• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.1
• /
• pp.64-71
• /
• 2010

This paper deals with an economic evaluation of domestic immersing type photoelectrochemical hydrogen production. We also make some sensitivity analysis of hydrogen production prices by changing the values of input factors such as the initial capital cost, the solar to hydrogen conversion efficiency, and the system duration time. The hydrogen production price of the immersing type photoelectrochemical system was estimated as 8,264,324 won/$kgH_2$. It is expected that the production cost by photoelectrochemical hydrogen production can be reduced to 26,961 won/$kgH_2$ if the solar to hydrogen conversion efficiency is increased to 14%, the system duration time is increased to 20,000 hours, and the initial capital cost is decreased to 10% of the current level. The photoelectrochemical hydrogen production is evaluated as uneconomical at this time, and we need to enhance the solar to hydrogen conversion efficiency and the system duration time as well as to reduce prices of the system facilities.

• Steel and Composite Structures
• /
• v.23 no.2
• /
• pp.161-172
• /
• 2017

A new composite tube connection method called the pre-tightened teeth connection technique is proposed to improve the composite tube connection efficiency. This paper first introduces the manufacturing process of the proposed technique. It then outlines how the mechanical properties of this technology were tested using four test groups. The factors that influence the load-bearing capacity and damage model of the connection were analyzed, and finally, the transfer load mechanism was investigated. The following conclusions can be obtained from the research results. (1) The new technique improves the compressive connection efficiency by a maximum of 79%, with the efficiency exceeding that of adhesive connections of the same thickness. (2) Changing the depth of teeth results in two types of damage: local compressive damage and shear damage. The bearing capacity can be improved by increasing the depth, length, and number of teeth as well as the pre-tightening force. (3) The capacity of the technique to transfer high loads is a result of both the relatively high interlaminar shear strength of the pultruded composite and the interlaminar shear strength increase provided by the pre-tightening force. The proposed technique shows favorable mechanical properties, and therefore, it can be extensively applied in the engineering field.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11b
• /
• pp.378-387
• /
• 2000

A rice mill plant with a capacity of 2.5 ton/hr was constructed with automated facilities at Chonnam National University. A simulation model was developed with SLAM SYSTEM for evaluating and improving the rice mill plant. The developed model was validated in the views of hulling efficiency, milling efficiency, milled rice recovery, other materials produced, and bottlenecks in the processes. The results of hulling efficiency, milling efficiency, milled rice recovery in the simulation were, respectively, 81.1%, 89.5%, and 73.1%, while those of the actual mill plant were 81.5%, 90.2%, and 73.5%. The simulation results including the productivity of other materials(chaff, bran, broken rice, stone, etc) produced in the processes were almost similar with those of the actual process. In the simulation the bottlenecks were found out in the processes of separating brown rice and of sorting colored rice. These phenomenon also appeared in the actual process. It needed to increase the hourly capacity of the brown rice separator and the rice color sorter. As the developed model could well express the automated rice mill plant, it could be used for designing and improving rice mill plants. In addition, an alternative model needed to be developed for the system control more accurately and for increasing the rice quality.

• Journal of Life Science
• /
• v.9 no.5
• /
• pp.575-580
• /
• 1999

Even if odorous compounds remained very low concentration in water, it caused strong odor. Because Geosmin and most of odorous compound had very vaporization, those were difficult to analyze with GC/MSD and Purge & Trap. So, we needed pre-treatment method for decreasing amounts of extracting solvents, improving recovery efficiencies and increasing analytical efficiencies. This study developed efficient technology for analyzing odorous compounds, using various adsorbents and extracting solvents. The optimum adsorbent was XAD resins. Especially, XAD-2, XAD-7 and XAD-2010 were superior, but XAD-2 of these and MTBE was the optimum extraction solvent. Other extraction solvent's efficiency was in order of MTBE>Dichloromethane>n-Hexane>Diethylether. The optimum NaCl dosage for increasing efficiency was 5g in liquid-liquid extraction method. The shaking time(0∼24hr) had no concern with adsorption efficiency. The optimum adsorbent was XAD-2 resin and extraction solvent was MTBE. Dosing NaCl, adsorption efficiency was increased in liquid-liquid extraction method, but NaCl has no effect on liquid-solid extraction method. In this experimental results, this method will apply to not only Geosmin but other well-known odorous compounds (2-MIB, IBMP, IPMP, TCA) and algae toxins (Mycrocystin, Anatoxin etc)

• Journal of Biomedical Engineering Research
• /
• v.22 no.2
• /
• pp.205-210
• /
• 2001

The effectiveness of extracorporeal shock wave lithotripter for the therapy of calculus has been well known in the field of urology. There are many studies about the performance of that and the influence into human body. Among them, it is an impertant issue that cavitation is always deal with shock wave. A medium of the shock wave is related to the cavitation phenomenon. In this paper, therefore, we analysis the spectra of radiated sounds and the break efficiency on focal region due to the medium of shock wave. The results show that the cavitation bubbles produce a harmful on the break efficiency and the stability of the radiated sounds due to the ESWL.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.293-298
• /
• 2011

The most widely used method to form an electrode in industrial solar cells are screen printing. Screen printing is characterized by a relatively simple and well-known production sequence with high throughput rates. However the method is difficult to implement a fine line width of high-efficiency solar cells can not be made. The open circuit voltage(Voc) and the short circuit current density(Jsc) and fill factor(FF) need to be further improved to increase the efficiency of silicon solar cells. In this study, gravure offset printing method using the multicrystalline-silicon solar cells were fabricated. Gravure off-set printing method which can print the fine line width of finger electrode can have the ability reduce the shaded area and increase the Jsc. Moreover it can make a high aspect ratio thereby series resistance is reduced and FF is increased. Approximately $50{\mu}m$ line width with $35{\mu}m$ height was achieved. The efficiency of gravure off set was 0.7% higher compare to that of scree printing method.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.6
• /
• pp.535-542
• /
• 2008

This paper presents a high efficiency half-bridge DC-DC converter for an LED backlight drive system of LCD module inspection equipment. The proposed converter improves the converter efficiency using characteristics of the asymmetrical half-bridge converter and the self-driven synchronous rectifier, and thus improves the total efficiency of the LED backlight drive system. The synchronous rectifier applied to the proposed converter is the new topological synchronous rectifier, which changes slightly the transformer structure and the synchronous switch connection in the asymmetrical half-bridge converter with a conventional self-driven synchronous rectifier. Since the proposed converter utilizes the transformer leakage inductor as its resonant inductor, its structure is simplified. The proposed converter well operates under the universal DC input voltage ($250{\sim}380V$). The operational principle and a design example for a 100W prototype are discussed in detail, respectively. Experimental results are shown for the designed prototype converter under universal DC input voltage.

• IE interfaces
• /
• v.16 no.spc
• /
• pp.76-81
• /
• 2003

BPMS (Business Process Management Systems) is aninformation system that systematically supports designing, administrating, and improving the business processes. It can execute the business processes by assigning tasks to human or computer agents according to the predefined definitions of the processes. In this research we developed a task assignment algorithm that can maximize overall process efficiency under the limitation of agents' capacity. Since BPMS manipulates the formal and predictable business processes, we can analyze the processes using queuing theory to achieve overall process efficiency. We first transform the business processes into queuing network model in which the agents are considered as servers. After that, workloads of agents are calculated as server utilization and we can determine the task assignment policy by balancing the workloads. This will make the workloads of all agents be minimized, and the overall process efficiency is achieved in this way. Another application of the results can be capacity planning of agents in advance and business process optimization in reengineering context. We performed the simulation analysis to validate the results and also show the effectiveness of the algorithm by comparing with well known dispatching policies.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.5
• /
• pp.412-419
• /
• 2020

In this study, a 70 W buck converter using GaN metal-oxide-semiconductor field-effect transistor (MOSFET) is developed. This converter exhibits over 97 % efficiency, high power density, and 48 V-to-12 V/1.2 V/1 V (triple output). Three gate drivers and six GaN MOSFETs are placed in a 1 ㎠ area to enhance power density and heat dissipation capacity. The theoretical switching and conduction losses of the GaN MOSFETs are calculated. Inductances, capacitances, and resistances for the output filters of the three buck converters are determined to achieve the desired current, voltage ripples, and efficiency. An equivalent circuit model for the thermal analysis of the proposed triple-output buck converter is presented. The junction temperatures of the GaN MOSFETs are estimated using the thermal model. Circuit operation and temperature analysis are evaluated using a circuit simulation tool and the finite element analysis results. An experimental test bed is built to evaluate the proposed design. The estimated switch and heat sink temperatures coincide well with the measured results. The designed buck converter has 130 W/in³ power density and 97.6 % efficiency.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.12
• /
• pp.594-599
• /
• 2014

There have been many cases that the air curtain installed in the apartment can not well remove the gases such as carbon dioxide and particles such as smokes, oils and vapors generated during the cooking to disperse the pollutants into the room. This study uses the numerical analysis to show how the pollutant-removing performance of the range hood is changed when the air curtain is installed on the range hood of kitchen. As a result of the study, it turned out that, when the air amount supplied by air curtain through the slot was about 60% of exhaust amount, the capturing efficiency of range hood for pollutants increased by 70~80% more than the case without the air curtain. Even when the exhaust amount was small, the capturing efficiency was improved a lot with the use of air curtain. In case that the air flow velocity of slot was greater than 2 m/s, the capturing efficiency turned out to decrease.