• 대한방사선치료학회지
• /
• 제29권2호
• /
• pp.109-117
• /
• 2017

목 적: 두경부 환자가 입체적 세기변조 회전 방사선치료 시 변화하는 체형과 환자 정열 상태를 조사하고 그에 따라 치료 시 발생하는 선량분포의 변화와 적절한 재 CT 모의치료의 필요성을 평가하고자 한다. 대상 및 방법: 근치적 목적으로 방사선 치료를 시행한 두경부암 89명에 대해 입체적 세기변조 방사선치료계획을 수립하고 치료 기간 동안의 체중을 측정하였다. 그 중 10명의 환자에 대하여 체형변화를 평가하였다. ARIA software(Offline review)를 이용하여 ramus, chin, posterior neck, clavicle 등의 landmark를 지정한 후 skin까지의 거리를 측정하여 차이를 분석하였다. 결 과: 남성 60명을 대상으로 치료시행 $17{\pm}4$회에서 re-CT 모의치료를 시행한 결과 체중 감소율이 $-6.47{\pm}3.5%$로 나타났으며, 여성 29명은 경우는 $17{\pm}5$회에서 체중 감소율이 $-5.73{\pm}2.7%$로 나타났다. 피부위축(Skin shrinkage) 변화를 관찰한 결과 대표 landmark에서의 표준편차는 C1(${\pm}0.44cm$), C3(${\pm}0.83cm$), C5(${\pm}1.35cm$)로서 0.5 kg 감소 당 약 1 mm shrinkage 발생함을 알 수 있었다. 치료 횟수에 따른 피부위축은 1~4 fx (변화 없음), 5~13 fx (-2 mm), 14~22 fx(-4 mm), 23~30 fx(-6 mm)로 나타났다. 결 론: 체형이 약 5 mm 변화하게 되면 중심부 선량은 약 3 % 이상 차이나기 시작하게 되므로 적응증치료에 필요한 CT 모의치료를 추가로 진행하여야만 한다. 또한 적극적으로 lower neck의 CT 모의치료 방법 및 set up 방법에 관하여 연구하고 새로운 고정용구(Immobilization device)의 사용도 검토할 필요가 있다.

• Design & Manufacturing
• /
• 제1권1호
• /
• pp.17-21
• /
• 2007

In the manufacture and processing of large plastic materials, product quality is tested and verified through several techniques such as injection processing, residual stress through injection molding and shrinkage. With regards to the injection molding process, common problems such as inconsistent density is seen when different points of the product are discovered to have varying thickness levels. Sink marks in product are then evident. This occurs when there is poor molding conditions caused about by poor runner and packaging systems incorporated into the process. We designed the runner system which is possible balanced filling to cavities using CAE program $Moldflow^{TM}$ and then obtained optimal processing conditions by Taguchi's Robust Design technique.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.741-744
• /
• 2000

In general there occur warpage in one way long part. Warpage is caused by differential shrinkage-Orientation Effect, Volumetric Shrinkage Effect, Differential Cooling Effect -over the part. Deco-Top is located at the top of 29"TV set and it's shape is one way long$(626{\times}130mm)$. Material is used transparency ABS resin. So we can't design ribs in this part. And we use film gate to avoid weld line. In these reasons we must develop no ribs and no warpage product. In this study we use MOLDFLOW's software-MF/FLOW, MF/COOL, MF/WARP. Using MF/FLOW, set the flow balance and gate positioning. And we can set cooling channel layout and the optimum processing condition through MF/COOL and MF/WARP. In result we reduced trials and obtained good product.

• Current Applied Physics
• /
• 제18권11호
• /
• pp.1451-1457
• /
• 2018

Injection compression molding (ICM) is an advantageous processing method for producing thin and large polymeric parts in a robust manner. In the current study, we employed the ICM process for an energy-related application, i.e., thin and large polymeric battery case. A mold for manufacturing the battery case was fabricated using injection molding. The filling behavior of molten polymer in the mold cavity was investigated experimentally. To provide an in-depth understanding of the ICM process, ICM and normal injection molding processes were compared numerically. It was found that the ICM had a relatively low filling pressure, which resulted in reduced shrinkage and warpage of the final products. Effect of the parting line gap on the ICM characteristics, such as filling pressure, clamping force, filling time, volumetric shrinkage, and warpage, was analyzed via numerical simulation. The smaller gap in the ICM parting line led to the better dimensional stability in the finished product. The ICM sample using a 0.1 mm gap showed a 76% reduction in the dimensional deflection compared with the normal injection molded part.

• 보존과학연구
• /
• 통권13호
• /
• pp.9-13
• /
• 1992

An Woljung wooden bridge structure, which assumde to has been built in the unification of shilla dynasty, was excavated at Nam-chun river basin inKyung-ju. As a result of primary investigation, the weigh loss was 70-80% and the volumetric shrinkage was up to 38% without any conservation. Between 1986 and1991, they were conserved by the two step PEG treatment at the Mokpo Conservation Institute for Maritime Archaeological Finds.

• 한국재료학회지
• /
• 제16권4호
• /
• pp.235-240
• /
• 2006

We investigated the effect of ZnO filler on the microstructure of $BaO-B_2O_3-ZnO-P_2O_5$ glass system to find an etching mechanism of barrier ribs. The sintering behavior of composites heated in the temperature range $560-600^{\circ}C$ was studied by volumetric shrinkage rate and microstructure. The etching test was carried out in $HNO_3$ solution at $50^{\circ}C$ for 10 min. The volumetric shrinkage of sintered sample decreased with the increased firing temperature because of the formation of two crystals. Glass and ZnO filler react forming the $BaZn_2(PO_4)_2$ crystal phases during the sintering process. Etching phenomenon of sintered samples by $HNO_3$ showed that the $BaZn_2(PO_4)_2$ crystal phase was strongly leached compared to glass matrix, crystal phases and fillers. Therefore, the control of interface by condition of sintering is so important to achieve etching effect in barrier ribs.

• 공업화학
• /
• 제16권5호
• /
• pp.672-676
• /
• 2005

치아수복용 고분자 복합체(polymeric dental restorative composite, PDRC)의 전치부와 구치부에의 응용 가능성을 높이고자 PDRC를 구성하는 실리카 충진재를 다양한 온도에서 열처리시켜 siloxane 기로 연결된 구조의 개질된 실리카를 제조하고 이를 PDRC 제조에 사용하였다. 제조된 PDRC의 중합 특성을 중합전환률, 중합깊이, 그리고 체적 중합수축률 등을 분석하여 고찰하였다. 실험 결과, 사용된 실리카의 열처리 온도가 높아짐에 따라 제조된 PDRC의 중합깊이는 감소하였고 체적 중합수축률과 중합전환률 값은 실리카 입자의 평균크기 감소에 따른 PDRC 내 resin matrix의 상대적 양의 증가로 인해 일정하게 증가함을 알 수 있었다.

• 한국주조공학회지
• /
• 제15권5호
• /
• pp.494-506
• /
• 1995

Test castings in plate, disc, and cubic shaped castings for 0.2wt.% carbon and stainless steel have been poured to examine the effects of the riser dimensions including riser neck on the casting soundness. Three empirical methods were chosen in risering of steel castings. A computer program of solidification analysis considering liquid and solidification contraction was developed to apply for riserdesign calculated by using their methods in plate, disc, and cubic shaped castings, and to calculate the position and dimension of shrinkage cavity in complex shaped casting. The potential of present method has been successfully demonstrated by comparing predicted cavity shapes with those obtained in a series of experimental castings. Three empirical methods can be used in a practical way to make a rapid estimation of tie minimum riser diameter, but they can not provide a criterion of casting soundness with shape and material on all occasions. The shape and position of shrinkage cavity can be successfully predicted both using the present method and using risering calculated by their methods regardless of the shape and cast material.

• 한국재료학회지
• /
• 제22권2호
• /
• pp.82-85
• /
• 2012

The effect of the alloy systems Al-Mg alloy and Al-Si alloy in this study on the characteristics of die-casting were investigated using solidification simulation software (MAGMAsoft). Generally, it is well known that the casting characteristics of Al-Mg based alloys, such as the fluidity, feedability and die soldering behaviors, are inferior to those of Al-Si based alloys. However, the simulation results of this study showed that the filling pattern behaviors of both the Al-Mg and Al-Si alloys were found to be very similar, whereas the Al-Mg alloy had higher residual stress and greater distortion as generated due to solidification with a larger amount of volumetric shrinkage compared to the Al-Si alloy. The Al-Mg alloy exhibited very high relative numbers of stress-concentrated regions, especially near the rib areas. Owing to the residual stress and distortion, defects were evident in the Al-Mg alloy in the areas predicted by the simulation. However, there were no visible defects observed in the Al-Si alloy. This suggests that an adequate die temperature and casting process optimization are necessary to control and minimize defects when die casting the Al-Mg alloy. A Tatur test was conducted to observe the shrinkage characteristics of the aluminum alloys. The result showed that hot tearing or hot cracking occurred during the solidification of the Al-Mg alloy due to the large amount of shrinkage.

• 대한치과보철학회지
• /
• 제38권6호
• /
• pp.782-790
• /
• 2000

The mainly used polymeric material for the denture is PMMA because of its cost and easiness to handle. So it was widely used material among dentists for past decades. But the acrylic-based denture materials have several common weak points such as shrinkage after curing and lack of strength. In order to solve these problems, we adapted one of hybrid system using acrylic polymer and vinyloligosilsesquioxane(POSS). POSS, which is a well known expandable monomer during polymerization process, may eventually suppress volumetric shrinkage. And the hybrid system makes it possible for the polymer to be stable in various severe conditions. Eight different kinds of samples were designed and synthesized. Each samples were characterized with dynamic mechanical analyser(DMA) to confirm their thermodynamic properties, fractured to analyze the cross-sectional morphology of the samples. And elongation, flexural and impact tests were also executed to evaluate the mechanical properties of the samples. From the results, hybrid composites had well defined crosslinked network structure compared to the widely used denture materials, and the mechanical strength improved without changing any surface condition as increment with POSS ratio in hybrid system. Fractured morphology showed homogeneous surfaces in spite of mutli component system, therefore we can conclude that the adoption of the POSS brought the reinforcement of the denture resin.