• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.4
• /
• pp.1434-1439
• /
• 2012

Vehicle is a dynamic system combined with various parameters. Dynamic characteristics of a vehicle can vary with the change of these parameters. To investigate the effect of the design parameter on vehicle handling performance the sensitivity analysis is carried out by the numerical method. The vehicle model is described by equivalent cornering stiffness that considers parameters of suspension and steering system. As the analysis results show the effect on the static and dynamic characteristics of the vehicle system, the sensitivity analysis can be used for synthesis of the design parameters to improve the vehicle handling characteristics at the design stage as well as during the vehicle test under development.

• Journal of the Korean Society of Industry Convergence
• /
• v.11 no.2
• /
• pp.71-82
• /
• 2008

In this study, 3 dimensional non-linear race car vehicle model including Chassis, steering and suspension systems were modeled by using Multi-Body Dynamics Simulation Program, DADS 9.5(Dynamic Analysis and Design System),which was used in kinematic and dynamic analysis. A full race car vehicle dynamics model using DADS program was presented and analysis was carried out to estimate the handling characteristics that may be very useful to design a race car in early design stage. The simulation of vehicle handling behavior for step steering input was simulated and compared with different design parameters: torsional stiffness of the front and rear anti roll bars, the motion ratio of the front and rear suspension system, the location of the tie rod joint, in multibody dynamic model. Therefore this simulation model before race car construction in early design step will be helpful for race car designer to save time and limited budget.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.26 no.1
• /
• pp.97-108
• /
• 2001

Design and evaluation of AGV-based material handling systems are very complicated due to the randomness and the large number of variables involved Vehicle travel time is a key parameter for designing and evaluating AGV systems. Although loaded travel time is relatively easy to estimate, determination of empty vehicle travel time is difficult due to the inherent randomness of material handling systems. Most previous studies assume that the empty vehicle travel time is the same as the loaded travel time or assume very specific environments. This paper presents new vehicle travel time models for AGV-based material transport systems. The research effort is focused on the estimation of empty vehicle travel time under various vehicle dispatching policies. Simulation experiments are used to verify the proposed travel time models.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.1
• /
• pp.121-127
• /
• 2013

In this study, suspension geometry is controlled to improve vehicle handling performance. The toe and camber of the rear suspension is controlled independently by using a double knuckle structure designed to enhance the vehicle cornering stability. Camber and toe changes in the rear wheel during high speed turning maneuver are important factors that influence the vehicle stability. Toe in the rear outer wheel plays a dominant role in cornering. A control algorithm for the camber and the toe angle input is developed to carry out the control simulation of the vehicle such as single lane change, the steady state cornering, the double lane change and the step steering simulation. Effects of the camber and toe angle control are analyzed from the computer simulations. A double lane change simulation revealed that the suspension mechanism with variable camber angle and variable toe angle decreases the peak body slip angle and peak yaw rate, 50% and 10%, respectively.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.7
• /
• pp.137-143
• /
• 1997

In this study, handling simulation of a passenger car is carried out to see the effects of suspension compliance, roll stabilizef bar and chassis flexibility. The front suspension of the car is a MacPherson strut type and the rear suspension is a multi-link type. The following five DADS models are constructed and compared to verify the effects of suspension compliance and chassis flexibility during lane change. (1) Vdhicle model without hard point compliance and stabilizer, (2) Vehicle model with hard point compoiance, (3) Vehicle model with hard point compliance and stabilizer, (4) Vehicle model with hard point compoiance, stabilizer, and one vibration mode of the chaxxis. (5) Vehicle model with hard point compliance, stabilizer, and three vibration modes of the chassis. The result shows that hard point compliance and stabilizer are significant in roll angle, and the flexibility of the chassis affects the yaw angle and yaw rate.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.3
• /
• pp.603-610
• /
• 1998

This paper develops a 7 DOF vehicle model to study the effects of the active suspension on ride. The model is used to derive a control law for the active suspension using a full state linear optimal control technique. A wheelbase preview type active suspension is also considered in the control law derivation. The time delay between wheelbases is approximated using Pade approximation technique. The ride model is extended to a 14 DOF handling model. The 14 DOF handling model includes lateral, longitudinal, yaw and four wheel spin motions in addition to the 7 DOF ride model. A control law which is derived considering only ride related parameters is used to study the effects of the active suspension on a vehicle handling. J-turn maneuver simulation results show that the active suspension has a slower response in lateral acceleration and yaw rate, a bigger steady state lateral acceleration and an oversteer tendency. Lane changing maneuver simulation results show that the active suspension has a little bigger lateral acceleration but a much smaller roll angle and roll motion. Braking maneuver simulation results show that the active suspension has a much smaller pitch angle and pitch motion.

• International Journal of Automotive Technology
• /
• v.8 no.3
• /
• pp.299-308
• /
• 2007

This study proposes a two-layer hierarchical control system that integrates active front wheel steering and four wheel braking torque control to improve vehicle handling performance and stability. The first layer is a robust model matching controller (R-MMC) based on linear matrix inequalities (LMIs), which optimizes an active front steering angle compensation and a desired yaw moment control, and calculates reference wheel slip for the target wheel according to the desired yaw moment. The second layer is a moving sliding mode controller (MSMC) that can track the reference wheel slip in a predetermined time by commanding proper braking torque on the target wheel to achieve the desired yaw moment. Since vehicle sideslip angle measurement is difficult to achieve in practice, a sliding mode observer (SMO) that requires only vehicle yaw rate as the measured input is also developed in this study. The performance and robustness of the SMO and the integrated control system are demonstrated through comprehensive computer simulations. Simulation results reveal the satisfactory tracking ability of the SMO, and the superior improved vehicle handling performance, stability and robustness of the integrated control vehicle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.1
• /
• pp.169-175
• /
• 2009

Real-time multibody vehicle dynamics software has been developed for virtual handling tests. The software can be utilized for HILS(Hardware In the Loop Simulations) and consists of three modules such as a graphical vehicle modeling preprocessor, a real time dynamics solver, and a virtual reality graphic postprocessor for virtual handling tests. In the graphical vehicle modeling preprocessor, vehicle hard point data for a suspension model are automatically converted into multibody vehicle model. In the real time dynamics solver, the efficient subsystem synthesis method is used to create multibody equations of motion for a subsystem by a subsystem. In the virtual reality graphic postprocessor, an animator has been also developed by using Matlab Virtual Reality Toolbox for virtual handling tests.

• Journal of Animal Environmental Science
• /
• v.17 no.2
• /
• pp.101-106
• /
• 2011

One hundred and forty-four cross-bred market pigs weighing approximately 110 kg were randomly divided into four groups in a 2 (handling stress; minimal vs stimulated) ${\times}$ 2 (transport vehicle type; enclosed box vs conventional open) factorial arrangement of treatments. The stimulated handling stress group received overally rough handling including electric prod stimulation during loading, transport and lairage at least once at each step. All the animals received 3-h lairage prior to slaughter. Blood and longissimus dorsi muscle (LM) samples were taken at slaughter and after overnight chilling of the carcass, respectively. Plasma concentrations of stress indicators glucose, cortisol, creatine kinase and lactate dehydrogenase were greater in the stimulated vs minimal handling stress group. There were no interactions between the handling stress and transport vehicle type in their effects on these blood variables. The incidence of pale, soft and exudative (PSE) carcass and drip loss of LM, 24-h postmortem LM pH and color including the lightness and redness were not affected by the handling stress and transport vehicle type. In conclusion, results suggest that rough handling inflicts a stimulated stress on the animal, which is manifested by increased blood concentrations of stress indicators, and therefore should be avoided for animal welfare.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.4
• /
• pp.21-28
• /
• 1997

The vehicle handling performances have a close relation with the driver's safety. And the CAT(Computer aided testing) system has been introduced as a powerful tool for improving the handling performances. In this study, a CAT system for effectively measuring and analysing the handling performances is developed based on the windows GUI(Graphic user interface) environment. Especially, in order to derive a lot of significant handling performance parameters from a series of proving ground tests, the CAT system has various functions related to real time measurement, time domain analysis, frequency domain analysis, steady state analysis and so on.