• Journal of Mechanical Science and Technology
• /
• v.20 no.11
• /
• pp.1942-1949
• /
• 2006

Typically, condensate forms as droplets on the fin surfaces and may bridge the space between the fin surfaces. This is due to the dry characteristics inherent to the fin surface. The droplets increase the air-side pressure drop. In the case of high air velocities, these droplets may be blown off the fins and entrained in the air stream. To minimize the formation of condensate droplet, the wet ability of the fins must be improved. The carry-over velocity is affected by fin surface characteristics. To avoid carry-over in the air conditioner having the highest air velocity of 1.5 m/sec, the dynamic contact angle (DCA) should be at least lowly under $60^{\circ}$.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.9
• /
• pp.1149-1156
• /
• 2001

The objective of the present study is to investigate the performance of electronic scale mitigation unit(ESMU), which reduces the amount of scale in a heat exchanger. The circular tube with diameter of 19mm and plate-and-frame heat exchangers with 20 thermal plates were used for the tests. In order to accelerate the rate of scale in a laboratory test, artificial hard water of 1000ppm(as CaCO$_3$) was recirculated at a flow rate of 5 lpm, 7 lpm, and 9 lpm throughout the tests. The effect of ESMU on the scale thickness and overall heat transfer coefficients was examined. The test results showed that the ESMU could reduce the scale deposits even in the acceleated test.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.9
• /
• pp.801-804
• /
• 2000

High-temperature superconductor of Bi-2212 system was fabricated by CFP(Centrifugal Forming Process). To make a uniform specimen slurry was prepared in the ratio of 7:3(powder : binder) and ball milled for 24 hours. Milled slurry was charged into a rotating mold with 450 rpm and dried at room temperature. Then the specimen was performed binder burn-out at 35$0^{\circ}C$ and heated for partial melting to 86$0^{\circ}C$. XRD analysis of most specimens were shown 2212 phase and observed a local plate shped microstructure with a well aligned c-axis direction from SEM images. Measured T$_{c}$(Critical temperature) was about 64 K.K.

• Microbiology and Biotechnology Letters
• /
• v.21 no.3
• /
• pp.263-268
• /
• 1993

Seventeen strains were isolated from soil, cattle rumen, cereal sewage dregs, insect on agar plate containing insoluble glucan as a sole carbon source from immobilized Streptococcus mutans, which produced alpha-1,3 glucanase for lysis of dental plaque. Among these strains isolated from soil, SW-522 and SW-713 that had appeared to produce the high level of alpha-1,3 glucanase, degraded insoluble glucan from S. mutans 97.6% and 49.4%, respectively in 5 hours. The activity of crude alpha-1,3 glucanase from SW-522 was 1.3mg insoluble glucan/min.mg protein. This enzyme was entirely degraded insoluble glucan on glass tube which produced by S. mutans in TH medium with 5% sucrose.

• YAKHAK HOEJI
• /
• v.11 no.1_2
• /
• pp.4-6
• /
• 1967

Cation exchange resin particles amberlite IRC-50 were used as a medium for a identific test of alkaloids with dragendorff reagent. The procedures were as follows; A few particles of amberlite IRC-50 were added to the small portion of sample solutions on a spot plate or in a test tube. After 20 minutes-an hour, a drop of dragendorff reagent were added to particles of resin that were adsorbed. When alkaloid was present, the original color of the resin particles changed instantly to red or reddish orange depending on the amount and kind of alkaloid, while in the absence of alkaloid the original color of the resin particles changed light yellow. These methods were more sensitive than the ordinary spot test or paper spot test for alkaloid. The limits of identifications of nine alkaloids were tested by these methods and compared with the paper spot test method.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1991.04a
• /
• pp.251-255
• /
• 1991

The primary objectives of the rolling process are to reduce the cross section of the incoming material while improving its properties and to obtain the desired section at the exit from the rolls. Many engineering metals, suchas aluminium alloys, copper alloys, and steels are often cast intoingots and are then further processed byhot rolling into blooms, slabs, and billets, which are subsequently rolled into other products such as plate, sheet, tube, rod, bar, and structural shapes. In shape rolling a round or square bar is rolled in several passes into various shapes. During eachpass, the bar elongates as well as spreads. Thus, a very complex three-dimensional metal flow takes place. In this paper TASKS results for the simulation of a 7 pass square-to-round shape rolling are presented. The results are verified by comparing it with experimental results from a previous study conducted at the Battelle Columbus Labs

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.4
• /
• pp.383-390
• /
• 2001

Long-range guided wave inspection is a new emerging technology for rapidly and globally inspecting a large area of a structure from a single test location. This paper describes a general overview of the guided wave properties and its application for long-range inspection of structures the principle and instrument system for a guided wave inspection technology called "magnetostrictive sensor (MsS)" that generates and detects guided waves electromagnetically in the material under testing, and examples of long-range guided wave inspection of structures that can be accomplished using the MsS.

• Journal of the Korean Ceramic Society
• /
• v.25 no.2
• /
• pp.95-100
• /
• 1988

Single crystals of sapphire were grown from solution by slow cooling method using B2O3 and PbO as flux agents. The morphology of grown crystals was tube, rhombohedral, or hexagonal-plate. It was found that the morphology and the size of grown crystal were highly dependent on the amount of fluxes in the solution, the ratio of B2O3 vs. PbO, and cooling rate.

• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.9-16
• /
• 2007

This study aims to suggest an evaluation method of thermal environment using CFD, not an experiment, which is usual in the field. Model train is the newly introduced Mugunghwa train. Since its compartment occupies a large space and chairs and other accessories make it a complicated structure, 3-D calculation might take too much time and effort to make evaluation itself possible. Therefore, we suggest a 2-D model to replace the original 3-D model for averaged temperature and temperature distribution in the cabin.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.347-354
• /
• 2002

In this paper, when structures are constructed in the soft ground with poor bearing capacity at Incheon International Airport(railroad area), as for the grouting columns built In soft ground by high pressure jet grouting with Triple tube rod(super injection grouting), the effects on reinforcement and bearing capacity of ground are investigated. A unconfined compressive strength tests has been performed on the specimens sampled from the grouting columns and a mass plate bearing test has been performed on a grouting column. The test results show that super injection grouting has a sufficient effect on composite ground improved of foundation ground and reatraint of settlement of structure.