• Steel and Composite Structures
• /
• v.29 no.3
• /
• pp.333-348
• /
• 2018

An analytical method is developed for analysing the contact buckling response of infinitely long, thin corrugated plates and flat plates restrained by a Winkler tensionless foundation and subjected to linearly varying in-plane loadings, where the corrugated plates are modelled as orthotropic plates and the flat plates are modelled as isotropic plates. The critical step in the presented method is the explicit expression for the lateral buckling mode function, which is derived through using the energy method. Simply supported and clamped edges conditions on the unloaded edges are considered in this study. The acquired lateral deflection function is applied to the governing buckling equations to eliminate the lateral variable. Considering the boundary conditions and continuity conditions at the border line between the contact and non-contact zones, the buckling coefficients and the corresponding buckling modes are found. The analytical solution to the buckling coefficients is also expressed through a fitted approximate formula in terms of foundation stiffness, which is verified through previous studies and finite element (FE) method.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.12 no.1
• /
• pp.44-50
• /
• 2006

The purpose of this study is to assess the radiographic effects of normal person with contact laterally wedged insoles with strapping of varying elevations. Eight person who were randomized into group according to their birth dates and wedge elevation, participants wore contact laterally wedged insoles with strapping with elevation of 9, 15, 21mm. Standing radiographs were used to analyze the femorotibial angle for each subject, The result of repeated measures ANOVA's reveled that laterally wedged insoles with strapping of varying elevations produced significantly the femorotibial angle. The degree of change in femorotibial angle with the insole with strapping was effected by the tilt of the lateral wedge(P<0.05). We suggest that these results may be beneficial for manufacturing foot orthotic devices, such as wedged insoles, to control medial and later compartment forces in the knee varus-valgus deformity.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.11
• /
• pp.1147-1156
• /
• 2011

A contact-type area-varying capacitive displacement sensor, or CLECDiS, can measure displacements over millimeter ranges with nanometer resolution. However, a small changes in the contact condition due to the surface profile or friction, which are inherent characteristics of contact-type sensors, lead to significant distortion of the output signal. Therefore, ensuring reliable contact conditions during CLECDiS measurements is the most important area to be improved in their actual use. Herein, in order to design an instrument for ensuring reliable contact conditions, the contact condition is analyzed by characterizing the signal distortion, observing the pressure distribution between the contacting surfaces, and measuring the motional errors of the sensor using a laser Doppler vibrometer (LDV). The manufactured instrument enables a CLECDiS to be used in an ultraprecise positioning system with improved reliability.

• Polymer(Korea)
• /
• v.36 no.3
• /
• pp.338-343
• /
• 2012

Interfacial properties of commercially available soft contact lens hydrogels were studied to understand thermodynamic phenomena of protein adsorption. Hydrogel particles ($1{\times}1mm^2$) with varying water wettability were exposed to bovine serum albumin solutions for an hour. The remained albumin solutions were analyzed with Bradford assay method. The amount of protein adsorbed to hydrogels increased with protein solution concentrations following Langmuir isotherm. The partition coefficient ($P$) and Gibbs free energy cost of dehydrating the surface region by protein displacement upon adsorption increased with increasing hydrophilicity of contact lens. Understanding of physical chemistry in protein adsorption to contact lens materials enabled elucidating relationships between surface energy and albumin adsorption capacity.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.139-142
• /
• 1996

This paper presents a method of controlling contact force for deburring tasks. The cope with the nonlinearities and time-varying properties of the robot and the environment, a neural network control theory is applied to design the contact force control system. We show that the contact force between the hand and the contacting surface can be controlled by adjusting the command velocity of a robot hand, which is accomplished by the modeling of a robot and the environment as Mass-Spring-Damper system. Simulation results are shown.

• Tribology and Lubricants
• /
• v.25 no.5
• /
• pp.335-341
• /
• 2009

Elastohydrodynamic lubrication (EHL) analysis shows that film thickness is very flat in the contact area and pressure distribution is somehow similar to that of Hertzian contact pressure except the outlet region with pressure spike. These typical patterns of EHL film thickness and pressure are the cases under the steady contact conditions of applied loads and speeds. However, many engineering contacts are rather under the conditions of varying loads and contact speeds, and therefore the predictions for endurance life and performance of machine elements with steady EHL analysis are not suitable in many occasions. This study shows the differences in film thickness formation and pressure distribution between steady and transient contact conditions in several contact cases.

• Tribology and Lubricants
• /
• v.13 no.4
• /
• pp.71-78
• /
• 1997

Wear is affected by numerous factors-contact load, sliding velocity and distance, friction coefficient, material properties and environmental conditions. Among these wear factors, surface hardness is one of very important factors to determine wear. But surface hardness is varied by work hardening during repeated sliding contact. In this reason wear rate is increased or decreased with varying surface hardness, and transition of wear mechanism is happened. In this study, the surface hardening by accumulating residual stress was analyzed by considering the repeated sliding Hertzian contact model. The results showed that surface hardness was increased with increasing contact load, friction coefficient and contact number. And the depth of hardening layer, plastic layer and elastic layer depended upon contact load and number, but they didn't depend upon friction coefficient. The predicted surface hardness was about 1.5-1.8 times as hard as the material.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.841-842
• /
• 2011

• Journal of Korean Ophthalmic Optics Society
• /
• v.19 no.2
• /
• pp.145-151
• /
• 2014

Purpose: The material properties of contact lenses were measured by varying the amounts of an initiator and a cross-linking agent that are the basis for the manufacture of contact lenses, and the drug delivery effects depending on the material properties of contact lenses were compared. Methods: Contact lens samples were manufactured using HEMA by varying the concentration of the cross-linking agent and the initiator. To investigate the changes in physical characteristics depending on the material properties, the results of the experiments on the amount of drug elution, water content, refractive index, and the amount of protein adsorption were compared. Results: For the contact lenses manufactured by varying the amount of the initiator, the water content hardly changed, and the refractive index also hardly changed. The amount of drug elution was not much affected by the changes in the initiator, but the amount of elution increased as the water content increased. The amount of protein adsorption was hardly affected by the changes in the initiator, but the amount of adsorption increased as the water content decreased. Conclusions: The changes in the properties were hardly affected by the changes in the amount of the initiator, but were significantly affected by the changes in the amount of the cross-linking agent. As the amount of the cross-linking agent increased, the water content decreased, while the refractive index increased. Also, when the water content increased, the amount of drug elution increased, while the amount of protein adsorption decreased.

• Journal of the Korean Society of Physical Medicine
• /
• v.1 no.1
• /
• pp.37-47
• /
• 2006

Purpose : The purpose is to assess the effects of muscle activity of normal person with contact laterally wedged insoles with strapping of varying elevations of 9, 15, 21mm. Methods : The subjects were adult males and women who had not experienced any knee injury. They were asked to performed from isometric contraction exerciese in four postures using lateral wedged. The normalized EMG activity levels(%MVC) of the vastus lateralis, vastus medialis, tibialis anterior, soleus for the four postures of the lower extremities were compared using one way repeted measures ANOVA. Results : Comparison of EMG amplitudes across all postures revealed no significant differences among all muscles(P>0.05). Conclusion : Further studies of the effect of wedged insole angle on knee varus torque in patients with medial-lateral knee osteoarthritis are needed.