• 한국정밀공학회지
• /
• 제30권3호
• /
• pp.340-348
• /
• 2013

In Projection Stereolithography Apparatus (PSLA), Digital Micromirror Device (DMD) and Liquid Crystal Display (LCD) are used as a beam pattern generator. The DMD shows high resolution, but it is mostly applied in micro stereolithography due to high cost and fabricable area. In LCD, the size of pattern beam is freely controlled due to various panel sizes. The LCD, however, has some limitations such as short life time by the high power light source, non-uniform light intensity of pattern beam and low transmittance of UV-light. To solve these problems in LCD-based PSLA, a Scanbeam-SLA with LCD of 19 inches and visible LED-array is developed. In this system, the light module works like a scanner for uniform illumination. The system configuration, working principle and fabrication examples are addressed in this study.

• 대한기계학회논문집B
• /
• 제25권11호
• /
• pp.1606-1615
• /
• 2001

The present study has been conducted to investigate heat/mass transfer characteristics on a target plate fur arrays of circular impingement jets with and without effusion holes. A naphthalene sublimation method is employed to determine local heat/mass transfer coefficients on the target plate. The effusion holes are located at the center of four injection holes in the injection plate where the spent air is discharged through the effusion hole after impingement on the target plate. For the array jet impingement without effusion holes, the array jets are injected into the crossflow formed by upstream spent air because the impinged jets must flow to the open exit. For small gap distances, heat/mass transfer coefficients without effusion holes are very non-uniform due to crossflow effects and re-entrainments of spent air. However, uniform distributions and enhanced values of heat/mass transfer coefficients are obtained by installing the effusion holes. For large gap distances, the crossflow has little influence on heat/mass transfer characteristics on the target palate due to the large cross-sectional open area between the injection and target plates. Therefore, the distributions and levels of heat/mass transfer coefficients are almost the same for both cases.

• 한국항행학회논문지
• /
• 제16권2호
• /
• pp.204-210
• /
• 2012

본 논문에서 우리는 등간격 선형 어레이 (ULA : Uniform Linear Array) MIMO 레이더 시스템에 ESPRIT 알고리즘을 적용하여 전송각과 도래각을 추정하는 방법을 고려한다. 각 추정 성능을 높이기 위한 방안으로 물리적인 안테나 개수를 증가시키는 방법과 정합필터링 후의 스냅샷 수를 증가시키는 방법이 있지만 이러한 방법에는 복잡도 등의 다양한 제약이 따른다. 이에 본 논문에서는 단순히 전송, 수신 안테나 수를 적절히 분배함으로서 성능을 향상시키는 방법을 제안하고자 한다. 특히, 우리는 수신 안테나의 수가 송신 안테나 수의 약 두배가 되었을 때 최적의 성능이 얻어짐을 보인다.

• 디지털융복합연구
• /
• 제14권1호
• /
• pp.195-201
• /
• 2016

본 논문에서는 진폭-위상 복합비교 방향탐지 방식과 상관형 위상비교 방향탐지 방식의 방향탐지 정확도에 대해서 기술하였다. 복합비교 방식은 지향성 빔 특성을 갖는 스파이럴 안테나를 사용하고 상관형 방식은 블레이드 안테나를 사용하여 방위각 $360^{\circ}$를 동시에 탐지할 수 있는 균일원형배열(UCA: uniform circular array) 구조로 안테나를 배치하고 방위각의 방향탐지 정확도를 분석하였다. 3개의 안테나를 배치하는 경우 신호잡음비(SNR)가 20dB이고 파장에 대한 안테나 사이의 거리($D/{\lambda}$)가 0.5인 경우 복합비교 방식은 방향탐지 정확도가 $4.0^{\circ}$, 상관형 위상비교 방식은 방향탐지 정확도가 $1.8^{\circ}$로 나타나서 상관형 위상비교 방식이 정확도가 높은 것을 확인하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 춘계학술대회논문집
• /
• pp.368-373
• /
• 2003

This paper presents a study of low frequencies volume velocity vibration control of a smart panel in order to reduce sound transmission. A distributed piezoelectric quadratically shaped polyvinylidene fluoride (PVDF) polymer film is used as a uniform force actuator and an array of 4$\times$4 accelerometer is used as a volume velocity sensor for the implementation of a single-input single-output con rot system. The theoretical and experimental study of sensor-actuator frequency response function sho vs that this sensor-actuator arrangement provides a required strictly positive real frequency response function below about 900Hz. Direct velocity feedback could therefore be implemented with a limited gain which gives reductions of about 15㏈ in vibration level and about 8 ㏈ in acoustic power level at the (1, 1) mode of the smart Panel. It has been also shown that the shaping error of PVDF actuator could limit he stability and performance of the control system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 Techno-Fair 및 추계학술대회 논문집 전기물성,응용부문
• /
• pp.150-151
• /
• 2007

We present an one-axis parallel-plate type of bulk micromachined torsional micromirror array with single crystalline silicon (SCS) fabricated on the glass substrate. Structurally, bottom electrodes (amophous silicon) in this mirror are DRIEed along the aluminum mirror patterns on SCS, which are self-aligned with mirror plates. Tracing the history of the micromirror study, we found that few papers have been published on research for uniform driving voltages based upon the tilting direction. If there is a slight misalignment during anodic bonding between top (mirror plate) and bottom electrodes, the non-uniformity of driving voltage will be led depending on two different tilting direction. This paper discusses how much the pull-in voltages can be different due to misalignment between two electrodes. Moreover, We achieve uniform pull-in voltage regardless of misalignments in photolithography and anodic-bonding between two individual layers.

• 대한전자공학회논문지SP
• /
• 제42권4호
• /
• pp.111-118
• /
• 2005

본 논문에서는 진폭 변조 기법을 이용하여 빔포머의 저주파 대역 특성을 개선함으로써 전체적인 잡음 제거 성능을 향상하고자 한다. 일차원 등간격 선형 마이크로폰 어레이를 사용하여 잡음 제거를 할 때, 협대역의 잡음 신호에 대해서는 delay-and-sum 빔포밍으로도 적절한 빔폭을 갖는 빔패턴이 형성되므로 효과적으로 잡음을 제거할 수 있다. 그러나 광대역 잡음 신호에서는 aliasing을 피하기 위해 고주파 신호에 맞게 마이크로폰들을 등간격으로 조정하면 저주파로 갈수록 빔폭이 털어져서 저주파 대역의 잡음은 잘 제거되지 않는다. 광대역 신호에 대해 일정한 빔폭을 갖게 하는 방법들로서 서브 어레이들을 이용한 빔포밍[1][2][3][4] 이나 멀티 빔포밍[5] 등이 제안되어 왔다. 하지만, 이러한 방법들은 주파수에 따라 마이크로폰 간격을다르게 해야 한다는 원리를 기반으로 하는 것이므로 저주파 대역에서도 고주파 대역에서와 같은 좁은 빔폭을 얻기 위해서는 어레이의 크기가 커져야 하는 단점이 있다. 제안하는 알고리즘은 통신에서 주로 사용하는 진폭 변조 기법을 빔포밍에 이용한 것으로서 저주파 대역 신호를 고주파 대역으로 옮김으로써 작은 크기의 마이크로폰 어레이에서도 저주파 대역 잡음을 줄일 수 있는 장점이 있다. 등간격 선형 마이크로폰 어레이에 제안된 방법을 적용한 실험 결과에서 기존의 방법들에 비해 잡음의 저주파 성분이 잘 제거됨을 알 수 있다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제1권2호
• /
• pp.132-139
• /
• 2001

We considered the uniformity of fabricated micromirror arrays by characterizing the fabrication process and calculating the appropriate driving voltages of micromirrors used as virtual photomask in maskless photolithography. The uniformity of the micromirror array in terms of driving voltage and optical characteristics is adversely affected by factors, such as the air gap between the bottom electrode and the mirror plate, the spring shape and the deformation of the mirror plate or torsion spring. The thickness deviation of the photoresist sacrificial layer, the misalignment between mirror plate and bottom electrode, the aluminum deposition condition used to produce the spring and the mirror plate, and initial mirror deflection were identified as key factors. Their importance lies in the fact that they are related to air gap deviations under the mirror plate, asymmetric driving voltages in left and right mirror directions, and the deformation of the Al sring or mirror plate after removal of the sacrificial layer. The plasma ashing conditions used for removing the sacrificial layer also contributed to the deformation of the mirror plate and spring. Driving voltages were calculated for the pixel operation of the micromirror array, and the non-uniform characteristics of fabricated micromirrors were taken into consideration to improve driving performance reliability.

• 센서학회지
• /
• 제13권5호
• /
• pp.378-382
• /
• 2004

A micromachined fluidic structure for the introduction of liquid samples into a chip-based sensor array composed of individually addressable polymeric microbeads has been developed. The structure consists of a separately attached cover glass, a single silicon chip having micromachined channels and microbead storage cavities, and a glass carver. In our sensor array, transduction occurs via colorimetric and fluorescence changes to receptors and indicator molecules that are covalently attached to termination sites on the polymeric microbeads. Data streams are acquired for each of the individual microbeads using a CCD. One of the key parts of the structure is a passive fluid introduction system driven only by capillary force. The velocity of penetration of a horizontal capillary for the device having a rectangular cross section has been derived, and it is quite similar to the Washburn Equation calculated for a pipe with a circular cross section having uniform radius. The test results show that this system is useful in a ${\mu}$-TAS and biomedical applications.

• 정보통신설비학회논문지
• /
• 제5권1호
• /
• pp.43-59
• /
• 2006

A compact and broadband $4\times1$ array antenna was developed for 3G smart antenna system testbed. The $4\times1$ uniform linear away antenna was designed to operate at 1.885 to 2.2GHz with a total bandwidth of 315MHz. The array elements were based on the novel broadband L-probe fed inverted hybrid E-H (LIEH) shaped microstrip patch, which offers 22% size reduction to the conventional rectangular microstrip patch antenna. For steering the antenna beam, a commercial variable attenuator (KAT1D04SA002), a variable phase shifter (KPH350SC00) with four units each, and the corporate 4-ways Wilkinson power divider which was fabricated in-house were integrated to form the beamforming feed network. The developed antenna has an impedance bandwidth of 17.32% $(VSWR\leq1.5)$, 21.78% $(VSWR\leq2)$ with respect to center frequency 2.02GHz and with an achievable gain of 11.9dBi. The design antenna offer a broadband, compact and mobile solution for a 3G smart antenna testbed to fully characterized the IMT-2000 radio specifications and system performances.