• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.5
• /
• pp.571-580
• /
• 2008

The influence of bacterial stress on anaerobic hydrogen-producing microorganisms was investigated in batch tests using serum bottles. Several physical and chemical stresses (i.e., heating, adding methane producing inhibitor and chemical acidification) were adapted as a pretreament of the seed sludge. In this experiment, the cultivation temperature were set at mesophilic ($35^{\circ}C$) and thermophilic conditions ($55^{\circ}C$) with adjusting pH at 5, 6, and 7 when using the mixture of food waste and activated sludge as a substrate. In conjunction with the pretreatment, hydrogen production was significantly enhanced as compared with that from untreated sludge. However, less biogas (hydrogen and methane) was produced without the pH control, resulted from the decrease of pH to below 4, mainly due to the formation of VFAs. Hydrogen and carbon dioxide gas were analyzed as main components of the biogas while methane not detected. With an application of chemical acidification, the highest hydrogen production value of 248 ml/l/day achieved at pH 7 and $35^{\circ}C$. In addition, more hydrogen gas produced when the ratio of butyric/acetic acid ratio increased. The optimum pH and temperature for hydrogen production were found to be 7 and $35^{\circ}C$, respectively.

• Journal of the Korean Chemical Society
• /
• v.54 no.1
• /
• pp.115-119
• /
• 2010

Neutral red5 (BR 5) adsorption from aqueous solution was investigated. New solid adsorbent was prepared from paper sludge incinerated at $250^{\circ}C$ during 2 hours. Experiments were carried out, in batch system, to remove RB5 dye from the synthetic waste water. Maximum adsorption of 374.98 mg/g at pH 5, at room temperature and contact time of 80 min was obtained. The Langmuir and Freundlich adsorption models were applied to interpret the equilibrium isotherm. The Freundlich isotherm fits quite well with the experimental data (with highly regression coefficient $R^2$). The incinerated sludge solid samples untreated and treated with BR5 dye were characterized by FT-IR spectrophotometer.

• Journal of Environmental Science International
• /
• v.11 no.4
• /
• pp.367-373
• /
• 2002

The polycyclic aromatic hydrocarbons(PAHs) content in sewage sludge was determined by gas chromatography linked to ion trap mass spectrometry(GC/ITMS) with five deuterated PAHs as internal standards. The minimum detection limit was from 1.66 to 7.14 pg for individual PAH by GC/ITMS. For determining total PAHs(∑PAH) in sewage sludge 84 samples from 74 waste water treatment plants in whole country were analyzed. The average content of ∑PAH far whole samples was 3,289$\pm$3,098 $\mu\textrm{g}$/kg, and ranged from 142 to maximum 20,102 $\mu\textrm{g}$/kg. According to the number of population of the city, the areas were classified as five regions, ie. big, large, middle, small, and rural area in which the waste water treated plants were grown. The contents of PAHs were 4,689$\pm$5,503, 5,839$\pm$6,401, 3,725$\pm$2,053, 2,237$\pm$2,069, and 2,475$\pm$1,489 $\mu\textrm{g}$/kg, in big, large, middle, small, and rural area, respectively.

• 한국연소학회:학술대회논문집
• /
• 2004.06a
• /
• pp.165-172
• /
• 2004

Co-incineration of coal and wastewater sludge was r;erfonn:rl in a O.lMWth bench scale circulating fluidized bed combustor(CFBC) Sludge was received from a wastewater treatment plant in a dye industrial complex in Busan. Metropolis. Moisture content of received sludge was 80%. Coal and sludge mixture was prepared with weight ratio of 90/10, 85/15 and 80/20. Co-combustion characteristics of the coal and sludge mixture demonstrated stable combustion conditions. Component analysis, incineration characteristics, boiler performance was measured before and after the test and application for commercial 59MWth CFBC boiler. The release of hazardous components such as $SO_2$ and Cl was suppressed by the presence of inherent minerals of Ca, Na, K in coal and sludge mixture. Pre-drying was not essential but it was recommended for the benefits of manageability of sludge.

• Journal of the Korea Institute of Building Construction
• /
• v.14 no.3
• /
• pp.230-236
• /
• 2014

This study was carried out to investigate the manufacturability of artificial lightweight aggregate as a way to recycle basalt powder sludge, which is a waste produced during the manufacturing process of basalt in Jeju. Powdered waste glasses and calcium carbonate are used to improve the characteristics of manufactured artificial lightweight aggregate. Especially, considering the complex factors of basalt powder sludge, powdered waste glasses, and sintering method, the amount of calcium carbonate is appropriate at the 9 wt.% in order to improve the intumescent of lightweight aggregate. Also, the amount of powdered waste glasses is effective with using less than 50 wt.% and applying the direct sintering method at the same time on decreasing the absorption of lightweight aggregate. Furthermore, in order to manufacture artificial lightweight aggregate of high quality with a low specific gravity and low water absorption, it is considered to be more effective to apply the direct sintering method after the surface of artificial lightweight aggregate is covered with powdered waste glasses.

• Journal of Korean Society of Water and Wastewater
• /
• v.31 no.3
• /
• pp.257-262
• /
• 2017

Several disposal processes for waste sludge from wastewater treatment plants such as landfill, ocean dump, incineration, reuse as fuels or fertilizers are practiced. However, ocean dumping is prohibited by international treat. New constructions of landfill sites or incineration facilities are limited by NIMBY and reuse processes are still suffering from low energy yield. Therefore, development of alternative processes for sludge disposal are currently needed. In this study, alternative technique for sludge solubilization using HVI (high voltage impulse) was suggested and verified experimentally. Sludge solubilization was carried out for 90 minutes using HVI discharge with peak voltage of 16 kV and pulse duration for 40 microsecond. About 3~9 % of MLSS and MLVSS concentration were reduced, but the soluble COD, TN, TP of the sludge increased to 372 %, 56 % and 102 % respectively. It indicates that the flocs and/or cells of the sludge were damaged by HVI. These resulted in flocs-disintegration and cells-lysis, which means the internal matters were bursted out of the flocs as well as the cells. Thus, electrical conductivity in bulk solution was increased. All of the results verified that the HVI could be used as an alternative technique for sludge solubilization processes.

• Journal of the Korea Institute of Building Construction
• /
• v.1 no.2
• /
• pp.146-153
• /
• 2001

Radical development has been made in the every field of our society for the past scores of year. Radical development of industry and lining environment has mass-produced various toxic wastes . Which comes to the fore as a serious environmental problem. The purpose of this is to suggest the optima mix design by studying the utility of a toxic waste, plated sludge as a building material and deciding the standards of quality and use of cement and evaluating the properties of mortar and concrete in which plated sludge mixed. From an experiment, compressive strength required high early strength cement or special cement. Watertightness proved to be excellent. Heavy metals, such as Cd, Pb, Cu came out below an environmental standard. Cr+6 exceeded an environmental standard under a steam curing, but came out below an environmental under a standard curing. The higher replacement rate was, the lower frost, fusion and resistance were. Thus, got better results above the goal by condition. It was possible that plated sludge was replaced and solidified to aggregate. Therefore, it is necessary to define the standards of quality on strength, replacement rate of wastes, water permeability, endurance in other to solidify plated sludge to concrete products.

• Journal of the Korean Applied Science and Technology
• /
• v.9 no.1
• /
• pp.31-40
• /
• 1992

This study is on the biodegradability of the activated sludge, which used to biodegrade Linear Alkylbenzene Sulfonate(LAS), synthetic detergents and sufactants. The activated sludge in waste water treatment plant is used to the test of biodegradation of anionic surfactants and nonionic surfactants, but it have the periodic change of the biological propety to the lapse of the time. For the puropse of controlling and adjusting of the activated sludge in biodegradation test, we collected microorganisms from the sewage plant and the soil, and then, made the activated sludge in semicontinuous aeration chamber. From determined biodegradation data, and the degree of biodegradability to the LAS, we confirmd the standardized synthetic activated sludge which have more stable biodegradability than the sewage activated sludge. In continuous biodegradation test, LAS(dodecene-1) was biodegraded more than 99%, In 7days by the standardized activated sludge.

• The KSFM Journal of Fluid Machinery
• /
• v.9 no.5 s.38
• /
• pp.22-27
• /
• 2006

Sedimentation phenomenon of suspended solids occurs by the gravitational force. Pollution particles are separated from slowly flowing waste water in clarifier. Recently, the sludge suction collector is Preferred rather than the scraper type sludge collector due to the enhancement of the clarifier efficiency. The sludge suction collector is usually operated by the user's experiences without any scientific and/or technical consideration. To evaluate the performance of sludge suction collector, the three dimensional numerical simulation was conducted by the finite volume method. To analyze the performance, the velocity vectors and the suction flow rates of the orifices were investigated. The result showed that each suction flow rate through out the collector was equivalent in the sludge suction collector and the efficiency of suction collector was good to remove high concentrated sludge in clarifier.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.415-420
• /
• 2001

Water usage in the semiconductor industries is dramatically increased by not only using bigger wafer from 8 inches to 12 inches but also by adapting new process such as Chemical Mechanical Planarization (CMP) process invented by IBM in late '80. However, The document published by International Semiconductor Association suggests the decreasing ultra pure water (UPW) use from 22 gallon/in$^2$in 1997 to 5 gallon/in$^2$ in 2012. The criteria will possibly used as exporting obstacle in the future. Generally, Solid content of CMP slurry is about 15wt%. The slurry is diluted with UPW before fed to a CMP process. When the slurry is discharged from the process as waste, it contains 0.1~0.6wt% of solid content and 9~10 at pH. The CMP waste slurry is discharged to stream with minimum treatment. In this study, to find optimum condition of coagulation for water recovery from the waste CMP slurry various condition of coagulation were examined. After coagulation far 0.1 wt% solid content of waste CMP slurry, the sludge volume was 10~15% after 30 min of sedimentation time. For the 0.5 wt%, sludge volume was 50~55% after one hour of sedimentation time. For more than 80% of water recycling, the solid content should be in the range of 0.1 to 0.2wr%. Based on the result of the turbidity removal, the Zeta Potential and the analysis of heavy metals, the optimum condition for 0.1 wr% of waste CMP slurry was with 20 mg/L of PACI at 4 to 5 of pH. The result showed that the optimum conditions fer the 0.1 wt% waste CMP slurry were 100mg/L of Alum at 4~5 of pH, 100 mg/L of MgCI$_2$at pH 10 to 11 and 100 mg/L of Ca(OH)$_2$at pH 9 to 11, respectively.