to - 45 degree, but spacings between the vortex generators were fixed to 4 cm. The 3-dimensional mean velocity measurements were made using a five-hole pressure probe. Heat transfer measurements were made using the thermochromatic liquid to provide the local distribution of the heat transfer coefficient. Unlike common flow down, common flow up vortices moved toward the centerline as they developed and interacted strongly with each other but not with the boundary layer. Spanwise profiles of Stanton number were similar for ${\beta}=-20^{\circ}\;and\;-35^{\circ}$, but not similar for ${\beta}=-45^{\circ}$. The case of ${\beta}=-20^{\circ}\;and\;-35^{\circ}$ showed the two peak Stanton number, but the case of ${\beta}=-45^{\circ}$ showed the only one peak Stanton number.

• 대한기계학회논문집B
• /
• 제26권1호
• /
• pp.82-93
• /
• 2002

The effects of the interaction between the flow and temperature field and a boundary layer due to a variety of the height of a vortex generator are experimentally investigated. The test facility consists of a boundary-layer wind tunnel with the vortex generator protruding from the bottom surface. In order to control the strength of the longitudinal vortices, the angle of attack and the spacing distance of the vortex generator are 20 degree and 40 mm, respectively. The height of the vortex generator (H) is 15 mm, 20 mm and 30 mm and the cord length of it is 50 mm. Three-component mean velocity measurements are made using a 5-hole probe system and the surface temperature distribution is measured by the hue capturing method using thermochromatic liquid crystals. By using the method mentioned above, the following conclusions are obtained from the present experiment. The boundary layer is thinned in the downwash region where the strong downflow and the lateral outflow of the boundary layer fluid occur and thickened in the upwash re,3ion where the longitudinal vortex sweeps low momentum fluid away from the bottom surface. In case that the height of the vortex generator increases, the averaged circulation and the maximum vorticity of the vortex pair decrease. The contours of the non-dimensional temperature show the similar trends fur all the cases (H=15 mm, 20 mm and 30 mm). The peak augmentation of the distribution of the local non-dimensional temperature occurs in the downwash region near the point of minimum boundary-layer thickness.

• 대한조선학회논문집
• /
• 제37권3호
• /
• pp.57-68
• /
• 2000

이착륙 속력을 줄이기 위해 날개 밑으로 프로펠러 후류를 불어넣어 날개와 수면사이의 압력을 증가시키는 PAR(Power Augmented Ram) 효과는 해면효과익선의 성능을 크게 향상시킨다. 본 논문에서는 풍동실험을 통해 이러한 PARWIG(Wing in Ground)선의 공력특성을 연구하였으며 송풍기(blower)와 덕트(duct)를 사용한 제트분사를 프로펠러 후류로 대신하였다. 제트의 분사속도, 분사위치(수평 및 수직 방향), 분사각 및 덕트 직경 변화에 대해 20인승 PARWIG선의 1/25 축소 모형선의 지면과의 고도, 앙각 및 플랩각의 변화에 따른 양력, 항력 및 피치모멘트를 계측하여 공력특성을 비교하였다. 적절한 PAR효과의 사용은 양력을 크게 증가시키며 최대 4의 양력계수까지 얻을 수 있었다.