• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.7 no.2
• /
• pp.209-222
• /
• 1997

Authors surveyed the ground water near the waste disposed from a fiberglass production factory to confirm the presence of glassfiber in the water and to determine the effect of sampling conditions and storage on the recovery of fibrous materials in the ground water. Sample was collected at every 4 hours for 48 hours consecutively. After finishing the 48 hours sample, water sampling was done from each tap after repeated turning on and off the water for 30 seconds at each time. Sample was collected in the two 1.5 liter polyethylene bottle after vigorously shaking the bottle with the same water several times with the flowing tap water. At each paired sample, one bottle was stored stand still at room temperature, and the other sample was filtered immediately after sampling. Water was filtered on the Mixed Cellulose Ester filter with negative pressure. Each sample was divided into upper and lower layer. The other bottle was stored at room temperature standstill for 7 days and filtered in the same fashion as the other pair of sample did. Each MCE filter was divided into 4 pieces and one piece was treated with acetone to make it transparent. Each prepared sample was observed by two researchers under the light and polarizing microscopy, scanning electron microscopy and energy dispersive X-ra microanalysis. Fibers were classified by the morphology and polarizing pattern under the polarizing microscope, and count was done. 1. There was a significant fluctuation in number of the fibers, but there was no specific demonstrable pattern. 2. Non-polarizing fibers frequently disappeared after 7 days's storage. But cluster of fibers were found at the wall of the same container by scratching technique. 3. Polarizing fibers were usually found in between the filter and the manicure pasted area. Possible explanations for this phenomenon will be that either these fibers are very light or have electronic polarity. Hence, these fibers are not able to be attached on the surface of slide glass. 4. Under the scanning electron microscopic examination, the fibers which are not refractive under the light microscopy were identified as glassfiber. Other fibers which is refractive under the polarizing microscopy were identified as magnesium silicate fibers. It is strongly suggested that development of standardized method of sample collection and measurement of fibrous material in the water is needed.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.33 no.4
• /
• pp.736-740
• /
• 2004

Preparation of ginseng concentrate with high content of acidic polysaccharide from white tail ginseng marc that was obtained after preparation of white tail ginseng extract. As a result of extraction of white tail ginseng under various concentrations of ethanol (0∼90%), both amount of acidic polysaccharide and extraction yield decreased by increasing the ethanol concentration. However, acidic polysaccharide extracted by water from white tail ginseng marc was increased in accordance with the increase of ethanol concentration. The optimal condition for the extraction of acidic polysaccharide from the marc was treatment of $\alpha$-amylase in 390∼650 unit/g residue/15 mL of distilled water for 5 min at 4$0^{\circ}C$. The amount of acidic polysaccharide in water extract of the marc was increased from 8.3% to 10.5% by the treatment of $\alpha$-amylase. A new ginseng extract mixture was manufactured by mixing 50% ethanol extract of white tail ginseng and water extract of alcoholic residue in the ratio of 8:2 (w/w). Crude saponin content and acidic polysaccharide content were 10.5% and 17%, respectively. The mixture had a same crude saponin content and twice acidic polysaccharide content comparing to 50% ethanol extract of white tail ginseng. It suggests that preparation of new ginseng concentrate with high content of acidic polysaccharide from white tail ginseng marc has high potencies in the utilization of waste material.

• Journal of the Korea Institute of Building Construction
• /
• v.14 no.6
• /
• pp.531-536
• /
• 2014

Recently, the amounts of dredge sea soil in south Korea have been increasing because of various maintenance works at harbors and rivers. Dredged sea soil contains various contaminants. Hence, prior to recycling the dredged sea soil, the various contaminants should be removed to prevent a secondary contamination due to the leaching of hazardous chemicals. Pretreated dredged sea soil can be buried under the ground or used for land reclamation. In this study, however, pretreated dredged sea soil was used to investigate the level of pozzolanic activity. The properties of pretreated dredged sea soil were investigated, the method for heat treatment was determined, and the compressive strength of mortar using dredged sea soil was examined. According to the XRF result, the main components of dredged sea soil were $SiO_2$ of over 55%, and $Al_2O_3$ and $SO_3$ of some amounts. Results from XRD and TG/DTA showed that pretreated dredged sea soil can be used as a pozzolanic material. When dredged sea soil was thermally treated for 90 min at $550^{\circ}C$, a compressive strength result was similar to that of control mortar.

• Applied Chemistry for Engineering
• /
• v.10 no.4
• /
• pp.543-547
• /
• 1999

The utilization of fly-ash containing high levels of the unburned carbon was investigated. In this study adsorbents were manufactured from fly-ash ad a raw material and the manufactured adsorbents were applied to the waste-water treatment including heavy metals. Varying the anthracite(Jangsung coal) content, three types of pellet were made. The carbon content of pellet increased appreciably upon the addition of anthracite. After carbonization and activation using the pellets, adsorbents showed following characteristics; the range of hardness was between 85% and 96%, iodine number was from 100 mg/g to 300 mg/g. In proportion to the anthracite addition, hardness and iodine number increased. Through the adsorption experiments of heavy metals, removal efficiencies of Pb and Cr by manufactured adsorbents were over 90%. In case of fly-ash, removal efficiencies of Pb and Cr were 31.5% and 5.6% respectively. The reason why removal capacities of manufactured adsorbents were higher than fly-ash was postulated that adsorption capability was improved by unburned carbon and $SiO_2$ which included in fly-ash during steam activation.

• Journal of the Korean GEO-environmental Society
• /
• v.10 no.7
• /
• pp.125-133
• /
• 2009

Wastewater sludge had normally filled up in land before revising the law of waste material management in 2003, which does not permit landfill of organic sludge in Korea. After the law, most sludge has been littered in the ocean up to now. However, due to the London Convention 96 Protocol, littering sludge in the ocean will also be prohibited after 2011. This Protocol makes countries find out new methods to treat wastewater sludge. There is no exception in Korea too. Many researchers have urgently try to find out better ways to treat sludge. One of ways is to make sludge recycle energy and the success of it depends on drying method. Specifically, it really depends how to make sludge dry ecologic friendly and economic efficiently. Therefore, wastewater sludge produced in Youngdong was analyzed to make it energy resources in this study. The sludge was tested to analyze the drying and chemical characteristics of it by irradiating microwave. In the result, it is sure that the sludge has little heavy metals as like as others in country side. High calories, 3370 Kcal, shows that it has good potential to be recycle energy. Moreover, weight deduction of the sludge vs. time shows long S-curve and has same deduction ratio. Specifically, S-curve can be divided by three sections based on the curvature points. There are steady state reduction ratio of weight and approximately 80% of weight duction in the second section. This results can be used to estimate the amount of sludge reduction in the full-scale microwave dryer. Drying capacity of microwave shows approximately 1.0 kg/kw/hr. It makes sure that sludge recycle energy has the potential of economic efficiency too.

• Journal of the Korean Applied Science and Technology
• /
• v.32 no.1
• /
• pp.78-84
• /
• 2015

The purpose of this study is to evaluate the removal efficiency of phosphorus from synthetic waste water by reduction and oxidation reaction of Cu-Zn metal alloy. Cu-Zn metal alloy applied in this study is composed of 40% of Zn and 60% of Cu, which is so called Muntz metal. And the fibrous type of metal alloy has approximately $200{\mu}m$ of thickness. Metal is oxidized in an aqueous solution to generate electron and metal ion. The mechanism of phosphate treatment is co-precipitation of metal ion and phosphorous ion at various pH and temperature. The treatment efficiency showed the maximum at a one cycle treatment. This result means that the surface area of reaction material is sufficient enough to get reaction equilibrium. Experiment is conducted at various pH from 5 to 9, and showed the maximum efficiency at pH 8. Phosphorous is dominated as a type of $H_2PO_4{^-}$ and $HPO_4{^{2-}}$ at this pH condition. We could not consider the temperature effect independently, because phosphorous removal efficiency showed such a complex mechanism. We could get high efficiency at lower temperature in this research.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.7 no.2
• /
• pp.57-64
• /
• 1999

The purpose of this study is to establish effective conditions for controlling $CH_4$, $N_2O$ emission from organic Waste / wastewater treatment processes. Continuous and batch experiments were conducted to treat the micro algae from polluted and eutrophicated lakes through the thermophilic oxic process. The microalgae used were mainly Microcystis sp.(collected from eutrophic lake) and Chlorella sp. (cultured in laboratory) Wasted cooking oil was added by aid-heating source. Physico-chemical components of sludges and microalgae were analyzed. In batch experiments, air supply was changed from 50ml/min to 150ml/min. The temperature. water content and drained water were affected by the air flow rate at initial stage. However, there was almost no influence of air flow rate on them in middle and last stages. At air flow rate of 100ml/min, the degradation rate of organic material was higher than that at other air flow rates. $CO_2$ concentration in exhaust was proportional to the strength of aeration, especially at initial stage when degradation was active. $CH_4$ with low concentration was detected only at starting stage when air diffusion was not enough. $N_2O$ production was not affected by variation of air supply. In continuous experiments no matter what the dewatering methods (with PAC and without PAC) and media (wood chip and reed chip) were changed, $N_2O$ was almost not affected by variation of injected air. Result showed that the reed chips using for lake purification could be used as media for thermophilic oxic process in lake and marshes area. $CO_2$ concentration was not so much affected by the change of dewatering methods and media types. $CH_4$ was not detected in the experimental period. So it can be shown that the thermophilic oxic process had been well operated in wide handling conditions regardless of media and dewatering methods.

• Journal of Bio-Environment Control
• /
• v.14 no.3
• /
• pp.218-231
• /
• 2005

This paper reviews the engineering approach needed to support humans during their long-term missions in space. This approach includes closed plant production systems under microgravity or low pressure, mass recycling, air revitalization, water purification, waste management, elimination of trace contaminants, lighting, and nutrient delivery systems in controlled ecological life support system (CELSS). Requirements of crops f3r space use are high production, edibility, digestibility, many culinary uses, capability of automation, short stems, and high transpiration. Low pressure on Mars is considered to be a major obstacle for the design of greenhouses fer crop production. However interest in Mars inflatable greenhouse applicable to planetary surface has increased. Structure, internal pressure, material, method of lighting, and shielding are principal design parameters for the inflatable greenhouse. The inflatable greenhouse operating at low pressure can reduce the structural mass and atmosphere leakage rate. Plants growing at reduced pressure show an increasing transpiration rates and a high water loss. Vapor pressure increases as moisture is added to the air through transpiration or evaporation from leaks in the hydroponic system. Fluctuations in vapor pressure will significantly influence total pressure in a closed system. Thus hydroponic systems should be as tight as possible to reduce the quantity of water that evaporates from leaks. And the environmental control system to maintain high relative humidity at low pressure should be developed. The essence of technologies associated with CELSS can support human lift even at extremely harsh conditions such as in deserts, polar regions, and under the ocean on Earth as well as in space.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.5
• /
• pp.419-427
• /
• 2018

The purpose of this study is to recycle steel slag generated from the iron producing process and to use steel slag as a construction material which is currently landfilled Steel slag is subjected to aging treatment due to the problem of expansion and collapse when it reacts with water. The Slag Atomizing Technology (SAT) method developed to solve these problems of expanding collapse of steel slag. In this study, experimental study on the emergency repair mortar using the reducing slag, electric arc furnace slag and silicon manganese slag manufactured by the SAT method is Reduced slag was shown an accelerated hydration when it was replaced with rapidly-setting cement, and the rate of substitution was equivalent to 15%. It is shown that the electric furnace oxide slag is equivalent to 100% of the natural aggregate, and it can be replaced by 15-30% when the silicon manganic slag is substituted for the electric furnace oxide slag. With the above formulation, it was possible to design the rapidly repair mortar for road use. These recycling slags can contribute on achieving sustainability of construction industry by reducing the use of cement and natural aggregates and by reducing the generation of carbon dioxide and recycling waste slag.

• Korean Chemical Engineering Research
• /
• v.47 no.3
• /
• pp.303-309
• /
• 2009

The effects of zeolite type catalysts addition on the thermal decomposition of low density polyethylene(LDPE) and ethylene vinyl acetate(EVA) resin have been studied in a thermal analyzer(TGA, DSC) and a small batch reactor. The zeolite type catalysts tested were natural zeolite, FCC catalyst, used FCC catalyst, and catalyst A. As the results of TGA experiments, addition of antifogging-agent decreased the pyrolysis point to $250^{\circ}C$, but addition of longevity-agent and clay reduced the pyrolysis rate in EVA resin. Addition of the zeolite type catalysts in the LDPE resin increased the pyrolysis rate in the order of catalyst A > used FCC catalyst > natural zeolite > LDPE resin. Addition of the zeolite type catalysts in the EVA resin increased the pyrolysis rate in the order of used FCC catalyst > natural zeolite > catalyst A > EVA resin. In the DSC experiments for LDPE resin, addition of zeolite type catalysts decreased the melting point and the heat of pyrolysis reaction in the order of catalyst A > used FCC catalyst > natural zeolite> LDPE resin. In the batch system experiments, the mixing of natural zeolite enhanced the yield of liquid fuel oil.