• Resources Recycling
• /
• v.23 no.4
• /
• pp.30-36
• /
• 2014

300,000 tons of waste tires are annually being produced with development of the automotive industry in Korea. Landfill and incineration treatment system are causing the economic problem through secondary environmental pollution and waste. Therefore, as one of the ways to take advantage of this, Thermo-Plastic Vulcanized (TPV) composite was prepared by the ground waste tire and plastic powders. The waste tire powder was gained by mechanical fracturing through crushers. The waste tire powder was ground by a shear crushing method and a 2-stage disk mill method instead of cutting crushing one. The waste tire powder of 50 mesh was mixed with Polypropylene(PP) in various proportions. TPVs were prepared by an extrusion, and tensile and impact tests were performed. In addition, the same experiments were repeated in 40, 80, 140 mesh conditions in order to observe size effect of waste tire powders.

• Journal of the Korea Institute of Building Construction
• /
• v.7 no.2 s.24
• /
• pp.93-98
• /
• 2007

Waste of Plastic that is waste tile and waste interlocking block result, waste tile and waste interlocking block that execute an experiment to foretell practical use possibility availability as recycled aggregate for concrete giving change in the principal parts rate for coarse aggregate recycled aggregate appeared in the world by available thing to coarse aggregate to rate 10% but necessity that present amount used establishing material application standard that is crushed than uniform application standard to receive entropy of re-fresh concrete quality is judged to be.

• Environmental Analysis Health and Toxicology
• /
• v.19 no.3
• /
• pp.315-320
• /
• 2004

Environmental waste treatment technology is transforming from incineration system to pyrolysis gasification system. And there it is necessary for our country to adapt gasification system urgently to prevent the land pollution and lack of landfill area. The objective of this study was to determine the pesticides residues of derived product of pyrolysis gasification system for recycling of waste plastic by gas chromatograph-mass selective detector and nitrogen phosphorus detector. The residual pesticides were not detected in derived product of waste recyling. But some pesticide was detected on raw level (0.02 ～ 0.05 ppm) in waste plastic sample.

• Resources Recycling
• /
• v.19 no.2
• /
• pp.63-72
• /
• 2010

The patents were searched to investigate the trend of recycling technologies about plastic waste. Database was collected from WIPS site and the range of the search was limited to patents opened in U.S.A (US), European Union (EU), Japan (JP) and Korea (KR) to september 2009. In this paper, 4,795 patents were selected by investigation abstracts and the trend of the recycling technologies relating to waste plastic were investigated through the analyzing by the years, countries, companies. The patents were occupied 65% by Japan and the most of the patents were about chemical recycling. In the case of Korea, material recycling was major in the patents of waste plastic recycling.

• Applied Chemistry for Engineering
• /
• v.28 no.1
• /
• pp.23-28
• /
• 2017

Pyrolysis characteristics of waste plastic films were investigated by using a thermogravimetric analysis and pyrolyzer-gas chromatography/mass spectrometry. Thermogravimetric analysis results revealed that the pyrolysis of waste plastic films can be divided into two distinct reactions; (1) the decomposition reaction of starch at between 200 and $370^{\circ}C$ and (2) that of other plastic polymers such as PS, PP, PE at between 370 and $510^{\circ}C$. The kinetic analysis results obtained by using the revised Ozawa method indicated that the apparent activation energy of the pyrolysis reaction of waste plastic films was also changed dramatically according to the different decomposition reactions of two major waste plastic film components. Py-GC/MS results also revealed that the typical pyrolyzates of each polymer in waste plastic films were levoglucosan (starch), terephthalic acid (PET), styrene monomer, dimer, and trimer (PS), methylated alkenes (PP), and triplet peaks (PE) composed of alkadiene/alkene/alkane. The phthalate, used as a polymer additive, was also detected on the pyrogram of waste plastic films mixture.

• Advances in concrete construction
• /
• v.5 no.6
• /
• pp.575-586
• /
• 2017

The disposal of polythene waste and fly ash is causing serious threat to the environment. Aim of this study is to decrease environmental pollution by using polythene waste and fly ash in concrete. In this study, cement was partially replaced with 0%, 5%, 10%, 15% and 20% fly ash (by weight) and plastic waste was added in shredded form at 0.6% by weight of concrete. The specimens were prepared for the concrete mix of M25 grade and water to cementitious material ratio (w/c) was maintained as 0.45. Fresh concrete property like workability was examined during casting the specimens. Hardened properties were found out by carrying out the experimental work on cubes, cylinders and beams which were cast in laboratory and their behavior under test were observed at 7 & 28 days for compressive strength and at 28 days for density, flexural strength, dynamic modulus of elasticity, abrasion resistance, water permeability and impact resistance. Overall results of this study show that addition of 0.6% (by weight of the concrete) plastic waste with 10% (by weight of cement) replacement of cement by fly ash result an improvement in properties of the concrete than conventional mix.

• Geomechanics and Engineering
• /
• v.8 no.1
• /
• pp.53-66
• /
• 2015

Plastic wastes, particularly polyethylene terephthalate (PET) generated from used bottled water constitute a worldwide environmental issue. Reusing the PET waste for geotechnical applications not only reduces environmental burdens of handling the waste, but also improves inherent engineering properties of soil. This paper investigated factors affecting shear strength improvement of PET-mixed residual soil. Four variables were considered: (i) plastic content; (ii) plastic slenderness ratio; (iii) plastic size; and (iv) soil particle size. A series of unconfined compression tests were performed to determine the optimum configurations for promoting the shear strength improvement. The results showed that the optimum slenderness ratio and PET content for shear strength improvement were 1:3 and 1.5%, respectively. Large PET pieces (i.e., $1.0cm^2$) were favorable for fine-grained residual soil, while small PET pieces (i.e., $0.5cm^2$) were favorable for coarse-grained residual soil. Higher shear strength improvement was obtained for PET-mixed coarse-grained residual soil (148%) than fine-grained residual soils (117%). The orientation of plastic pieces in soil and frictional resistance developed between soil particles and PET surface are two important factors affecting the shear strength performance of PET-mixed soil.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.4
• /
• pp.391-399
• /
• 2023

Recently, low-temperature pyrolysis technology has been studied as a recycling method for waste plastic. Low-temperature pyrolysis technology for waste plastic produces pyrolysis oil that can be used as an energy resource, but solid residue remains. Waste plastic pyrolysis residues are mostly landfilled due to their limited use. In this study, it is investigated that mixed waste plastic pyrolysis residues could be recycled into activated carbon. It was confirmed that the fixed carbon content of the residue was 33.69 % from proximate Analysis. Chemical activation was used to manufacture activated carbon. KOH was used as an activator. To investigate the effect of the mixing ratio of KOH and residue, samples were mixed at ratios of 0.5, 1.0, and 2.0. The mixed sample was chemically activated at an activation temperature of 800 ℃ for 1 hour. As a result of analyzing the characteristics of activated carbon through BET, it was confirmed that the specific surface area increased as the mixing ratio of KOH increased.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.54 no.3
• /
• pp.75-80
• /
• 2012

Gasification is a therm-chemical conversion process to convert various solid fuels into gaseous fuels under limited supply of oxygen in high temperature environment. Considering current availability of biomass resources in this country, the gasification is more attractive than any other technologies in that the process can accept various combustible solid fuels including plastic wastes. Mixed fuels of biomass and polyethylene pellets were used in gasification experiments in this study in order to assess their potential for synthesis gas production. The results showed that higher reaction temperatures were observed in mixed fuel compared to woodchip experiments. In addition, carbon monoxide, hydrogen, and methane concentrations were increased in the synthesis gas. Heating values of the synthesis gas were also higher than those from woodchip gasification. There are hundred thousand tons of agricultural plastic wastes generated in Korea every year. Co-gasification of biomass and agricultural plastic waste would provide affordable gaseous fuels in rural society.

• Resources Recycling
• /
• v.18 no.6
• /
• pp.54-59
• /
• 2009

The level manufacturing technique for refuse derived fuel (RDF) is possible to produce them itself by a domestic process which is appropriate in Korea. However, very few facilities were used for industrial combustible waste. The objective of this research is to develop the technique for refuse plastic fuel (RPF) of industrial waste. RPFs were prepared by mixing of plastic, paper and wood based on amount of regional waste. The physical properties of the RPFs prepared were investigated. RPFs prepared at mixing ratio(plastic : paper : wood) of 87.55% : 8.15% : 4.3% show the highest lower heating values in wet-base (LHVW) and the LHVW decreases as the mixing ratio of paper and wood increases.