• Journal of Adhesion and Interface
• /
• v.18 no.3
• /
• pp.134-140
• /
• 2017

In this study, we made UV cured acrylic pressure sensitive adhesive containing silicone-urethane-acrylate (SUA) oligomer for a coating on protective film and investigated the effect of SUA oligomer content and UV-dose on adhesion properties. The results illustrated that peel strength decreases with increasing oligomer content and UV-dose, while holding power increases. The gel fractions sharply increased after UV irradiation and then remain constant with prolonged UV exposure. From peel-off test, sample S70 (70% oligomer content) shows the best peelability and removability without remaining any mark or adhesive material on the test substrate than S50 (50% oligomer content) and S60 (60% oligomer content). Sample S70 also showed a surface energy lower than $26mJ/m^2$ and a transmittance higher than 95% at UV-dose 1857 and $2270mJ/cm^2$ which met the required properties for protective film application.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.2
• /
• pp.46-56
• /
• 2014

The aim of this reviews is to introduce the information concerning design of the UV-curable jet ink composition in order to provide a good adhesive property on non-porous surface. In order to clarify the viscosity dependence of flying speed for the UV curable jet ink, rheological analysis and observation of the flying state of the ink were carried out. The relationship between ink formulas and adhesive property on non-porous surface was investigated. It was examined the adhesive property of radical polymerization type UV curable jet ink included hydrogen abstraction type photo-initiator, it was expected that the strong adhesive strength can be obtained between the ink and non-porous surface in this study. UV curable jet ink with a slight amount of water was prepared. Optimum ratio of the cationic polymerization type UV curable jet ink shows an adequate adhesive strength towards two kinds of non-porous surface such as glass, poly(vinyl chloride) when tests were conducted on the ink jet-printing test machine.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.1
• /
• pp.94-100
• /
• 2024

Recently, as interest in personal hygiene has increased due to the community spread of COVID-19 and variant viruses, fixed and potable UV germicidal equipment to sterilize indoor spaces and hand-held UV germicidal equipment to sterilize household items such as masks and mobile phones are continuously being developed and sold. However, the development and sales of the product are difficult because appropriate testing methods have not yet been established. In this situation, if an uncertified product is distributed in the market, it can cause serious harm to consumers. In this study, we investigate the photobiological risks and safety devices against UV exposure of UV germicidal equipment distributed domestically, and propose appropriate test methods for portable UV germicidal equipment based on the research results.

• Journal of Periodontal and Implant Science
• /
• v.50 no.4
• /
• pp.238-250
• /
• 2020

Purpose: This study aimed to evaluate the biocompatibility and the mechanical properties of ultraviolet (UV) cross-linked and biphasic calcium phosphate (BCP)-added collagen membranes and to compare the clinical results of ridge preservation to those obtained using chemically cross-linked collagen membranes. Methods: The study comprised an in vitro test and a clinical trial for membrane evaluation. BCP-added collagen membranes with UV cross-linking were prepared. In the in vitro test, scanning electron microscopy, a collagenase assay, and a tensile strength test were performed. The clinical trial involved 14 patients undergoing a ridge preservation procedure. All participants were randomly divided into the test group, which received UV cross-linked membranes (n=7), and the control group, which received chemically cross-linked membranes (n=7). BCP bone substitutes were used for both the test group and the control group. Cone-beam computed tomography (CBCT) scans were performed and alginate impressions were taken 1 week and 3 months after surgery. The casts were scanned via an optical scanner to measure the volumetric changes. The results were analyzed using the nonparametric Mann-Whitney U test. Results: The fastest degradation rate was found in the collagen membranes without the addition of BCP. The highest enzyme resistance and the highest tensile strength were found when the collagen-to-BCP ratio was 1:1. There was no significant difference in dimensional changes in the 3-dimensional modeling or CBCT scans between the test and control groups in the clinical trial (P>0.05). Conclusions: The addition of BCP and UV cross-linking improved the biocompatibility and the mechanical strength of the membranes. Within the limits of the clinical trial, the sites grafted using BCP in combination with UV cross-linked and BCP-added collagen membranes (test group) did not show any statistically significant difference in terms of dimensional change compared with the control group.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.295-298
• /
• 2001

This paper presents mechanical properties and weatherability of FRP pole used for a distribution line about high strength and good insulation properties. The experiment strength obtained in cantilever beam test are comparable to ES standards. The environmental factors, such as elevated temperatures, high humidity, and corrosive fluids, and ultraviolet(UV) rays, influence on the performance of Polymeric matrix composite.

• Corrosion Science and Technology
• /
• v.12 no.1
• /
• pp.27-33
• /
• 2013

According to its merits about high curing speed and low emission of volatile organic compounds, UV curable inorganic-organic coating technology has been developed as an alternative for toxic and carcinogenic chromate-based treatments for years. It is consistently observed that ultra-thin films offer excellent corrosion protection as well as paint adhesion to metals. Based on the tetra-ethylorthosilicate(TEOS) and methacryloxypropyl trimethoxysilane(MPTMS), inorganic sol was synthesized and formed hybrid networks with UV curable acrylic monomer, 6-hexanediol diacrylate(HDDA), trimethylolpropane triacrylate(TMPTA), pentaerylthritol triacrylate(PETA). Several methods were used to test their properties such as salt spray test, potentiodynamic measurement, tape peel test, etc. It was shown that anti-corrosive property and stability of storage were affected by the molecular ratios of inorganic and organic compounds. It was not only the stability of storage, but had a excellent anti-corrosive, paint adhesive, and anti-solvent properties in a final molar ratios of 0.6/0.04/0.86/0.005 (TEOS/MPTMS/Acetone/HNO3) and 0.08/0.106/0.081/0.02 (TMPTA/HDDA/PETA/photo initiator).

• Applied Chemistry for Engineering
• /
• v.28 no.1
• /
• pp.35-41
• /
• 2017

Materials exposed to outside will deteriorate due to various weathering factors such as sunlight, heat, temperature, humidity and so on. Therefore, predicting speed of degradation and life time is a very important issue. This research uses retro-reflective sheets with white and green which are most commonly used colors to conduct the outdoor exposure test and acceleration test of xenon arc in Arizona state in the United States, Chennai in India, Sanary in France and Seosan in Korea to measure the reflective performance of retro-reflection. The accelerated factor was obtained by using regression analysis through reflective values obtained from the acceleration test of xenon arc from Seosan area. Also, by using solar uv program, the accelerated factor of various climate regions were obtained and it was confirmed that the accelerated factor of Senary was 1.04, Arizona 1.82, Chennai 1.92 times higher than that of Seosan.

• Polymer(Korea)
• /
• v.29 no.6
• /
• pp.588-592
• /
• 2005

For the purpose of obtaining polycarbonate film which blocks ultra-violet ion beam was irradiated onto the surface of PC film. This method has gotten several advantages compared with the techniques, such as the protection of changes in film thickness and UV blocking material deposited onto a base film. In order to investigate UV blocking PC film, the optical and chemical characteristics, surface morphology and lightfastness were confirmed by UV/Vis, FTIR(ATR) spectroscopy, AFM, and Q-UV fasoess analyses. As a result, it was shown that the modified PC film was able to block almost all of UV region and easily control the degree of UV block. The optical changes in the film were attributed to chemical changes in PC surface by ion beam irradiation. Moreover, we expect that the modified PC film can durably block UV due to no changes in colour and UV transmittance after UV fastness test.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.23 no.3
• /
• pp.134-146
• /
• 1997

Consumers have recently preferred to purchase extensive UV intercepting products, which are waterproof and free from side effects on skin. Testing Cytoroxicity in SR method, cell survivial ratio of UV-B interceptors decreased above 0.08W/V%, and so did that of UV-A interceptors above 0.06W/V%. Also, Patch-test of inorganic UV interceptors resulted in no skin irritation even below 10.0 and 11.25. UV interceptors in the sunlight showed yellowish discoloration in 5 to 14 days. In absorption curves, UV-B was most suitable for Octyl methoxycinnamate and UV-A for Butyl methoxy dibenzoylmethane. Fro this reason, Nylonpoly UVA/UVB the material of OMC and BMDM coated with Nylon & polyethylene, was used as the organic UV interceptor. And zinc oxide and titanium dioxide was used as inorganic UV ibterceptors. The appropriate mixture ratio of ZnO and TiO2 was 6 to 4.6% of ZnO, 4% of TiO2 and 5% of Nylonpoly UVA/UVB were all combined with our sunscreen cream. The SPF value of in-vivo applied to a guinea pig was 34.9 and that of in-vivo was 38.5. Cyclomerhicone and dimerthicone were used in water-in-Silicone system. Ceryl diverhicone and sorbitan sesquioleate were used as emulsifiers and MgSO4, 7H2O, Mg-stearate/Mg-Al-stearate copolymer as emulsification stabilizers. In practical application, each SPF duration of O/W type and W/S type containing sunscreen cream of the same content showed that W/S type of sunscreen cream was 5 times as durable as the other. This product is fit for using in swimming, climbing or skiing. This research is to minimize skin trouble used by UV interceptors and to make one with proper softness, skin safety and UV intercepting efficiency.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.03a
• /
• pp.33-33
• /
• 2011

삶의 질 향상에 따른 의류 및 산업소재의 발전이 가속화되고 있는 현재 상황에 Benzotriazol 또는 Benzophenone계열의 UV-absorber들은 수많은 종류들이 개발되고 사용되고 있는 실정이지만 UV-A와 UV-B 영역을 전반적으로 protecting하고 염색 후 내열성이 떨어지고 및 색상변이(일광견뢰도 저하)를 가져오는 한계가 있다. 이에 Bezotriazine 계열의 새로운 UV-absorber에 대한 필요성에 의하여 amide와 chloride화합물에 의해 oxazinone을 합성 할 수 있었고 이를 amidine 화합물과 축합하여 S-Triazine을 고 순도로 합성 할 수 있었다. 이 화합물을 섬유 염색 시 적용이 가능토록 formulation화하여 당사에서 생산 판매되는 자동차용삼원색에 적용하여 염색하였고 현재 한국 및 유럽의 자동차 maker의 일광견뢰도 실험 방법에 따라 test한 결과 우수한 일광견뢰도를 갖는 것을 확인 할 수 있었다.