• Journal of Mechanical Science and Technology
• /
• v.20 no.3
• /
• pp.418-425
• /
• 2006

The present investigation deals with the study of the internal flow phenomena of the counterflow type vortex tube using experimental testing and numerical simulation. Visualization was carried out using the surface tracing method, injecting dye on the vortex tube wall using a needle. Vortex tube is made of acrylic to visualize the surface particle tracing and the input air pressure was varied from 0.1MPa to 0.3MPa. The experimentally visualized results on the tube show that there is an apparent sudden changing of the trajectory on the vortex tube wall which was observed in every experimental test case. This may indicate the stagnation position of the vortex flow. The visualized stagnation position moves towards the vortex generator with increase in cold flow ratio and input pressure. Three-dimensional computational study is also conducted to obtain more detailed flow information in the vortex tube. Calculated total pressure, static pressure and total temperature distributions in the vortex tube were in good agreement with the experimental data. The computational particle trace on the vortex tube wall is very similar to that observed in experiments.

• Journal of Power System Engineering
• /
• v.14 no.1
• /
• pp.16-21
• /
• 2010

This research focused on the spray and distribution characteristics of urea solution by applying flow visualization techniques and did durability and driver test on injectors as well. The spray characteristics of urea solution was observed by CCD camera. Also, the distribution characteristics of urea solution was evaluated quantitatively as well by using 3D laser scanner equipment. It was considered that it was reasonable to use the injector for gasoline engine in order to inject the urea. The best distribution chart result was observed near 45cm distance difference between catalyst and urea spray injector. As a result of trapped urea distribution chart analysis, optimal pressure and volumetric flow rates of air and urea were derived in order to improve the distribution of Urea. This information may contribute to provide fundamental data in the future.

• Journal of the Korean Society of Visualization
• /
• v.13 no.1
• /
• pp.9-14
• /
• 2015

There have been many attempts to reduce the cost of transportation. Especially, drag reduction of heavy vehicles has enormous influence on energy saving by reducing the driving power of the vehicles. In this study, the effects of drag-reducing additive devices such as side skirt, boat tail and cab-roof fairing on the drag reduction of a 5 ton truck model were experimentally investigated. The aerodynamic performance of these flow-control devices attached to heavy vehicle was evaluated through wind tunnel test. In addition, flow patterns around the truck model were visualized by using smoke tube method. The drag coefficient is reduced by up to 5.7%, 7.16% and 22.2% by the side skirt, boat tail and cab-roof fairing, respectively. The interactive effect of the side skirt and boat tail was also investigated.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.8
• /
• pp.84-91
• /
• 2005

An experimental investigation has been carried out to examine heat-transfer characteristics of an axisymmetric, under-expanded, sonic jet impinging on a flat plate and the local measurement of surface pressures and heat transfer coefficients on a plate have been achieved together with a visualization test of shock structure in a jet. Heat transfer coefficients on a plate have been found to be changed significantly depending on the under-expansion ratio as much as the nozzle-to-plate distance. These phenomena could be explained by the wall pressure measurement and the shock visualization.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.105-113
• /
• 2000

In order to clarify the final process of oil consumption, the distribution and flow of oil through each ring were visualized by induced fluorescence method. Motoring and firing test were performed in a single cylinder research engine with transparent cylinder liner. The appropriate calibration techniques were used to solve the unstability of induced light intensity as well as to know the relation of the oil film thickness and output signal. Oil behavior was also observed at dynamic state by high speed CCD camera. By analyzing the oil film thickness converted from the photographed image, it was observed that the main route of oil transport through each ring is the end gap under the usual operating condition, low engine speed and low load condition. Oil film thickness is observed to be irregular and tend to move in a body horizontally at a given piston land. And it is also found that oil flows through oil ring gap so quickly that it can be observed in a single cycle, but it flows so slowly through top and 2nd compression rings that it takes quite a long time to detect the flow.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.54 no.5
• /
• pp.79-89
• /
• 2012

The objectives of this paper were to evaluate the wind flow behind the livestock ventilation fan for small-scale wind power generation and to make flow profiles of imaginary ventilation fan for future simulation works. The field experiments using typical 50-inch fan indicated that the wind flow behind the ventilation fan had a good possibility of power generation with its high and steady wind speeds up to a distance of 2 m. The expected electricity yield was almost 101~369 W with a small (0.8 m radius) wind turbine. The decline of ventilation fan performance caused by the obstacle was also not significant with about 4 % from a distance of 2 m. The flow profiles for the computational fluid dynamics (CFD) simulation was created by combining the direction vectors analyzed from tuft visualization test and the flow predicted by the rotating fan modeling. The flow profiles are expected to provide an efficient saving of computational time and cost to design a better wind turbine system in future works.

• The Korean Journal of Applied Statistics
• /
• v.29 no.2
• /
• pp.381-388
• /
• 2016

It is common to quantify the concept of interest in the social and human sciences to test a research hypothesis. In such a case, it is strongly recommended to investigate if the procedure is appropriately designed and implemented according the research purpose since the quantification procedure highly affects the result of statistical analysis. In this work, we propose a visualization tool which enables us to check the construct validity of a measurement tool (such a questionnaire) in a concise and convenient way based on a penalized factor analysis model. We illustrate our method with numerical simulation and real data analysis.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.6
• /
• pp.563-575
• /
• 2007

This contribution contained the classical work of an open-hole tensile plate to demonstrate the performance of grating shearography and to compare with the results obtained by other full-field measurement techniques, The isotropic plate with an open-hole has often appeared in the previous contributions introducing novel full-field method and system. Grating shearography directly provided six quantitative measurands about the specimen's surface kinematics by using a single measurement set: three in-plane strains, in plane rotation, and two out-of-plane slopes. The quasi-plane wavefront of grating metrology led to high signal-to-noise ratio (SNR) and thus neither fitting nor filtering was applied, and the small shearing distance of $101{\mu}m$ could be used. The small shearing distance provided the outstanding spatial resolution of $80{\mu}m$ and sensitivity appropriate for experimental mechanics. Finally, the grating shearography enabled the visualization of the complex surface deformation around the hole and also detected parasitic flexions of the specimen in the micrometer regime during the tensile test.

• Journal of the Korean Society of Visualization
• /
• v.20 no.1
• /
• pp.45-51
• /
• 2022

Airborne particulate matter(PM) has been a global environmental problem. PM whose diameter is smaller than 10 ㎛ can permeate respiratory organs and has harmful effects on human health. Therefore, PM monitoring systems are necessary for management of PM and prevention of PM-induced negative effects. Conventional PM monitoring techniques are expensive and cumbersome to handle. In the present study, two types of PM monitoring devices were designed for measuring indoor PM concentration, portably. We experimentally investigated the performance of three commercial PM concentration measurement sensors in a closed test chamber. As a result, PM2008 sensor showed the best PM concentration measurement accuracy. Linear regression method was applied to convert PM concentration value acquired from PM2008 sensor into ground truth value. A mobile application(app.) was also created for users to check the PM concentration, easily. The mobile app. also provides safety alarm when the PM₁₀ concentration exceeds 81 ㎛/m³. The developed hand-held system enables the facile monitoring of surrounding air quality.

• Journal of the Korean Society of Visualization
• /
• v.20 no.3
• /
• pp.128-135
• /
• 2022

Cavitation occurs inevitably in marine propellers rotating at high speed in the water, which is a major cause of underwater radiated noise. Cavitation-induced noise from propellers rotating at a specific frequency not only reduces the sonar detection capability, but also exposes the ship's location, and it causes very fatal consequences for the survivability of the navy vessels. Therefore cavity inception speed (CIS) is one of the important factors determining the special performance of the ship. In this study, we present a method using computer vision that can detect and quantitatively estimate tip vortex cavitation on a propeller rotating at high speed. Based on the model test results performed in a large cavitation tunnel, the effectiveness of this method was verified.