• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.778-784
• /
• 2002

FFU are used increasingly by the microeleceronics industry to provide clean recirculating air for the fabrication of integrated circuits and laminar flow air. There may be several hundred ffu in a large cleanroom, covering 100% of the ceiling area. Hence, there is of often knowledge in the inside and outside of the country the flu give rise to noise & vibration trouble to microelectronics industry. Noise ＆ Vibration control for satisfication about noise ＆ vibration criteria in TFT-LCD factory cleanroom be in need of exact noise & vibration data of accurence from utility & equipment that can be exert a bad influence upon cleanroom. In this pater, hence we found out noise and vibration properities of ffu by using experimental method. And, we performed noise ＆ vibration analysis about noise it vibration level in cleanroom using semiempirical method for quantative approach about noise ＆ vibration level in cleanroom.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.262-266
• /
• 2014

Military vehicle equipped with an antenna and a shelter for operating radar has a vibration exposure during driving time. This vibration would have influence on structure of military vehicle critically. In this paper, driving stability of the military vehicle is obtained through the vibration response analysis. And, vibration level of the military vehicle satisfied the military vibration specification through analysis and comparing the MIL-STD-810G. PSD and Grms data obtained by road test can be used for vibration test specification of cabinets and electronic equipment in shelter.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.587-588
• /
• 2014

Studies that the vehicle exhaust system applied by the TEG(thermal electric generator) are actively in progress in order to improve the fuel efficiency of the vehicle. Vehicle exhaust system is on a poor vibration condition, it is susceptible to TEG. This paper is about the development of vibration durability test of TEG mounted on a vehicle exhaust system. Vehicle driving tests are performed to measure the vibration condition of the vehicle exhaust system. The vibration durability test mode of TEG is evaluated using equivalent vibration energy method. The vibration durability tests of TEG are performed using the multi-axial vibration simulation table.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.247-249
• /
• 2014

The beating phenomenon occurs because of various causes, when idle vibration was happened. In this study, the beating phenomenon was divided into several parameters and controlled by the parameter. It was hypothesized that the beating parameter is related to discomfort of idle vibration. The three-down one-up method was performed for evaluating discomfort of controlled vibrations, which is widely used in the field of psychophysics. As a result in pilot test, a subject responds beating vibration more discomfort than normal idle vibration. In the future, the study will be implemented to know how much the parameters of beating signal affect to the discomfort at idle vibration in passenger vehicle.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.875-878
• /
• 2006

In the case of a vibration sensitive equipment, it require a vibration free environment to provide its proper function, therefore, it is very important to predict precisely vibration environment of microelectronics production facility due to adjacent blast work. However, it is not easy to evaluate a quantitative vibration response of structure due blast because it can be determined by the characteristics of vibration sources, propagation through rock and soil and dynamic properties of building. In this paper, vibration influence evaluation of micro-electronic Production building induced from adjacent blast activity was performed by real measurement data obtained on ground and structure at same time. And blast vibration allowable limit on ground was supposed by measurement data analysis in order to avoid operation error of precision equipments

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.2 s.119
• /
• pp.177-184
• /
• 2007

The purpose of this study is to investigate experimentally the characteristics of rotational, radial, and axial vibration for helical gears with different contact ratios. For this purpose, the gear box is specially designed and manufactured. Two helical gears with different face widths and reduction ratios are investigated. The gear vibration in each direction is measured by accelerometers attached to the gear body. Rotational vibration is the highest and radial vibration is the lowest in the gear frequencies. While the increase of rotational speed increases gear vibration, it does not always increase with torque. It is not also linearly related to the contact ratio. In addition, axial vibration is not proportional to rotational vibration.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.5
• /
• pp.1169-1181
• /
• 1994

Vibration isolation of mechanical systems, in general, is achieved through passive or active vibration isolators. Passive vibration isolator has an inherenrt performance limitation. Whereas, active vibration isolator provides significantly superior vibration-isolation performance at the cost of energy sources and sensors. Recently, in many cases, such as suspension system, precision machinery ... etc, active isolation system outweighs its limitation. Therefore, many studies, researches, and applications are carried out in this field. In this study, vibration-isolation characteristics of an active vibration control system using electromagnetic force actuator are investigated. Several control algorithms including optimal, feedforward are used for active vibration isolation. From the experimental results of each algorithm, effective control algorithms for this active vibration-isolation system are proposed.

• Korean Journal of Applied Biomechanics
• /
• v.16 no.2
• /
• pp.55-63
• /
• 2006

The purpose of this study was to investigate the effects of vibration exercise using surface electromyography. Seven male collegiate wrestlers were participated in this study. Each subject stood on the platform and the vibration was induced for 1min. WEMG8 EMG system was used to record muscle activity from Vastus lateralis, Biceps Femoris, Tibialis Anterior, and Gastrocnemius. The EMG data were sampled for 30 sec. during non-vibration and vibration half squat position, respectively. The raw data were band pass filtered to remove noise and full wave rectified Paired sample t-test were performed to see the differences of maximum and average EMG between non-vibration and vibration trials. The results indicated that vibration produced much more muscle contraction than that of non-vibration trial for all selected muscles even though the significant difference was found only from Biceps Femoris. This phenomenon was due to the individual differences so care must be taken to evaluate vibration intensity and position before personal training.

• Journal of the Korea Safety Management & Science
• /
• v.11 no.1
• /
• pp.67-73
• /
• 2009

The goal of this study was to assess the level of vibration in an walking-type cultivator, and to provide a basic information to manage the vibration exposure for farmers. The latent periods of vibration-induced white finger (VWF) were assessed through analyzing the vibration levels and frequency characteristics. Also, vibration acceleration levels based on the daily vibration exposure duration was suggested. The latent periods of vibration-induced white finger were assessed by ISO 5349 method. The latent periods were 4.5 and 10.1 years at 10% and 50% of farmer group, respectively. Also, under ACGIH (American Conference of Governmental Industrial Hygienists) standard, daily vibration exposure duration at 6.7 m/s2 of vibration acceleration has to be less than 4 hours. Therefore, education that maximum working hours should be less than 4 continuous hours is necessary for the operators of walking-type cultivators.

• Journal of the Korean Society for Railway
• /
• v.3 no.2
• /
• pp.51-61
• /
• 2000

In this study, field measurements of vibration on the structures supporting railroad track were performed. The vibration data obtained were analyzed to find out any correlation between its magnitude and several factors such as type of bridges, distance from the track, type of train, frequency characteristics, etc. As a result, the magnitude of vibration turned out to be the highest in the steel bridge, the concrete bridge and steel-concrete combined bridge were the next in descending order. It was also found that the dynamic characteristics of ground were the most important factors among several affecting vibration near by the railroad track. And the empirical ground vibration estimation equation for estimating ground vibration was developed. The proposed equation with respect to distances from the railroad could be easily used for the estimation of ground vibration at the residential areas nearby the track.