• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.9 no.1
• /
• pp.100-111
• /
• 2006

This study was carried out to increase the efficiency of site investigation through the evaluation of the applicable methods of investigation for cutting slope design. In an effort to find out the applicability of the method employed during the slope investigation, some tests were carried out on 6 subjects i.e location of weak zones, characteristics of discontinuities, distribution of strata, in situ tests for geo-technical properties, laboratory test and estimation of weathering. The method was highly applicable and produced expected results during the test of weak zones, discontinuities and distribution of strata. In order to apply the method to in- situ test for geo-technical properties and laboratory test on soil and rock slope, a statistic analysis of the existing data were required in advance. However its design applicability on rock slope was good although actual cases of application were not many due to limitation of the cases for investigation. The method was frequently referenced but not actually applied for anti seismic design test and estimation of weathering.

• Journal of the Korea Construction Safety Engineering Association
• /
• s.45
• /
• pp.60-70
• /
• 2008

Mechanized tunnelling by TBMs has been extensively adopted for last two decades. Nevertheless, only few case histories have been reported. Unlike NATM tunnels, the case histories of the weak zone have been seldom reported for the mechanized tunnelling, even in the other countries. In this study, a collapse of TBM tunnel occurred in the severely altered weak rock zones between volcaniclastic rocks and granitic rocks was briefly described. A systematic geotechnical investigation, which was performed to examine the cause of the collapse, was carried out at the site and then characteristics of the rocks in the zones were evaluated. Moreover, This study propose a guide line of estimateing the possibility of collapse in TBM tunnels through comparing experimental results with surveying results of general rocks.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1998.10a
• /
• pp.121-128
• /
• 1998

• Journal of the Korean GEO-environmental Society
• /
• v.23 no.3
• /
• pp.5-13
• /
• 2022

In this study a test was conducted to identify weak section using 100kJ class rock energy to find out the protection performance of rockfall prevention fences in Korea. Performance rating of the rockfall protection fences is very low (48~61kJ) compared to that of foreign countries and it is necessary to determine whether it can function properly if high rock energy is generated. Furthermore, a reinforcing technology that can improve to 100kJ energy on the existing rockfall protection fences should be developed. Therefore, this study confirmed the protection performance using 100kJ rock energy in the existing rockfall protection fence system (for national road, for highway) and identified weak section of post, wire ropes and nets. Furthermore, it will be used as basic data for developing 100kJ class reinforcement technology without dismantling the existing rockfall protection fence (48-61kJ).

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.10a
• /
• pp.285-289
• /
• 2005

The Cenozoic Era consists of two period , the Tertiary and the Quaternary Period. Weak rock types may include areas containing: 1) poorly cemented or uncemented sediments, 2) highly weathered rock, or 3) fault lines. Especially this paper deal with poorly cemented or uncemented sedimentary rocks in slope. Mechanical weathering is caused by physical processes such as absorption and release of water, and changes in temperature and stress at or near the exposed rock surface. It results in the opening of discontinuities, the formation of new discontinuities by rock fracture, the opening of grain boundaries, and the fracture or cleavage of individual mineral grains. Decomposition causes some silicate minerals such as feldspars to change to clay minerals. There was a strong negative correlation between water absorption and important engineering properties such as strength and durability.

• Tunnel and Underground Space
• /
• v.4 no.3
• /
• pp.297-304
• /
• 1994

This study aimed at analysis of induced stress and deformation behavior in rock mass around coal seams of Sam Chuck coal mine. For this study Vibrating Wire Stressmeters and Multi-point Borehole Extensometers were installed in the area of coal shale near coal seams. Induced stress and displacement in this area were coutinuously increased for 6 days from the begining of measurement, and then converged. But induced stress and displacement occurred when there were another openings by tunnelling and mining. The value of final induced stress was 21.8kgf/$\textrm{cm}^2$, displacement of rod extensometer was 1.3 mm at arch. Especially, over 1 mm of displacement between E2 and E3 in rod extensometer was measured.

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2000.09a
• /
• pp.183-193
• /
• 2000

A series of studies such as geological logging data analysis, detailed geological survey, rock mass evaluation, in-situ and laboratory tests, rock strength and mechanical properties of the rock were concerned. The stability of the slope were carried out inorder to design the pit slope and individual benches using the stereographic projection analysis and numerical methods in Roto Pit of Pasir coal fetid. The bedding plane was one of the major discontinuities in the Roto Pit and the dip of which is about $60^{\circ}$in the northern part and $83^{\circ}$in the southern part. The dip of bedding becomes steeper from north to south. The plane and toppling failures are presented in many slopes. In laboratory test the average uniaxial compressive strength of mudstone was 9 MPa and that of weak sandstone was 10 MPa. In-situ test showed that the rocks of Roto north mining area are mostly weak enough to be classified in grade from R2(weak) to R3(medium strong weak) and the coal is classified in grades from R1(Very weak) to R2(Weak). The detailed stability analysis were carried out on 4 areas of Roto north(east, west, south and north), and 2 areas of Roto south(east and west). In this paper, the minimum factor of safety was set to 1.2 which is a general criterion for open pit mines. Using the stereographic projection analysis and the limit equilibrium method, slope angles were calculated as 30~$36^{\circ}$for a factor of safety greater than 1.2. Then these results were re-evaluated by numerical analysis using FLAC. The final slope angles were determined by rational described abode. A final slope of 34 degrees can guarantee the stability for the eastern part of the Roto north area, 33 degrees for the western part, 35 degrees for the northern part and 35 degrees for the southern part. For the Roto south area, 36 degrees was suggested for both sides of the pit. Once the pit slope is designed based on the stability analysis and the safety measures. the stability of 니ope should be checked periodically during the mining operations. Because the slope face will be exposed long time to the rain fall, a study such aspreventive measures against weathering and erosion is highly recommended to be implemented.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.5
• /
• pp.657-673
• /
• 2019

A monitoring method based on acoustic emission (AE) sensor has been widely used to evaluate the damage of structures in underground rock. The acoustic emission signal generated from cracking in material is analyzed as various acoustic emission parameters in time and frequency domain. To investigate from initial crack generation to final failure of rock material, it is important to understand the characteristics of acoustic emission parameters according to the stress ratio and rock strength. In this study, uniaxial compression tests were performed using very strong and weak rock specimen in order to investigate the acoustic emission parameters when the failure of specimen occurred. In the results of experimental tests, the event, root-mean-square (RMS) voltage, amplitude, and absolute energy of very strong rock specimen were larger than those of the weak rock specimen with an increase of stress ratio. In addition, the acoustic emission parameters related in frequency were more affected by specification (e.g., operation and resonant frequency) of sensors than the stress ratio or rock strength. It is expected that this study may be meaningful for evaluating the damage of underground rock when the health monitoring based on the acoustic emission technique will be performed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.652-661
• /
• 2006

The cut slopes in Jinju area constitute the Cretaceous Sedimentary rock which is one of the most poor ground conditions. The geological rocks of the cut slopes are correlated with Jinju Formation. Most of the rocks consist of Black Shale layer, but the lower parts consist of Alkorsic White Sandstone. So, It is characteristic of the differential weathering due to the difference of rock species. Moreover, vertical joints which concentrate on the released rock and weak rock fragments are accompanied with minor faults. We make out face mapping about each slopes through the detailed field-study and deduce RMR and SMR from the field data. The strength properties of rocks were obtained from references, indoor tests, and Back Analysis method. And, choosing properties were used in the stability analysis as stereographic projection and limit equilibrium analysis and we establish the countermeasures for the cut slopes.

• Tunnel and Underground Space
• /
• v.15 no.3 s.56
• /
• pp.195-212
• /
• 2005

Surface subsidence which occurs with several reasons, such as collapse of gangway, discharge of groundwater, compaction of weak rock mass, and tunnel excavation in shallow depth, gives rise to a serious problem in national infra-structures. In this study, therefore, the mechanism of subsidence has been examined numerically to overcome the passive approach on subsidence occurrence area. With many kinds of numerical studies, the major geotechnical parameters have been selected and the weighted values have been defined for each parameters. Also the authors developed the numerical program which can estimate the possibility of subsidence occurrence, and proposed the decision method for objective and quantitative guideline. It is anticipated that this research will be helpful to establish the hazard map on subsidence region.