• 한국소음진동공학회논문집
• /
• 제21권1호
• /
• pp.9-17
• /
• 2011

In this paper, the general equation of motion of damped sandwich beam with multi-viscoelastic material layer was derived based on the equation presented by Mead and Markus. The viscoelastic layer, which has characteristics of complex shear modulus, was assumed to be dominantly under shear deformation. The equation of motion of n-layered damped sandwich beam in bending could be represented by (n+3)th order ordinary differential equation. Finite element model for the n-layered damped sandwich beam was formulated and programmed using higher order shape functions. Several numerical examples were implemented to show the effects of damped material.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.189-195
• /
• 2008

The vibration isolator system(VIS) which has very low natural frequency could be designed by applying an axial compressive force to the beam-column flexure(BCF). In this paper a new shape of the BCF is suggested. It has stepwise axially varying properties by viscoelastic damping layer. So it has internal structural damping by damping layer during deformation. First the analytic solution is obtained for the BCF. And its critical load, buckling mode, stiffness and stress distributions are investigated. Also the dynamic properties of the VIS consist of the damping layered BCF are studied. Finally the optimal design procedure of damping layered BCF for the VIS is suggested. The improved performance of suggested VIS is verified by some experiments.

• 한국소음진동공학회논문집
• /
• 제11권4호
• /
• pp.37-42
• /
• 2001

Active vibration control of laminated composite plates has been carried out to design structure with maximum possible damping capacity, using piezoceramic sensor/actuators and passive constrained-layer damping treatment. The equations of motion are derived for symmetrical, multi-layer laminated plates. The damping ratio(ζ) and modal damping(2ζ$\omega$) of the first bending and torsional modes are calculated by means of iterative complex eigensolution method for both passive and active vibration control. This paper addresses a design strategy of laminated composite plate under structural vibrations.

• 한국정밀공학회지
• /
• 제18권10호
• /
• pp.148-153
• /
• 2001

Active control of flexural vibrations of smart laminated composite beams has been carried out using piezoceramic sensor/actuator and viscoelastic material. The beams with passive constrained layer damping hale been analyzed by formulating the equations of motion through the use of extended Hamilton's principle. The dynamic characteristics such as damping ratio and modal damping of the beam are calculated for various fiber orientations by means of iterative complex eigensolution method. This paper addresses a design strategy of laminated composite under flexural vibrations to design structure with maximum possible damping capacity.

• 대한기계학회논문집B
• /
• 제30권12호
• /
• pp.1155-1163
• /
• 2006

Calculation was carried out for phase velocity and deformation wave decay in a layer of viscoelastic material fixed tightly on the solid substrate. Analysis has been performed regarding the inner structure of the wave, i.e., the proportions between the vertical and horizontal displacements and their profiles. The wave characteristics depend strongly on media compressibility factor. The effect of viscous losses on parameters of the main oscillation mode was studied in detail. Results were compared with the model of coating with local deformation. A new experimental approach was made in order to measure such wave properties of a compliant coating as the dependency of deformation wave velocity on frequency and decay factor was made. The method for estimation of coating parameters enabling the drag reduction in turbulent flow was then refined.

• 한국항공운항학회지
• /
• 제15권3호
• /
• pp.6-14
• /
• 2007

In this research, vibration reduction and aeroelastic stability of a composite hingeless rotor hub flexure with viscoelastic constrained layer damping treatment(CLDT) were investigated. The composite flexures with viscoelastic CLDT were applied to hingeless rotor system to improve the in-plane stability of the lead-lag motion causing resonance. The modal test was performed and dynamic properties(natural frequency and loss factor) were acquired. Also, complex eigenvalue analysis(SOLlO7) in the NASTRAN structural analysis module was performed and compared with results of the modal test. To insure aeroelastic stability, damping ratio analyses of the hingeless rotor system with CLDT were accomplished at hovering condition due to collective pitch angle changes. Satisfactory results of increasing structural damping and stability were obtained.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.994-998
• /
• 2004

Hybrid method is used to suppress vibration of an automotive roof surface. The hybrid method proposed in this paper is implemented experimentally using both viscoelastic and piezoelectric material. The piezoelectric material is used to control the vibration of automotive structure for lower range of frequencies and the experiment of vibration control using viscoelastic material has been carried out suppress vibrations of high frequency range mark. At first the plate controlled by using hybrid method has been .implemented to verify the performance for suppressing vibration. Then the experiment has been applied to the automotive roof structure.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1996년도 추계학술대회논문집; 한국과학기술회관, 8 Nov. 1996
• /
• pp.217-223
• /
• 1996

A structure's vibration characteristic is determined by modal property of the system. Through proper vibration analysis or experiments, the structure can be modified to reduce of vibration and noise. This paper is concerned with the natural frequency and modal loss factor of sandwich plates with viscoelastic core. The effects of shear and normal strain in the viscoelastic layer are investigated on modal properties, natural frequency and modal loss factor, by changing geometry parameter and viscoelastic material property of sandwich plates. The errors of modal parameters resulting from neglecting the extension or compression in the core material for simply supported(S-S-S-S) case are compared with those for clamped(C-C-C-C) boundary condition. Finite difference method(FDM) is utilized as numerical analysis technique of square sandwich plates for fixed boundary conditions. In order to reduce computation time and increase accuracy, improved finite difference expression with fourth order truncation error was used.

• 대한기계학회논문집
• /
• 제12권5호
• /
• pp.1189-1196
• /
• 1988

본 연구에서는 내경이 각각 8.5mm와 10.3mm이며 무차원길이가 각각 710과 1158인 두 개의 시험관을 사용하는 유동장치를 제작하여 시험관 입구에서부터 유체역 학적 경계층(hydrodynamic boundary layer)과 열적 경계층(thermal boundary layer)이 동시에 발달하기 시작하는 경계조건을 형성하고 관벽에서 일정한 열 플럭스(constant heat flux)를 발생하는 조건을 부여하였다. 퇴화현상(degradation)에 대하여 비교적 안정성을 가진 폴리아크라마이드(polyacrylamide) Separan Ap273을 수도물에 용해하여 제조한 폴리머용액으로 유동특성과 열전달특성을 실험하여 열적입구길이와 열전달특성 을 규명하고자 한다.

• 한국지반공학회논문집
• /
• 제18권4호
• /
• pp.55-64
• /
• 2002

본 논문에서는 점탄-점소성 구성모델을 다층지반에서의 대형지진 발생시의 조건에 적용하기 위해 일본 고베 포트아일랜드에서 발생한 1995 Hyogoken Nanbu 지진에 대한 지진응답 해석을 수행하였다. 지진응답해석 결과 점성토의탄-점소성 모델과 점탄-점소성 모델로 계산된 가속도 기록은 포트아일랜드에서 계측된 가속도 기록과 거의 일치함을 알 수 있었으며, 점성토 지반 부근에서 점탄-점소성 모델과 탄-점소성 모델은 미세하게 다른 거동 특성을 나타내어 점소성 모델의 타당성을 확인하였다. 따라서 동적 점탄-점소성 구성모델은 대변형률 영역에서 점성토의 소성변형을 유발하는 대형 지진 등의 발생시 점성토의 증폭 및 감쇠특성의 파악을 위해 적용가능한 모델임이 입증되었다.