• 소성∙가공
• /
• 제21권1호
• /
• pp.58-66
• /
• 2012

The work roll surface temperature rises and falls repetitively during hot slab rolling because the work roll surface is cooled continuously by water. This study focused on Std. No. 7 to determine a cooling method which significantly reduces the tangential tensile stresses on the work roll surface of the hot slab mill at Hyundai Steel Co. in Korea. A series of finite element analyses were performed to compute the temperature distribution and the tensile stresses in the circumferential direction of the work roll. The virtual slab model was used to reduce the run time considerably by assigning a high temperature to the virtual slab. Except for the heat generated by plastic deformation, this is equivalent to the hot rolling condition that a high temperature slab (material) would experience when in contact with the work rolls. Results showed that when the virtual slab model was coupled with FE analysis, the run time was found to be reduced from 2000 hours to 70 hours. When the work roll surface cooled with a certain on-off patter of water spray, the magnitude of the tangential stresses on the work rolls were decreased by 54.1%, in comparison with those cooled by continuous water spraying. Savings of up to 83.3% in water usage are possible if the proposed water cooling method is adopted.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권7호
• /
• pp.907-913
• /
• 2011

Swirling flows are related to the spiral motion in the tangential direction in addition to the axial and radial direction using several swirl generators. These type of flows are used in combustion chambers to improve flame stability, heat exchanger to enhance heat transfer coefficients, agricultural spraying machines and some vertical pipes to move slurries or transport of materials. However, only a few studies three dimensional velocity profiles in a vertical pipe have been reported. In this present paper, 3 dimension particle image velocimetry(PIV) technique was employed to measure the velocity profiles in water along a vertical circular pipe with Reynolds number from 6000 to 13,000. A tangential inlet condition was used as the swirl generator to produce the required flow. The velocities were measured with swirling flow in the water along the test section using the PIV technique.

• Journal of Mechanical Science and Technology
• /
• 제18권4호
• /
• pp.699-708
• /
• 2004

Natural gas hydrate typically contains 85 wt.% water and 15 wt.% natural gas, and commonly belongs to cubic structure I and II. When referred to standard conditions, 1 ㎤ solid hydrate contains up to 200㎥ of natural gas depending on pressure and temperature. Such the large volume of natural gas hydrate can be utilized to store and transport a large quantity of natural gas in a stable condition. In the present investigation, experiments were carried out for the formation of natural gas hydrate governed by pressure, temperature, gas compositions, etc. The results show that the equilibrium pressure of structure II is approximately 65% lower and the solubility is approximately 3 times higher than structure I. It is also found that for the sub-cooling of structure I and II of more than 9 and 11 K respectively, the hydrates are rapidly being formed. It is noted that utilizing nozzles for spraying water in the form of droplets into the natural gas dramatically reduces the hydrate formation time and increases its solubility at the same time.

• 한국표면공학회지
• /
• 제27권3호
• /
• pp.149-157
• /
• 1994

The formation of spangles on a hot dip galvanized sheet steel by spray cooling the molten zinc coating with air, water and 2.0wt% $NH_4H_2PO_4$ solution has been studied performing laboratory experiments, and their coating properties have been evaluated. Minimized spangles were easily formed by mist spraying the solution for 1 second at the low nozzle spray pressure onto the molten zinc at 420~$422^{\circ}C$ because the solute $NH_4H_2PO_4$ in the sprayed solution imparted a highly rapid cooling effect to the coating through its endothermic de-composition reactions and because the decomposed products acted as numerous nucleation sites for the mini-mized spangles on the coating. Good surface appearances sand sound coating properties were obtained on this coating. Only regular spangles were formed on the coating by the forced convective air cooling. At the high nozzle spray pressure, zero spangles were formed on the coating by the pure water spray cooling. However, the coating had a dull and rough surface with craters sand cracks.

• 설비공학논문집
• /
• 제14권8호
• /
• pp.671-675
• /
• 2002

The gas adsorption efficiency for various surfaces with three different characteristics has been reviewed. The dimethyl disulfide gas has been used to investigate characteristics of gas adsorption for different surface characteristics such as plasma treated, lacquer coated and untreated. Three different surfaces were evaluated in dry conditions initially and tested at wet surface conditions with spraying water to evaluate the gas adsorption efficiency which usually occurred at defrost cycles. The results show that the gas adsorption of the plasma treated sample has better performance than others. The lacquer coated and untreated samples showed the similar result, but the lacquer coated sample showed a slightly better performance.

• 한국표면공학회지
• /
• 제32권3호
• /
• pp.452-455
• /
• 1999

ORV which vaporizes LNG to NG is consisted of tube and header whose substrate is aluminum alloy. The corrosion of the tube is very severe because of sea water being used as the heating source. In this research to protect ORV substrate material, the corrosion behavior of aluminum alloys was investigated for the sacrificial role of Al-Zn alloy for ORV tubes. The electrochemical behavior of aluminum alloys in sea water was investigated. The corrosion behavior of thermally-sprayed and cladded samples were compared through salt spray tests. Al-Zn alloy can act as a sacrificial anode and cladded Al-Zn alloy has a better corrosion resistance than that of thermally sprayed one. The galvanic effect of Al-Zn to substrate material was conformed from scratched sample tests.

• 펄프종이기술
• /
• 제36권2호
• /
• pp.39-46
• /
• 2004

In this paper, the effects of roll diameter and storage time in roll form, bending method and relative humidity on curl in copy paper and inkjet coated papers are investigated. In copy paper, more MD curl is showed at smaller roll diameter and the extension of bending time. However CD curl is hardly influenced by roll diameter and bending time. At high relative humidity, especially CD curl largely reduces. All inkjet coated papers without the primary or the secondary back coating during papermaking show the increase in MD curl and slight decrease in CD curl by MD bending regardless of the winding methods(TSO, TSI). The water spray as back coating results in the remarkable reduction of CD curl regardless of the winding methods. Drying on flat dryer after spraying the moisture on back side display the most excellent effect on the reduction of CD curl.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 봄 학술논문 발표대회
• /
• pp.249-250
• /
• 2021

The use of smart equipment such as drones is increasing in construction sites. In particular, there are frequent cases where two or more drones must be used at the same time. This leads to different considerations than when operating a single unit. This study aims to analyze the requirements to be considered in the case of the operation of drones that monitor fine dust and drones that reduce fine dust in order to reduce fine dust generated in construction sites.

• 공업화학
• /
• 제34권1호
• /
• pp.69-74
• /
• 2023

화학적 제빙 방법으로 프로필렌글리콜 제빙액은 동절기 고속철도차량 하부 및 대차부에 부착되는 설빙으로 인한 결빙을 녹이는데 적용가능하다. 프로필렌글리콜 제빙액을 운행 전 고속철도차량에 철도차량 하부 및 대차부에 미리 살포하여 눈의 부착을 최소화하면 해빙 효율을 더 높일 수 있다. 고속철도의 경우 프로필렌글리콜 제빙액을 살포하여도 고속으로 운행 시 대차 표면에서 제빙액은 거의 소실되기 때문에 눈의 부착으로 인한 결빙에 대한 방빙성능은 떨어진다. 본 연구에서는 동절기 고속철도차량 하부 및 대차부에 부착되는 설빙으로 인한 결빙을 방지하기 위해 표면의 결빙을 방지하는 발수 성분을 포함하는 프로필렌글리콜 제·방빙액의 특성을 연구하였다. 발수제의 종류에 따른 점도, 융빙성능, 접촉각 및 방빙성능에 대한 비교 평가를 실시하여 고속철도차량 제·방빙액으로 최적의 물질을 찾고자 하였다. 평가 결과 에톡시실란 타입의 발수제 성분을 포함하는 제·방빙액이 가장 적합한 것으로 확인하였다.

• 한국환경과학회지
• /
• 제15권5호
• /
• pp.431-438
• /
• 2006

The strength, water permeability, and photo-degradation efficiency of NOx of porous concrete with a new concept were studied in this paper. The porous concrete was comprised of coarse aggregate of maximum size 40 mm, cement, silica fume, water and air-entraining(AE) water reducing agent. The strength of porous concrete was strongly related to its matrix proportion and compaction energy. An experimental test was carried out to study the parameters of cement proportions and silica fume content for pavement applications of porous concrete which were paving a footpath, a bikeway, a parking lot, and a driveway. The regressed equations of relation-ships between compressive strength and flexural strength, and coefficient permeability and void ratios were indicated as y=7.69x+71.74 and $y=0.42e^{0.28x}$. A method of making an air purification-functioning road, which was spraying a mixture of a photocatalyst, cement, and water onto the surface of the road, was suggested.