• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.III
• /
• pp.578-585
• /
• 2000

Geometrical characteristics of fresh red pepper(Capsicum annuum L.) were measured and indexed to define some important geometrical characteristics, and malformation of body and fruit stalk which are necessary for the design of the equipments for cutting, spreading and alignment of red pepper in developing a fruit stalk remover of fresh red pepper. The effects of bending of body and fruit stalk on the equipments of cutting, spreading and alignment were studied. The maximum lengths of some parts of fresh red pepper were found to be 180 mm, 125 mm, 144 mm, 67 mm and 76 mm for the body, the bent part of body, the fruit stalk, the bent part and the straight part of fruit stalk, respectively. The fresh red pepper with bending indices more than 0.4 and 0.3 for the body and the fruit stalk, respectively, was defined to be malformed based on the result of cutting rate using cutting unit; while the other ones to be normal in shape. Based on this, among the total fresh red peppers tested, 47%, 40% and 20% were found malformed for the body, the fruit stalk, and for both of the body and the fruit stalk. Malformed red peppers were poorer in spreading and alignment than normal ones, and the processed quantity was decreased with increased feed rate. The required time for the malformed peppers to pass on the alignment plate inclined at 30 increased rapidly at 8.3 Hz with increased feed rate. For the fresh red peppers with average moisture content of 85%,w.b., the maximum tensile strength between fruit stalk and body was 88.1 N; the maximum cutting resistances were 92.1 N and 94.9 N for the fruit stalk-calyx joint and body, respectively. Average coefficients of static friction were 0.99, 0.62, 0.59 and OJ, respectively, for the surfaces of rubber, galvanized iron, acryl and plywood.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2004년도 학술대회지
• /
• pp.350-354
• /
• 2004

In this study, the wear characteristics of five different dental composite resins cured by conventional halogen light and LED light sources were investigated. Five different dental composite resins of Surefil, Z100, Dyract AP, Fuji II LC and Compoglass were worn against a zirconia ceramic ball using a pin-on-disk type wear tester with 15 N contact force in a reciprocal sliding motion of sliding distance of 10 mm/cycle at 1Hz under the room temperature dry condition. The wear variations of dental composite resins were linearly increased as the number of cycles increased. It was observed that the wear resistances of these specimens were in the order of Dyract AP > Surefil > Compoglass > Z100 > Fuji II LC. On the morphological observations by SEM, the large crack formation on the sliding track of Fuji ?LC specimen was the greatest among all resin composites. Dyract AP showed less wear with few surface damage. There is no significant difference in wear performance between conventional halogen light curing and light emitting diodes curing sources. It indicates that a light emitting diodes (LED) source can replace a halogen light source as curing unit for composite resin restorations.

• 한국지반공학회논문집
• /
• 제16권1호
• /
• pp.107-116
• /
• 2000

4개 현장에 실물크기의 강관말뚝과 PC 및 PHC 말뚝의 축방향에 대한 지지거동을 알아보기 위하여, 강관말뚝에 스트레인게이지를 부착하고 항타시 계측기 손상여부를 조사하면서 동재하시험을 수행하였다. 아울러 동일한 말뚝에 대하여 2일과 7일 경과후에 정재하시험을 실시하여 하중-침하량 거동과 주면 및 선단지지력을 분리 측정하였다. 그 결과, CAPWAP 해석에 Davisson방법을 적용하여 구한 강관말뚝의 허용지지력은 정재하시험에서 구한 허용지지력 보다 약 2~33%정도 크게 나타났다. 그리고 정재하시험 결과에서 구한 산술평균한 허용지지력은 CAPWAP해석에서 Davisson's offset방법으로 구한 허용지지력보다 극한지지력에 FS=2.5를 적용하여 구한 허용지지력에 더 근접하는 경향을 보였다. 또한, 단위면적당 주면지지력은 깊이가 증가함에 따라 증가하였고, 말뚝선단부 1~2m 이내에서 발휘되는 비율이 상당히 큰 것으로 나타났다.

• 한국유체기계학회 논문집
• /
• 제17권6호
• /
• pp.109-114
• /
• 2014

After the Fukushima accident in 2011, it was revealed that nuclear power plant has the vulnerability to SBO accident and its extension situation without sufficient cooling of reactor core resulting core meltdown and radioactive material release even after reactor shutdown. Many safety systems had been developed like PAFS, hybrid SIT, and relocation of RPV and IRWST as a part of steps for the Fukushima accident, however, their applications have limitation in the situation that supply of feedwater into reactor is impossible due to high pressure inside reactor pressure vessel. The concept of hybrid heat pipe with control rod is introduced for breaking through the limitation. Hybrid heat pipe with control rod is the passive decay heat removal system in core, which has the abilities of reactor shutdown as control rod as well as decay heat removal as heat pipe. For evaluating the cooling performance hybrid heat pipe, a commercial CFD code, ANSYS-CFX was used. First, for validating CFD results, numerical results and experimental results with same geometry and fluid conditions were compared to a tube type heat pipe resulting in a resonable agreement between them. After that, wall temperature and thermal resistances of 2 design concepts of hybrid heat pipe were analyzed about various heat inputs. For unit length, hybrid heat pipe with a tube type of $B_4C$ pellet has a decreasing tendency of thermal resistance, on the other hand, hybrid heat pipe with an annular type $B_4C$ pellet has an increasing tendency as heat input increases.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.454-454
• /
• 2011

Graphene shows unusual electronic properties, such as carrier mobility as high as 10,000 $cm^2$/Vs at room temperature and quantum electronic transport, due to its electronic structure. Carrier mobility of graphene is ten times higher than that of Silicon device. On the one hand, quantum mechanical studies have continued on graphene. One of them is quantum Hall effect which is observed in graphene when high magnetic field is applied under low temperature. This is why two dimension electron gases can be formed on Graphene surface. Moreover, quantum Hall effect can be observed in room temperature under high magnetic field and shows fractional quantization values. Quantum Hall effect is important because quantized Hall resistances always have fundamental value of h/$e^2$ ~ 25,812 Ohm and it can confirm the quantum mechanical behaviors. The value of the quantized Hall resistance is extremely stable and reproducible. Therefore, it can be used for SI unit. We study to measure quantum Hall effect in CVD graphene. Graphene devices are made by using conventional E-beam lithography and RIE. We measure quantum Hall effect under high magnetic field at low temperature by using He4 gas closed loop cryostat.

• 한국전기전자재료학회논문지
• /
• 제29권8호
• /
• pp.510-515
• /
• 2016

Single-chamber solid oxide fuel cells (SC-SOFCs) consist of only one gas chamber, in which both the anode and the cathode are exposed to the same fuel-oxidant mixture. Thus, this configuration shows good thermal and mechanical resistance and allows rapid start-up and -down. In this study, the unit cell consisting of $La_{0.8}Sr_{0.2}MnO_3$ (cathode) / $Zr_{0.84}Y_{0.16}O_{2-x}$ (electrolyte) / $Ni-Zr_{0.84}Y_{0.16}O_{2-x}$ (anode) was fabricated and its electrochemical property was investigated as a function of temperature and the volume ratio of fuel and oxidant for SC-SOFCs. Impedance spectra were also investigated in order to figure out the electrical characteristics of the cell. As a result, the cell performance was governed by the polarization resistances of the electrodes. The cell exhibited an acceptable cell-performance of $86mW/cm^2$ at $800^{\circ}C$ and stable performance for 3 hs under 0.7 V.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 추계학술발표대회 논문집
• /
• pp.278-281
• /
• 2011

This system can predict the maximum output about all illumination levels so that the PV system designer can design the system having the best efficiency. For the output prediction exact about the solar cell, that is the device the basis most in the PV system, the basis has to be in order to try this way. The solution based on Lambert W-function are presented to express the transcendental current-voltage characteristic containing parasitic power consuming parameters like series and shunt resistances. A simple and efficient method for the extraction of a single current-voltage (I-V) curve under the constant illumination level is proposed. With the help of the Lambert W function, the explicit analytic expression for I is obtained. And the explicit analytic expression for V is obtained. This analytic expression is directly used to fit the experimental data and extract the device parameters. The I-V curve of the solar cell was expressed through the modeling using Lambert W-function and the numerical formula where there is the difficulty could be logarithmically expressed This method expresses with the I-V curve through the modeling using Lambert W-function which adds other loss ingredients to the equation2 as to the research afterward. And the solar cell goes as small and this I-V curve can predict the power penalty in the system unit.

• 한국농공학회지
• /
• 제26권1호
• /
• pp.29-37
• /
• 1984

This study was made to find several significant relations among various physical and mechanical properties including cone penetration resistance. The alluvial clay samples were taken at the Daebul Reclaimed Tideland in Samhomyeon, Yeongamgun, Jeonranamdo. The results of the study are summarized as follows; 1.Most samples belong to medium or high plastic, inorganic, silty clay(clay contents;32-64%, silt contents; 36-68%, sand contents; 0-3%). The specific gravities range from 2.70 to 2.73, the unit weights from 1.45 to 1. 75g/cm$^3$, the natural moisture contents from 45 to 77%, the liquid limits from 32 to 56%. It is certain that the foundation is weak because the natural moisture contents are much higher than the liquid limits. 2.It is known from the shear tests that the unconfined compression strenghs vary from 0.09 to 0. 38kg/cm2, the cohesions from 0.05 to 0. 21kg/cm2, the internal friction angles from 0 to 3˚. 3.The consolidation tests show that the initial void ratios range from 1.25 to 2.28, the compression indeices from 0.43 to 0.84, the preconsolidation loads from 0.21 to 0.74kg/cm$^2$. 4.Cone penetration resistances are usually less than 5kg/cm$^2$ from ground surface to the depth of about 8m, and from S to l0kg/cm$^2$ in the layer below about 8m to hard layer. 5.The cohesion and cone penetration resistance are in proportion to the depth of soil layer. 6.The correlations between various physical and mechanical properties including cone penetration resistance for the alluvial clay samples are as follows; a) Wn=0.944C+ l2.733 (r=0.829) b) LL=0. 728Cy+6. 991 (r=0. 873) c) PI=0.659Cy-8.168 (r=0.860) d) rt=0. 0077(272-Wn) =2.092-0. 0077Wn (r=0. 859) e) 60=0. 035wn-0 447 (r=0. 893) f) C=0.380qw+0.031 (r=0.816) g) qu=0.0707qc+0.029 (r=0.810) h) C=0.018Z+0.055 (r=O.802) I) qc=0. 415Z+1, 438 (r=0. 943)

• Tuberculosis and Respiratory Diseases
• /
• 제62권6호
• /
• pp.506-515
• /
• 2007

연구배경: 원내 폐렴의 적절한 항균제 치료를 위해서는 원발 병소에서의 원인균 규명과 항균제에 대한 내성 유무 확인이 필수적이다. 본 연구는 원내 폐렴이 의심되는 경우 기관지내시경을 통한 정량적 기관지폐포 세척술(bronchoalveolar lavage, BAL) 배양검사를 시행하여 빈번하게 분리되는 균주와 이들의 항균제 내성 현황을 알아보고자 하였다. 방 법: 2004년 1월부터 2006년 6월까지 한림의대 한강성심병원 화상 중환자실과 비화상 중환자실에서 폐 침윤의 원인규명 위해 BAL 검사를 시행하였다. 104 CFU/mL 이상의 균주가 분리되면 양성으로 판정하였다. 결 과: BAL 검사 결과 화상중환자실 27예(77.1%), 비화상중환자실 22예(59.4%)에서 배양 양성이었다. 분리되는 주요 균주는 S. aureus, Acinetobacter species 및 P. aeruginosa 였다. 화상중환자실에서 분리된 S. aureus의 경우 전부 MRSA(100%)였으며, 비화상중환자실에서는 71.4%가 MRSA로 보고되었다. P. aeruginosa의 경우 화상중환자실 및 비화상중환자실에서 amikacin 54.6% vs. 50.0%, ciprofloaxacin 100% vs. 50%, cefepime 90.9% vs. 50%, imipenem 72.7% vs. 50%, ceftazidime 45.5% vs. 25% 및 piperacillin/tazobactam 90.9% vs. 50%의 내성률을, Acinetobacter species의 경우는 amikacin 90.9% vs. 100%, ciprofloxacin 100% vs. 87.5%, cefepime 90.9% vs. 100%, imipenem 100% vs. 62.5%, ceftazidime 90.9% vs. 100% 및 piperacillin/tazobactam 81.8% vs. 62.5%의 내성률을 보여주었다. 결 론: 화상중환자실과 비화상중환자실에서 원내 폐렴이 의심되는 환자의 원인균 분포와 약제 내성 현황을 알 수 있었으며 향후 항균제 치료 전략에 도움을 줄 것으로 사료된다.

• 대한환경공학회지
• /
• 제32권2호
• /
• pp.113-120
• /
• 2010

분리막의 종류 및 환원전극의 특성에 따른 전기발생량 및 미생물 군집을 비교하기 위하여, 분리막 및 환원전극의 특성이 다른 4개의 단위전지로 구성되어 있는 공기환원전극 미생물연료전지(4 air-cathode microbial fuel cell)를 회분식 운전하였다: A) PEM(Proton Exchange Membrane)-30% Wet proofing Carbon Cloth(WC), B) AEM(Anion Exchange Membrane-WC, C) CEM(Cation Exchange Membrane)-WC, D) PEM-No Wet proofing Carbon Cloth(NC). 분리막의 종류에 상관없이 최대전력밀도는 PEM-WC(510.9 $mW/m^2$), PEM-WC(522.1 $mW/m^2$), PEM-WC(504.8 $mW/m^2$)로 유사하였으나, 환원전극이 달랐던 PEM-NC는 218.3 $mW/m^2$으로 낮게 나왔다. 내부저항은 분리막의 종류에 상관없이 20.8-28.2 ${\Omega}$으로 유사하게 나타났다. PCR-DGGE, PCA, 종다양성 분석 결과, 부유미생물 군집은 시간이 경과함에 따라 다르게 나타났으며 기존 MFC 연구에서 보고되었던 uncultured bacteria가 관찰되었다. 한편, 부착미생물 군집은 분리막의 종류에 따라 큰 변화를 나타내지 않았지만, 환원전극의 특성에 따라 군집의 변화가 관찰되었다. 따라서, 기존의 이온교환막을 분리막으로 사용하는 공기환원전극 MFC에서는 환원전극의 선택도 중요한 것으로 나타났다.