• Corrosion Science and Technology
• /
• v.10 no.2
• /
• pp.60-64
• /
• 2011

Lean duplex stainless steels have been developed in Korea for the purpose of being used in the seawater systems of industry. There are also many important seawater systems in nuclear power plants. These systems supply seawater to cooling water condenser tubes, heat exchanger tubes, related pipes and chlorine injection systems. The flow velocity of some part of seawater systems in nuclear power plants is high and damages of components from corrosion are severe. The considered lean duplex stainless steels are STS329LD (20.3Cr-2.2Ni-1.4Mo) and STS329J3L (22.4Cr-5.7Ni-3Mo) and PRENs of them are 29.4 and 37.3 respectively. Physical, mechanical and micro-structural properties of them are evaluated, and electrochemical corrosion resistance is measured quantitatively in NaCl solution. Critical Pitting Temperatures (CPT)s are measured on these alloys and pit depths are evaluated using laser microscope. Long period field tests on these alloys are now being performed, and some results are going to be presented in the following study.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.1 no.2
• /
• pp.190-201
• /
• 1989

This experimental investigation has been conducted to determine the effects of swirling angle and flow patterns on distributions of void fraction, bubble velocity and two-phase pressure drop in a vertical straight tube. Swirling angles of $0^{\circ}$ (non swirling), $30^{\circ}$, and $45^{\circ}$ were tested with air-water two components over a range of superficial air velocities. A transparent lucite tube of 38mm in internal diameter was used for the test section. The void fraction and bubble velocities were measured by means of a optical fiber probe at the upper part of the swirler in the test section. Pressure drops which seem to be closely related with flow patterns and swirling angle were measured by a differential pressure transducer. It is shown that the probability density functions of pressure drop demonstrate peculiar features for both swirling angles and flow patterns, whereas the distributions of void fraction and bubble velocities are parabolic and flat shape in the vicinity of tube center, respectively except bubbly flow in any swirling angle cases, and the void fraction increases with increasing swirling angle around the center of tube.

• International Journal of Ocean System Engineering
• /
• v.1 no.1
• /
• pp.52-59
• /
• 2011

A prototype radar display unit was implemented using inexpensive off-the-shelf components, including a nonlinear estimation algorithm for the target tracking in a clutter environment. Two custom designed boards; an analog signal processing board and a DSP board, can be plugged into an expansion slot of a personal computer (PC) to form a maritime radar display unit. Our system provided all the functionality specified in the International Maritime Organization (IMO) resolution A422(XI). The analog signal processing board was used for A/D conversion as well as rain and sea clutter suppression. The main functions of the DSP board were scan conversion and video overlay operations. A host PC was used to run the tracking algorithm of targets in clutter, using the discrete-time Bayes optimal (nonlinear, and non-Gaussian) estimation method, and the graphic user interface (GUI) software for Automatic Radar Plotting Aid (ARPA). The proposed tracking method recursively found the entire probability density function of the target position and velocity by converting into linear convolution operations.

• Journal of Mechanical Science and Technology
• /
• v.20 no.10
• /
• pp.1741-1752
• /
• 2006

A combined Streamline Upwind Petrov-Galerkin method (SUPG) and segregated finite element algorithm for solving conjugate heat transfer problems where heat conduction in a solid is coupled with heat convection in viscous fluid flow is presented. The Streamline Upwind Petrov-Galerkin method is used for the analysis of viscous thermal flow in the fluid region, while the analysis of heat conduction in solid region is performed by the Galerkin method. The method uses the three-node triangular element with equal-order interpolation functions for all the variables of the velocity components, the pressure and the temperature. The main advantage of the presented method is to consistently couple heat transfer along the fluid-solid interface. Four test cases, which are the conjugate Couette flow problem in parallel plate channel, the counter-flow in heat exchanger, the conjugate natural convection in a square cavity with a conducting wall, and the conjugate natural convection and conduction from heated cylinder in square cavity, are selected to evaluate efficiency of the presented method.

• Journal of the Korean Society of Safety
• /
• v.31 no.3
• /
• pp.28-33
• /
• 2016

Since defects in the wheels of railway vehicles, which occur due to wears with the rail, cause serious damage to the running device, the diagnostic monitoring system for condition-based maintenance is required to secure the driving safety. In this paper, we studied to apply a useful Cepstrum analysis to detect periodic structure in spectrum among the vibration signal processing techniques for the fault diagnosis of a rotating body such as wheel. In order to analyze in variations of train velocity, the Cepstrum analysis was performed after a domain change of the vibration signal from time domain to rotation angle domain. When domains change, it is important to use a interpolation for a uniform interval of the rotation angle. Finally, the Cepstrum analysis for wheel flat detection was verified by using the vibration signal including the disturbance resulting from the rail irregularities and the vibration of bogie components.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.297-301
• /
• 2006

There are more than thirty continuously recording GPS stations (CORS) have been set up at different geological sites and distributed throughout a 140 km by 140 km area in southern Taiwan beginning since 2000, and the amount of the CORS are still under increasing in this area which is recognized the suture zone between the Philippe sea plate and Eurasia plate. From the year 2000 to the end of 2005, we analyze the daily solutions to obtain the average station velocities before and after the Chengkung earthquake which occurred near eastern Taiwan at 04:38 UTC on 10 December 2003. After considering the effects of the coseismic and postseismic displacements, the difference of the horizontal components reaches 13 mm/year of the average station velocity happened in the east side of the Central Range. To the vertical component, all of the stations are risen which located in the Coastal Range, and the largest difference approaches 20mm/year.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.5
• /
• pp.47-55
• /
• 1995

Cylindrical chokes are used widely as components of hydraulic equipments. The dynamic charac teristics between flowrate and pressure drop through the cylindrical chokes were discussed by the frequency characteristics of the chokes. It was assumed no pressure recovery occured at the downstream neighborhood of the choke. The pulsating jetflow from outlet of cylindrical chokes shows very complex behaviours which are quite different from the steady jetflow but it is not clarified quantitatively. In order to utilize the chokes as a flowmeter, it is indispensable to discuss the estimation of the dynamics of pressure drop in the downstream jetflow region of cylindrical chokes. In this experimental study, the dynamic behaviours of the jetflow in the downstream region of cylindrical chokes are investigated precisely by using flow visualization. In the results of experimental sutdy, it is clarified that the retachment length depended on pressure wave is compared with it depended on velocity wave.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.9
• /
• pp.123-134
• /
• 1999

A new forming technology has been developed to fabricate near-net shape components by using aluminum alloys with globular microstructure. The estimations of filling characteristic in the forging simulation with arbitrarily shaped dies of SSM are calculated by finite element method with proposed algorithm. The proposed model and various boundary conditions for arbitrarily shaped die are investigated with the coupling calculation between the liquid phase flow and the solid phase deformation. The simulation processes with arbitrarily shaped dies are performed on the isothermal conditions and axisymmetric problems. To analyze the forging process simulation with SSM, new stress-strain relationship for semi-solid behaviour is described, and forging the liquid flow. Furthermore, For the purpose of getting net shape of SSM, it is important to be obtain a solid fraction in forging process with arbitrarily shaped dies. To produce a automotive part which have good mechanical properties, the filling pattern in accordance with die velocity and solid fraction distribution has to be estimated for arbitrarily shaped die.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.5
• /
• pp.1023-1031
• /
• 1989

An experimental study is conducted to investigate the turbulent wake flow around tubes in vertical single row tube banks. All measurements are performed at Reynolds number(Re$_{max}$) 4.2*10$_{3}$ - 2.5*10$_{4}$ with varying tube spacings from the wide pitch ratio(H/D=3.07) to the very narrow one(H/D=1.23). Flow patterns are visualized using the smoke-wire method. Mean static pressures, velocity components, and various statistical quantities of turbulence are obtained by the computer on-line technique. In the case of wide tube spacings, the near wakes of tube show similar trends to those of a single tube, and their flow indicats an anisotropic turbulence. However, as the pitch ratio decreases, wide and narrow wakes appear alternately behind adjacent tubes due to the deflected flow. Also, in the case of H/D .leq. 1.54, Karman vortex is not formed at the side of relatively wide wake.e.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.6 no.1
• /
• pp.446-467
• /
• 2012

In this paper, the analysis and design of a motion simulator (based on the approach taken by interactive virtual reality (VR) entertainment systems) is conducted. The main components of the system include a bilateral control interface, simulation and a motion simulator control scheme. The space entertainment system uses a virtual environment that enables operators to feel the actual feedback sensing and distorted motion from the virtual environment, just as they would in the real environment. The space entertainment system integrates the dynamics of the motion simulator and the virtual environment and the operator maneuvers a steering wheel to interact with the system. The multiple bilateral control schemes employ a dynamical controller, which is designed by considering the velocity and acceleration that the operator imposes on the joystick, the environmental changes imposed on the motion simulator. In addition, we develop a calculated method to evaluate the Ratio of the simulation results. It is shown that the proposed control scheme can improve the performance of the visual entertainment system. Experiments are conducted on the virtual reality entertainment system to validate the theoretical developments.