• Journal of Welding and Joining
• /
• v.35 no.1
• /
• pp.68-73
• /
• 2017

During welding of Ni based superalloy, hot cracking was usually happen in the fusion zone of a weld. In this study, the laser weldability of Inconel 713C alloy for the turbocharger wastegate valve (WGV) was evaluated with various welding conditions, such as laser power, welding speed, shielding gas. Welding conditions were optimized by bead-on-plate (BOP) and butt joint welding. For the evaluation of laser weldability, bead shapes and weld microstructures were investigated and tensile test was conducted. The fracture surfaces were investigated for the understanding the cause of the fracture.

• Journal of Welding and Joining
• /
• v.18 no.1
• /
• pp.52-58
• /
• 2000

Spot welding, namely a kind of electric resisting welding has been used widely in field of automobile and aircraft industries because of easiness to apply. Specimens used in this study was a mild steel of 1.2mm thickness and the electrode was a Cu-Cr alloy of 6mm diameter. The surface sheared of specimens after testing of tensile shear was observed by SEM(scanning electron microscope) after ultrasonic cleaning for 10min., and microstructures and grain size of all specimens were measured with using of O.M.(Optical microscope). By the means of measurement and observations of tensile shear load, fatigue strength and share surface, the weldability of spot welding was evaluated. When tensile shearing testing, fracture starting point in all specimens was took place at the bond between HAZ(Heat affected zone) and nugget. With increasing in number of layers, fatigue strength was decreased. With increasing in electric current, grain size in the HAZ became more fine.

• Journal of Welding and Joining
• /
• v.22 no.5
• /
• pp.58-64
• /
• 2004

Although leakage at a low carbon steel pipe made by electrical resistance welding (ERW) was reported due to grooving corrosion, the cause for the corrosion has not yet been cleared. In order to clarify the main cause, failure analysis on the leaked pipe was carried out, followed by metallographic investigation and corrosion test for the various ERW pipe made with different welding heat input. The microstructure, particularly inclusion content, of the weldment is dependant on the welding heat input applied. For an improper low heat input, the amount of inclusion at the weld was high. High inclusion content accelerated grooving corrosion at the weld. It is therefore that welding heat input should be controlled based on the carbon content of the pipe in order to improve the corrosion resistance of the ERW pipe.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.4
• /
• pp.517-522
• /
• 2011

Conventional projection welding systems suffer from lots of defective products caused by manual handling. In this paper, we introduce a projection welding system that performs automatic identification, welding and counting of components and products. The proposed system checks the existence and identifies placement of components to be welded by a vision camera. After welding of the components, it automatically updates product counts and dressing items. We show that the proposed welding system can reduce the defect rate and improve the productivity through experimental test with a existing system.

• Korean Journal of Computational Design and Engineering
• /
• v.21 no.2
• /
• pp.143-150
• /
• 2016

In shipbuilding, hull assemblies are manufactured by welding. The thermal deformation caused by the welding produces shape deformation. Counter-deformed design methods have been used in shipyards to cope with the weld-induced deformation of ship assembles. Finite element methods (FEMs) are frequently used to estimate welding distortion in the counter-deformed design. For the estimation of welding distortion, producing uniform rectangular elements is required to enter thermal loads on the welding line and obtain accurate analysis results. In this paper, a new automatic mesh generation method is proposed for prediction of welding deformation in FEM. Meshes are constructed for test cases to demonstrate the feasibility of the proposed mesh generation method.

• Journal of Welding and Joining
• /
• v.10 no.2
• /
• pp.32-42
• /
• 1992

A method of optimization of process parameters in Arc Welding has been discussed in this paper. The method of investigation is based on the numerical calculation of weld bead by a finite element method and non-linear optimization technique is applied to estimated the optimization process parameters from the numerical calculation. The common package program(ANSYS 4.4A) was used to obtain the process parameters for a thin plate arc welding (TIG, CO$_{2}$). The results on some test are satisfactory and the used method of this paper is a useful guide to the optimum welding condition.

• Journal of Welding and Joining
• /
• v.29 no.2
• /
• pp.94-101
• /
• 2011

A lumped mass damped vibratory model was proposed for quantitative understanding of welding machine characteristics. An experimental setup was developed to determine the mechanical parameters (moving mass m, equivalent stiffness k and damping c) which govern the dynamic mechanical response of the resistance spot welding machine. During the test, acceleration of the electrodes for each level of applied load was measured by accelerometer, filtered and numerically integrated to find the corresponding velocity and displacement. The machine dynamic parameters were determined by finding the unknowns of the proposed model with experimental data. A Simulink model was proposed to investigate the influence of these mechanical parameters on the welding process. The electrode response was simulated by changing values of stiffness and damping. It was observed that both of the machine parameters(c, k) have significant effect on the response of electrode head.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.10
• /
• pp.571-578
• /
• 1999

Current waveform control of pulse MAG welding power source is studied so that welding of thin plates may obtain high speed and improved performance. In this paper, waveform control method is proposed, digital controller using DSP is able to control the current waveform precisely. High speed welding of thin plates using pulse MAG welding method is made possible. Performance test for 1.2mm thin plates is carried out, output waveform and welding performance is analyzed.

• Journal of Welding and Joining
• /
• v.25 no.4
• /
• pp.65-71
• /
• 2007

Laser weldability of the aluminized steel for the full penetration welding will be described in this paper. We focused on the effect of Al coating conditions on weld strength. For these objectives, aluminized steel sheets that have various thickness and coating weight were prepared for laser welding. And then, tensile-shear and hardness test were carried out. At the same time, Al contents in weld after laser welding were analyzed and their correlations with mechanical properties were investigated. Besides, as removing partially coating layer, weldability has been investigated according to the position of coating layer. As a result of this study, tensile-shear strength was decreased with increasing Al contents in weld, and Al of coating layer caused grain growth.

• International Journal of Korean Welding Society
• /
• v.4 no.1
• /
• pp.10-14
• /
• 2004

In this paper, a study on the residual stress of plate with longitudinal stiffeners is explained in terms of the welding sequences. In order to verify the results of numerical analysis, the hole drilling method (HDM) is performed, to measuring the residual stresses of the test plates in $CO_2$ Flux Cored Arc Welding (FCAW) under various welding conditions. The non-linear transient analysis technique for the numerical analysis in a large and complicate structure is considered. The residual stress of plate in consideration of the welding sequences and directions is evaluated by some numerical simulations and also by experiments. Comparison of numerical analysis results with experimental data shows the accuracy and validity of the proposed method.