• Geomechanics and Engineering
• /
• 제14권3호
• /
• pp.233-240
• /
• 2018

Pullout tests are usually employed to determine the ultimate bearing capacity of reinforced soil, and the load-displacement curve can be obtained easily. This paper presents an analytical solution for predicting the full-range mechanical behavior of a buried planar reinforcement subjected to pullout based on a bi-linear bond-slip model. The full-range behavior consists of three consecutive stages: elastic stage, elastic-plastic stage and debonding stage. For each stage, closed-form solutions for the load-displacement relationship, the interfacial slip distribution, the interfacial shear stress distribution and the axial stress distribution along the planar reinforcement were derived. The ultimate load and the effective bond length were also obtained. Then the analytical model was calibrated and validated against three pullout experimental tests. The predicted load-displacement curves as well as the internal displacement distribution are in closed agreement with test results. Moreover, a parametric study on the effect of anchorage length, reinforcement axial stiffness, interfacial shear stiffness and interfacial shear strength is also presented, providing insights into the pullout behaviour of planar reinforcements of MSE structures.

• 한국지진공학회논문집
• /
• 제10권2호
• /
• pp.1-10
• /
• 2006

형상비가 상대적으로 작은 철근콘크리트 교각에 지진작용으로 인한 반복 횡하중이 작용하면 초기단계와 중간단계의 변위에서는 휨 거동을 보이다가 최종변위단계에서는 전단에 의해 파괴되는 휨-전단 거동을 보인다. 휨-전단 파괴거동을 보이는 교각은 휨 파괴거동을 보이는 교각에 비하여 연성능력이 저하되므로, 내진설계 또는 내진성능평가에서 극한변위를 해석적으로 결정하기 위해서는 휨성능곡선과 함께 전단성능곡선 모델을 적용하여야 한다. 본 논문에서는 원형교각에 대한 기존 모델을 수정한 전단성능곡선 모델을 제안하였고, CALTRANS 모델, Aschheim등의 모델, Priestley 등의 모델, 제안모델의 특징을 비교하였다. 또 국내에서 수행된 실물크기 기둥 실험체를 대상으로 전단성능곡선 모델을 평가하였다. 제한된 범위의 소수 실험결과에 대한 적용으로서 일반화하기는 어려울 것이지만, 실험결과와 비교 검토한 결과 제안모델이 파괴형태의 예측과 변위성능 예측의 정확도에서 매우 우수한 것으로 평가되었다.

• 한국지진공학회논문집
• /
• 제6권3호
• /
• pp.11-21
• /
• 2002

유연도법 섬유요소모델을 통하여 반복하중을 받는 철근콘크리트 교각의 비탄성 이력 거동을 추적하고 직접적인 방법에 의해 변위연성도 평가를 수행하였다. 철근 콘크리트 교각의 극한상태까지의 비탄성 거동을 합리적으로 추적하기 위해 인장강성거동, 기둥-기초면의 불연속 변위 등을 고려하여 철근과 콘크리트의 평균응력-평균변형률 관계, 접촉면요소 등을 실험과 잘 일치하는 기존의 해석 모델을 수정, 적용하였다. 또한 수치해석시 간편하게 적용할 수 있는 직접적인 방법에 의하여 교각의 연성능력을 평가하였으며, 항복변위 및 극한변위의 산출에 영향을 미치는 적분점의 위치, 콘크리트 압쇄 후 강루 철근의 low-cycle fatigue에 의한 파단 시점 등에 대하여 유연도법 섬유요소모델에 적용할 수 있는 값들을 제시하였다. 해석에 의한 변위연성도는 10%이내의 오차를 보이므로, 적용한 해석기법 및 모델에 의한 항복변위 및 극한변위의 평가는 타당하다고 할 수 있다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제12권1호
• /
• pp.325-342
• /
• 2020

The current study is focused on the evaluation of the ultimate strength of stiffened panels found in ship hull structures that are subjected to combined uniaxial thrust, in-plane and out-of-plane bending moments. This loading condition, which is in general ignored when performing buckling checks, applies to representative control geometries (stiffener with attached plating) as a consequence of the linearly varying normal stresses along the ship's depth induced by the hull-girder vertical bending moment. The problem is generalized by introducing a non-uniform thrust described by a displacement ratio and rotation angle and by introducing the slenderness ratios, within the practical range of interest. The formed design space is explored through methods sourcing from Design of Experiments and by applying non-linear finite element procedures. Surrogate empirical models have been constructed through regression analysis and Response Surface Methods. An additional empirical model is provided to the literature for predicting the ultimate strength under uniaxial thrust. The numerical experimentation has shown that is a significant influence on the ultimate strength of stiffened panels as the thrust non-uniformity increases.

• 한국구조물진단유지관리공학회 논문집
• /
• 제10권5호
• /
• pp.87-98
• /
• 2006

본 연구는 풍화암에 근입된 영구 앵커의 극한인발력에 관한 연구를 수행하기 위하여 현장에서 실규모 인발시험을 실시한 실험 결과이다. 현장 실물 실험에서는 정착길이가 다른 4개의 앵커에 대한 하중-변위 곡선으로부터 극한인발력을 산정하였다. 또한, 앵커의 수용 여부를 결정하기 위해 단계별 최대하중에서 15분 동안의 크리프 시험을 실시하여 극한하중까지의 크리프치를 평가하였다. 그리고 풍화암에 근입된 영구 앵커의 파괴메카니즘을 규명하기 위해 지표면에 다이얼게이지를 설치하여 하중 변화에 따른 지반의 파괴 거동 범위를 측정하였다.

• Structural Engineering and Mechanics
• /
• 제66권6호
• /
• pp.783-792
• /
• 2018

This paper presents a detailed theoretical study of the sleeved compression members based on a mechanical model. In the mechanical model, the core protrusion above sleeve and the contact force between the core and sleeve are specially taken into account. Via the theoretical analyses, load-displacement relationships of the sleeved compression members are obtained and verified by the experimental results. On the basis of the core moment distribution changing with the increase of the applied axial load, failure mechanism of the sleeved compression members is assumed and proved to be consistent with the experimental results in terms of the failure modes and the ultimate bearing capacities. A parametric study is conducted to quantify how essential factors including the core protrusion length above sleeve, stiffness ratio of the core to sleeve, core slenderness ratio and gap between the core and sleeve affect the mechanical behaviors of the sleeved compression members, and it is concluded that the constrained effect of the sleeve is overestimated neglecting the core protrusion; the improvement of ultimate bearing capacity for the sleeved compression member is considered to be decreasing with the decrease of the core slenderness ratio and for the sleeved compression member with core of small slenderness ratio, small gap and small stiffness ratio are preferred to obtain larger ultimate bearing capacity and stiffness.

• Steel and Composite Structures
• /
• 제14권6호
• /
• pp.587-604
• /
• 2013

There are few technical documents regulated structural performance and engineering criteria in domestic market for Structural insulated panels in Korea. This paper was focused to identify fundamental performance under monotonic loading and cyclic loading for SIPs in shear wall application. Load-displacement responses of total twelve test specimens were recorded based on shear stiffness, strength, ultimate load and displacement. Finally energy dissipation of each specimen was analyzed respectively. Monotonic test results showed that ultimate load was 44.3 kN, allowable shear load was 6.1 kN/m, shear stiffness was 1.2 MN/m, and ductility ratio was 3.6. Cyclic test was conducted by two kinds of specimens: single panel and double panels. Cyclic loading results, which were equivalent to monotonic loading results, showed that ultimate load was 45.4 kN, allowable shear load was 6.3 kN/m. Furthermore the accumulated energy dissipation capability for double panels was as 2.3 times as that for single panel. Based on results of structural performance test, it was recommended that the allowable shear load for panels should be 6.1 kN/m at least.

• 한국안전학회지
• /
• 제17권4호
• /
• pp.52-60
• /
• 2002

Failure criterion is a parameter to represent the resistance to failure of locally wall thinned pipe, and it depends on material characteristics, defect geometry, applied loading type, and failure mode. Therefore, accurate prediction of integrity of wall thinned pipe requires a failure criterion adequately reflected the characteristics of defect shape and loading in the piping system. In the present study, the finite element analysis was performed and the results were compared with those of pipe experiment to develop a sound criterion for failure of internally wall thinned pipe subjected to combined pressure and bending loads. By comparing the predictions of failure to actual failure load and displacement, an appropriate criterion was investigated. From this investigation, it is concluded that true ultimate stress criterion is the most accurate to predict failure of wall thinned pipe under combined loads, but it is not conservative under some conditions. Engineering ultimate stress estimates the failure load and displacement reasonably for al conditions, although the predictions are less accurate compared with the results predicted by true ultimate stress criterion.

• 한국농공학회지
• /
• 제40권4호
• /
• pp.109-119
• /
• 1998

Recently pipe-framed greenhouses are widely constructed on domestic farm area. These greenhouses are extremely light-weighted structures and so are easily damaged under strong wind due to the lack of uplift resistance of foundation piles. This experiment was carried out by laboratory soil tank to investigate the displacement be haviors of cylindrical pile foundations according to the uplift loads. Tested soils were sampled from two different greenhouse areas. The treatment for each soil type are consisted of 3 different soil moisture conditions, 2 different soil depths, and 3 different soil compaction ratios. Each test was designed to be repeated 2 times and additional tests were carried out when needed. The results are summarized as follows : 1. When the soil moisture content are low and/or pile foundations are buried relatively shallow, ultimate uplift capacity of foundation soil was generated just after begining of uplift displacement. But under the high moisture conditions and/or deeply buried depth, ultimate up-lift capacity of foundation soil was generated before the begining of uplift displacement. 2. For the case of soil S$_1$, the ultimate uplift capacity of piles depending on moisture contents was found to be highest in optimum moisture condition and in the order of air dryed and saturated moisture contents. But for the case of soil S$_2$, the ultimate uplift capacity was found to be highest in optimum moisture condition and in the order of saturated and air dryed moisture contents. 3. Ultimate uplift capacities are varied depending on the pile foundation soil moisture conditions. Under the conditions of optimum soil moisture contents with 60cm soil depth, the ultimate uplift capacity of pile foundation in compaction ratio of 80%, 85%, and 90% for soil 51 are 76kg, 115kg, and 155kg, respectively, and for soil S$_2$are 36kg, 60kg, and 92kg, respectively. But considering that typical greenhouse uplift failure be occurred under saturnted soil moisture content which prevails during high wind storm accompanying heavy rain, pile foundation is required to be designed under the soil condition of saturated moisture content. 4. Approximated safe wind velosities estimated for soil sample S$_1$and S$_2$are 32.92m/s and 26.58m/s respectively under the optimum soil condition of 90% compaction ratio and optimum moisture content. But considering the uplift failure pattern under saturated moisture contents which are typical situations of high wind accompanying heavy rain, the safe wind velosities for soil sample S$_1$and S$_2$are not any higher than 20.33m/s and 22.69m/s respectively.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.93-96
• /
• 2005

Since the columns with flexure-shear failure have lower ductility than those with flexural failure, shear capacity curve models shall be applied as well as flexural capacity curve in order to determine ultimate displacement for seismic design or performance evaluation. In this paper, a modified shear capacity curve model is proposed and compared with the other models such as the CALTRANS model, Aschheim et al.'s model, and Priestley et al.'s model. Four shear capacity curve models are applied to the 4 full scale circular bridge column test results and the accuracy of each model is discussed. It may not be fully adequate to drive a final decision from the application to the limited number of test results, however the proposed model provides the better prediction of failure mode and ultimate displacement than the other models for the selected column test results.