• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.79-82
• /
• 2009

This work presents a novel lighting technology based on a YAG:$Ce^{3+}$ phosphor converter with micro line lenticular structure, to accompany an array of bare LED chips on a board. This technology is especially effective in TFT-LCD backlight applications as it offers the advantages of high light radiation efficiency, low color deviation, uniform luminance distribution and compact backlight thickness. Additionally, the proposed configuration is low-cost, can be manufactured quickly, and can be mass-produced economically.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.6
• /
• pp.271-275
• /
• 2001

We investigated preparation of 1-3 PZT composites for medical ultrasonic transducer array (briefly UTA) using micro pressing method. The proposed process was using pressing PZT green sheet by PMMA micro mold obtained from X-ray lithography. Microstructures, electriacl and electro-mechanical properties of fabricated composites were analyzed. Dielectric constant at 1kHz and thickness mode electro-mechanical coupling coefficient of $6.2mm{\times}6.2mm{\times}422{\mu}m$ UTA sample were 1754 and 51%, respectively. Microstructures of sintered PZT showed dense and uniform. And PZT phases were well crystallized. Micro pressing method is a mass productive process in case of using injection molded PMMA by batch type LIGA process.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.6 s.123
• /
• pp.498-506
• /
• 2007

Using wind tunnel, experimental approaches were employed to investigate fluidelastic instability of tube bundles, subjected to uniform cross flow. There are several flow-induced vibration excitation mechanisms, such as fluidelastic instability, periodic wake shedding resonance, turbulence-induced excitation and acoustic resonance, which could cause excessive vibration in shell-and tube heat exchanges. Fluidelastic is the most important vibration excitation mechanism for heat exchanger tube bundles subjected to cross flow. The system comprised of cantilevered flexible cylinder(s) and rigid cylinders of normal square array, In order to see the characteristics of flow in tube bundles, particle image velocimetry was used. From a practical design point of view, Fluidelastic instability may be expressed simply in terms of dimensionless flow velocity and dimensionless mass-damping. The threshold flow velocity for dynamic instability of cylinder rows is evaluated and the data for design guideline is proposed for the tube bundles of normal square array.

• Journal of Broadcast Engineering
• /
• v.21 no.2
• /
• pp.169-179
• /
• 2016

Recently, MPEG-H has been standardizing for a multimedia coder in UHDTV (Ultra-High-Definition TV). Thus, the demand for not only channel-based audio contents but also object-based audio contents is more increasing, which results in developing a new technique of converting channel-based audio contents to object-based ones. In this paper, a non-uniform linear microphone array based source separation method is proposed for realizing such conversion. The proposed method first analyzes the arrival time differences of input audio sources to each of the microphones, and the spectral magnitudes of each sound source are estimated at the horizontal directions based on the analyzed time differences. In order to demonstrate the effectiveness of the proposed method, objective performance measures of the proposed method are compared with those of conventional methods such as an MVDR (Minimum Variance Distortionless Response) beamformer and an ICA (Independent Component Analysis) method. As a result, it is shown that the proposed separation method has better separation performance than the conventional separation methods.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.1
• /
• pp.15-23
• /
• 1997

An experimental investigation of two-dimensional steady natural convection cooling in a vertical open top cavity with conducting side walls of finite thickness is presented. The various heat-generating discrete heaters are located on one vertical wall of the cavity. When each heater dissipates different amount of power, the purpose of the work is to obtain the optimal array condition of the heaters. The four cases of non-uniform heating conditions are considered. The temperature fields in the cavity were visualized by the interferometer and local temperatures of the vertical wall were measured by thermocouples. The heaters were arranged in two configurations: flush-mounted on a vertical wall or protruding from the wall about 4.5 mm. The vertical wall was constructed out of copper or epoxy-resin sheet. Experiments have been conducted for air with constant Prandtl number(Pr=0.7), the aspect ratio of 4.6, 7.5, 9.5, power input in the range of 0.9 W ~ 4.2 W. For the enhancement of the cooling effectiveness, the upper and lower of vertical wall would give the better position for the heaters of higher heat flux.

• Journal of the Korean Geophysical Society
• /
• v.1 no.1
• /
• pp.51-58
• /
• 1998

A numerical program has been developed to model 2-D resistivity responses for a pole-pole array configuration in cross-hole resistivity measurements. Apparent resistivity and secondary potential were computed using the program for a cylindrical inhomogeneity in an uniform host medium excited by a point source of current in a borehole. Surprisingly apparent resistivity in the receiver hole turns out to be lower than the one of surrounding medium regardless of the conductivity of cylindrical inhomogeneity. Using only cross-hole data, therefore, it is impossible to interpret the conductivity of inhomogeneity. To overcome this problem, 3-D measurement and interpretation are necessary. If 3-D data acquisition is impossible, inline data should be used to get the information about the conductivity of inhomogeneity.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.7 no.2
• /
• pp.157-166
• /
• 1996

This paper presents the optimum termination method of a TEM Cell, which utilizes hybrid distributed termination resistor array networks. Current stream on the septum, and on the terminal end of a TEM Cell is analyzed by numerical analysis. By circuit analysis, the optimum resistor array network is designed based on the result of the analysis, which assures efficient power dissipation, and current stream traveling straight and uniform. Thermovision photos were taken for comparing the conventional termination network on which each resistor is arranged at regular intervals, with the suggested optimum termination network on which each resistor is arranged for current distribution. The comparison of the results of thermovision photos shows a good agreement with those obtained by numerical analysis.

• Journal of Information Display
• /
• v.8 no.3
• /
• pp.5-10
• /
• 2007

Twin target sputtering (TTS) system with a configuration of vertically parallel facing Al targets and a substrate holder perpendicular to the Al target plane has been designed to realize a direct Al cathode sputtering on organic light emitting diodes (OLEDs). The TTS system has a linear twin target gun with ladder type magnet array for effective and uniform confinement of high density plasma. It is shown that OLEDs with Al cathode deposited by the TTS show a relatvely lower leakage current density $({\sim}1{\times}10^{-5}mA/cm^2)$ at reverse bias of -6V, compared to that ($1{\times}10^{-2}{\sim}10^{-3}$ $mA/cm^2$ at -6V) of OLEDs with Al cathodes grown by conventional DC magnetron sputtering. In addition, it was found that Al cathode films prepared by TTS were amorphous structure with nanocrystallines due to low substrate temperature. This demonstrates that there is no plasma damage caused by the bombardment of energetic particles. This indicates that the TTS system with ladder type magnet array could be useful plasma damage free deposition technique for direct Al cathode sputtering on OLEDs or flexible OLEDs.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.1
• /
• pp.151-161
• /
• 2014

In this study, an experimental investigation has been made of the applicability of outer-layer vertical blades to real ship model. After first devised by Hutchins and Choi (2003), the outer-layer vertical blades demonstrated its effectiveness in reducing total drag of flat plate (Park et al., 2011) with maximum drag reduction of 9.6%. With a view to assessing the effect in the flow around a ship, the arrays of outer-layer vertical blades have been installed onto the side bottom and flat bottom of a 300k KVLCC model. A series of towing tank test has been carried out to investigate resistance (CTM) reduction efficiency and improvement of stern wake distribution with varying geometric parameters of the blades array. The installation of vertical blades led to the CTM reduction of 2.15~2.76% near the service speed. The nominal wake fraction was affected marginally by the blades array and the axial velocity distribution tended to be more uniform by the blades array.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.11
• /
• pp.891-897
• /
• 2018

In this paper, we propose a blind estimation scheme for the antenna spacing of nonuniform linear array MIMO radar using distributed electronic sensors based on ESPRIT. We present a blind method to separate orthogonal waveforms of a MIMO radar based on the antenna spacing estimation. The estimated orthogonal waveforms of a MIMO radar can be used for disabling opponent MIMO radars.