• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.515-518
• /
• 2005

In this paper, we report on our theoretical study on the effect of surface anchoring. Molecular dynamics as well as optical characteristics of PVA cell are computer-simulated with 3D-FEM numerical solver, TechWiz $LCD^{(R)}$. Although simulation parameters are the same except for the consideration of surface anchoring, the simulation reveals that optical transmittance is improved by more than 8% for the weak anchoring case with comparison to the strong anchoring case. Moreover, capacitance between pixel and common electrode is 7% lower for the strong anchoring than that for the weak anchoring. This implies that there exists an appreciable difference between the strong anchoring case and the weak anchoring case. It is very important to take the effect of surface anchoring into account in order to figure out the optical characteristics of an LCD cell more accurately.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.11
• /
• pp.969-976
• /
• 2007

In this thesis, an anchoring energy in the upper and lower substrates of TFT-LCD cell has been modeled and applied in the numerical calculation of the molecular orientation of the TN-LCD. The molecular orientation of liquid crystals defined as tilt and twist angles was simulated using the Newton-Raphson method and the Gaussian integration method. From the results, the tilt and twist angles for the strong anchoring energy were proven to be coincide with those of the conventional results. on the other hand, for the weak anchoring energy, azimuth angles of the molecules were changed abruptly from $0^{\circ}\;to\;90^{\circ}$ near the middle area of the cell due to the balance of the anchoring energy and the elastic energy of the liquid crystals.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.12 no.1
• /
• pp.69-74
• /
• 1999

We have investigated that the high pretilt angle of the NLC, 4-n-pentyl-4-cyanobiphenyl (5CB), was observed on rubbed polythiophene (PTP) surfaces with alkyl chains with more than 10 carbon atoms; it is attributed to the surface-excluded volume effect by the alkyl chain lengths between the LCs and the PTP surfaces. Next, we investigated that the odd-even effect of the polar anchoring strength in 5CB on rubbed PTP surfaces with alkyl chain lengths has been successfully evaluated. The anchoring strength of 5CB for rubbed PTP surfaces with odd-number is weak compared with even-number up to the 6 carbon atoms in the alkyl chain; however, odd-number is strong compared with even-number above 7 carbon atoms. The weak anchoring strength of 5CB is approximately $1\times10^{-3} (J/m^2$) on rubbed PTP surface with 7 carbon atoms; it is relatively strong anchoring strength. Consequently, we conclude that the odd-even effects of the polar anchoring strength in NLCs are strongly related to the characteristics of the polymer and observed clearly for short alkyl chain lengths.

• Journal of Information Display
• /
• v.6 no.3
• /
• pp.1-5
• /
• 2005

The recent Bistable Nematic ($BiNem^{(R)}$) LCD technology presents long term bistability, high level passive matrix multiplexing, gray levels capabilities and high optical quality. The $BiNem^{(R)}$ device, based on anchoring breaking, needs specific low anchoring strength materials - alignment layers and liquid crystal mixtures. We present here our approach to develop nematic mixtures with wide enough temperature range and low zenithal anchoring energy.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.12
• /
• pp.1128-1132
• /
• 1998

We have investigated the relationship between the polar anchoring energy and the surface order parameter in nematic liquid crystal (NLC), 4-n-pentyl-4-cyanobiphenyl (5CB), on the two kinds of the weakly rubbed polyimide (PI) surfaces. The observed polar anchoring energy of 5CB is approximately 2${\times}10^{-4}(J/m^2$) and then increases with increasing the rubbing strength (RS) on weakly rubbed surface (RS=57mm) with side chain at $30^{\circ}C$; same results are obtained on weakly rubbed PI surface without side chain. The surface order parameter of 5CB on rubbed PI surfaces increases with increasing the RS at a weak rubbing region. The surface order parameter of 5CB is strongly related to the characteristics of PI material. Consequently, we suggest that the polar anchoring energy of NLC is strongly attributed to the surface order parameter on rubbed PI surfaces.

• 한국연소학회:학술대회논문집
• /
• 2014.11a
• /
• pp.357-358
• /
• 2014

Coherent anti-Stokes Raman spectroscopy is one of the best tools to measure temperature distributions in the flame. Since it does not disturb the flow field, it could be used to study anchoring mechanism especially in the lifted flame. However, the length of probe volume is, normally, much greater than flame thickness. This weak point was overcome with lens combination in this study. It was found out that no peculiar temperature changes was happened near tribrachial point and heat transfer to the upstream was minimal near the flame anchoring position.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.619-621
• /
• 2003

We have presented in the paper preliminary results on physical characteristic parameters of a photopolymer LPPF 301 CP. The weak azimuthal anchoring energy (${\sim}5.0{\times}10^{-6}J/m^2$) of a photopolymer was measured by using a simple optical method. High pretilt up to $30^{\circ}$ has been achieved in the photoaligned cell by irradiating an obliquely incident UV light.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.87-90
• /
• 2009

A dual-cell-gap transflective liquid crystal display (TR-LCD) with identical response time in the transmissive and reflective regions is demonstrated. In the transmissive region, strong anchoring energy condition is used to decrease the response time, while in the reflective region weak anchoring energy condition is used to increase the response time. The simulated dual-cell-gap TR-LCD has good performances.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.539-542
• /
• 2003

We have studied cell gap-dependent electrode-optic characteristics of the FFS mode using the LC with negative dielectric anisotropy. In case of a small cell gap of 2 ${\mu}m$, the transmittance at the center of pixel and common electrodes is low due to stronger influence of surface anchoring that holds the LC to the initial state than twisting force induced by neighboring LCs. In case of a large cell gap of 4 ${\mu}m$, the influence of surface anchoring force becomes weak so that the LCs at the center of pixel and common electrode can be twisted enough by applied voltage, giving rise to high transmittance. Therefore, we conclude that the light efficiency in the device is dependent on the cell gap.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1600-1602
• /
• 1996

We have investigated the anisotropic dispersion force effects for surfaces alignment of liquid crystals (LCs) on rubbed polystyrene (PS) surfaces by unidirection. In microphotographs an of the textures, we obtained the nematic (N) LCs are shown to align in both direction parallel and perpendicular to the rubbing for region up to medium rubbing, however to align in the direction perpendicular to the rubbing for strong rubbing region. We suggest that the anisotropic dispersion force is very important rather than macro-surface groove effect to uniform alignment of LCs. We also measured the temperature dependence of extrapolation length of 5CB on rubbed PS surfaces for strong rubbing. It is shown that the polar anchoring strength of 5CB is very weak on rubbed PS surface compared to the rubbed polyimide (PI) surface.