• 디지털융복합연구
• /
• 제11권2호
• /
• pp.287-297
• /
• 2013

본 논문은 OFDM 시스템을 위한 효율적인 가변길이 radix-8/4/2 FFT 구조를 제안하였다. radix-8/4/2 연산을 수행하기 위해서 제안한 FFT 프로세서는 shared memory 구조를 사용하여 하드웨어가 단순하고 적은 면적을 차지한다. 메모리 사이즈를 줄이고 데이터들 간의 충돌을 피하기 위해 효율적인 In-place 메모리 엑세스 방법을 제안한다. 또한 회전인자(twiddle factor)를 위한 ROM 기반의 lookup 테이블 방식을 대신하여 적은 면적을 차지하는 회전인자 발생기를 제안한다. 제안한 FFT 프로세서는 802.11a, 802.16a, DAB, DVB-T/H 그리고 xDSL에서 요구하는 모든 FFT 샘플링 포인트인 64, 256, 512, 1024, 2048, 4096 그리고 8192 포인트의 FFT 연산을 할 수 있다.

• 대한의용생체공학회:의공학회지
• /
• 제5권1호
• /
• pp.93-102
• /
• 1984

In this paper, the real-time compressed code generation method for the biological signal data, especially for the Electrocardiogram, is studied. For this purpose, variable length code is introduced. And from this code, we get a exactly the same reconstructed signal data as the original. Experimental results show that this program reduces the data rate by a factor of about 8, and codes the result in a form convenient for analysis.

• 대한전자공학회논문지SD
• /
• 제45권11호
• /
• pp.71-76
• /
• 2008

H.264(또는 MPEG-4/AVC pt.10) 압축 표준은 고성능 영상 압축 알고리즘으로 그 적용 범위를 넓혀 가고 있다. H.264 압축 표준의 가변길이 코드(Variable Length Code)는 데이터의 통계적 중복성의 특성을 이용하여 압축을 한다. 이러한 압축된 비트 스트림은 복호기에서 연속된 비트 스트림을 잘라내는 작업과 테이블에서 비트 스트림과 비교하는 작업을 진행하는데 순수 하드웨어 구현이 까다로운 연산부이다. 본 논문에서는 HD 영상을 실시간으로 복호 가능한 가변길이 복호기 구조를 제안한다. Exp-Golomb 복호기는 연산기로 구성되어 있으며, CAVLD는 테이블과 연산기를 혼합하여 최적화된 하드웨어로 설계하였다. 비트 스트림의 분할(parsing) 작업은 배럴 쉬프터(Barrel shifter)와 1값 감지기(First 1's detector)에서 진행되며, 이 두 유닛은 Exp-Golomb 복호기와 CAVLD가 공유하는 구조로 설계하여 불필요한 하드웨어를 제거하였다. CAVLD와 재정렬(Reorder) 유닛간의 병목현상으로 가변길이 복호기 뿐만 아니라 H.264 디코더 전체의 성능 저하가 나타나는 단점을 제거하기 위해서 CAVLD와 재정렬 유닛간 FIFO와 재정렬 유닛의 최종 출력에 메모리를 두어 병목현상을 제거하였다. 제안된 가변길이 복호기는 Verilog-HDL을 이용하여 설계하고 FPGA를 통해 검증하였다. 0.18um 표준 CMOS 공정을 사용한 합성 결과는 22,604 게이트 수이며, 동작 주파수 120MHz에서 HD 영상이 복호됨을 확인하였다.

• 한국산업융합학회 논문집
• /
• 제15권1호
• /
• pp.5-11
• /
• 2012

The Buckling of the member under compressive stress is likely to occur, which is an important factor determining the strength of structures. The objective of this study was to evaluate the member buckling strength of a circular hollow steel with ball joints and to compare with design specifications for load resistance factor of our country. Furthermore, we would like to suggest basic data for evaluation of buckling length of a circular hollow steel with ball joints according to comparative analysis. These results were summarized as follows: Buckling stress according to the test results on buckling was 1.21 times greater than LSD specifications of our country estimated the entire length of circular hollow steel with ball joints as buckling length. In addition, it was 1.16 times greater than when estimating the length except the ball as buckling length and 1.14 times grater than when excluding the ball and sleeve. Therefore, when estimating buckling stress of circular hollow steel with ball joints, their buckling length may be measured by the length except ball and sleeve.

• Journal of the Korean Data and Information Science Society
• /
• 제16권4호
• /
• pp.745-758
• /
• 2005

This paper presents a statistical analysis on the position-specific distributions of amino acid residues in transmembrane proteins. A hidden Markov model segments membrane proteins to produce segmented regions of homogeneous statistical property from variable-length amino acids sequences. These segmented residues are analyzed by using chi-square statistic and relative-entropy in order to find position-specific amino acids. This analysis showed that isoleucine and valine concentrated on the center of membrane-spanning regions, tryptophan, tyrosine and positive residues were found frequently near both ends of membrane.

• 설비공학논문집
• /
• 제18권4호
• /
• pp.320-327
• /
• 2006

Numerical analysis and experimental study are performed to investigate the effect of heat load and operating temperature on the thermal performance of several variable conductance heat pipe (VCHP) with screen meshed wick. The heat pipe is designed in 200 screen meshes, 500 mm length and 12.7 mm outer diameter tube of copper, water (4.8 g) is used as working fluid and nitrogen as non-condensible gas (NCG). Heat pipe used in this study has evaporator, condenser and adiabatic section, respectively. Analysis values and experimental data of wall temperature distribution along axial length are presented for heat transport capacity, condenser cooling water temperature change, degrees of an inclination angle and operating temperature. These analysis and experiment give the follow findings: For the same charging mass of working fluid, the operating temperature of heat pipe becomes to be high with the increasing of charging mass of NCG. When the heat flux at the evaporator section increases, the vapor pressure in the pipe rises and consequently compresses the NCG to the condenser end part and increases the active length of the condenser. From previous process, it is found out we can control the operating temperature effectively and also the analysis and experimental results are relatively coincided well.

• 한국군사과학기술학회지
• /
• 제11권3호
• /
• pp.115-122
• /
• 2008

Wu and Tsai's pixel-value differencing method and Chang and Tseng's side-match method are based on the theory that the number of bits which can be embedded is determined by the degree of the pixel's smoothness, or its proximity to the edge of the image. If pixels are located in the edge area, they may tolerate larger changes than those in smooth areas. However, both methods are subject to the fall off the boundary problem(FOBP). This study proposes a new scheme that can solve the FOBP. The experimental results demonstrate that the proposed method resolves the problem, and achieves a higher image quality index value than other methods.

• 한국의류학회지
• /
• 제17권3호
• /
• pp.475-490
• /
• 1993

Even though modem ideal body type is rather tall and slim one, most of women don't coincide with it exactly. The objective of this research was to study the optical illusion effect of clothing design line so that average Korean women can approach the modern ideal body type. This research also tried to show the more scientific method to make stimulus by computer simulation and to present quantitative data. For the experiment, 9 design variables were selected from design principal book as follows : waistline level, skirt length, horizontal line emphasis, vertical line emphasis. princess line, vertical stripe, horizontal stripe, diagonal stripe. Each variable was divided into 4 levels so that 36 experimental designs were made. Visual stimuli which same model was wearing each design were recreated by the CAD system. These were given to evaluating panels through slide projecter. Then panels compared experimental design with basic design by 'tall effect' and 'slim effect', All the data from the experiment were analyszed by ANOVA and DUNCAN test for multiple comparison to study significance, direction(positive or negative), degree, proper extent of optical illusion effect. The result showed that some designs have optical illusion effect to make better look. In addition, it proved that the stronger design variable does not mean the more optical illusion effect and there was proper extent which produce the best illusion effect in each design variable.

• ETRI Journal
• /
• 제24권2호
• /
• pp.142-152
• /
• 2002

In this paper, we propose and analyze a new multiple access protocol for a local area optical Internet based on a wavelength division multiplexing technique which uses a passive star coupler. The proposed contention-based reservation protocol can support variable-length as well as fixed-length messages for transporting Internet packets with one reservation of a minislot at the beginning of a packet transmission. The minislot is used to reserve the data channel on the basis of the slotted ALOHA protocol and the control node ensures subsequent message transmission on the same wavelength. Thus, all messages need not be broken down to many fixed-length packets, and consecutive messages are transmitted through the same wavelength. Moreover, the proposed protocol reduces the collision probability of minislots and improves wavelength utilization. We determine the maximum throughput and verify the results with simulation.

• 조명전기설비학회논문지
• /
• 제16권6호
• /
• pp.102-108
• /
• 2002

본 논문에서는 지능형 교통 시스템(ITS)의 기본 정보인 차량정보와 도로정보를 실시간으로 제공하기 위하여 루프 검지기와, 피에조 센서를 사용한 차량정보 수집 시스템의 설계를 다루었다. 루프검지기와 피에조 센서를 도로차선마다 설치하고 프로세서와 입/출력 보드를 통하여 샘플링 주기에 의하여 센서의 신호를 읽어들여 차량 및 교통정보를 생성한다. 생성된 정보는 패킷형태로 만들어져 RS232C 직렬 통신과 모뎀을 통하여 원격에 있는 교통 관제시스템으로 전송된다. 이를 위하여 EISA BUS규격의 32채널 입/출력 보드와 차량정보 수집 프로그램을 설계하고 시뮬레이션 시스템에서 확인하였다.