• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.1
• /
• pp.145-151
• /
• 1998

This paper addresses the results of an experimental and analytical research of cylindrical coil spring subjected to dynamic behavior. Transfer functions are presented for both deflection and transmitted force as the output with force as the input. Steady state sinusoidal magnitude ratio and transmittance are plotted along with experimental data. It is shown that dynamic characteristic of cylindrical coil spring must be used to enhance the reability of vibration system dynamic behavior analysis in actuating over some frequency.

• Transactions on Electrical and Electronic Materials
• /
• v.13 no.5
• /
• pp.241-244
• /
• 2012

Antimony doped tin oxide (ATO) thin films on glass substrate were prepared by the chemical solution deposition (CSD) method, using sol-gel solution synthesized by non-alkoxide precursors and the sol-gel route. The crystallinity and electrical properties of ATO thin films were investigated as a function of the annealing condition (both annealing environments and temperatures), and antimony (Sb) doping concentration. Electrical resistivity, carrier concentration, Hall mobility and optical transmittance of ATO thin films were improved by Sb doping up to 5~8 mol% and annealing in a low vacuum atmosphere, compared to the undoped tin oxide counterpart. 5 mol% Sb doped ATO film annealed at $550^{\circ}C$ in a low vacuum atmosphere showed the highest electrical properties, with electrical resistivity of about $8{\sim}10{\times}10^{-3}{\Omega}{\cdot}cm$, and optical transmittance of ~85% in the visible range. Our research demonstrates the feasibility of low-cost solution-processed transparent conductive oxide thin films, by controlling the appropriate doping concentration and annealing conditions.

• Journal of the Korean Vacuum Society
• /
• v.10 no.2
• /
• pp.194-200
• /
• 2001

In this study, the optical properties of diamond-like carbon(DLC) films, which was synthesized by 13.56 MHz rf plasma enhanced chemical vapor deposition system(PECVD), were investigated. We observed the variation of the transmittance and optical band gap with respect to deposition condition. The change of the transmittance and optical band gap of the DLC films were investigated as a function of RF power, working pressure, and additional gas. The optical band gap decreased with the increase of RF power and working pressure. We could verify the bond structures change of DLC films by observing the content of hydrogen using FT-IR spectroscopy. And the addition of hydrogen and nitrogen decreased the optical band gap by the breakage of C-H bond of DLC films during the deposition.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.4
• /
• pp.146-154
• /
• 2008

This study was carried out for the purpose of obtaining the basic data for color identification of amethyst by spectrophotometer. For this, the eleven amethyst stone and one citrine stone from eight countries were prepared in facet cut or plate. The transmittance and reflection of this samples were investigated as a function of wavelength. The transmittance or reflection was transformed to tristimulus value (X, Y, Z) and chromaticity value (x, y, z) and then compared with the results of eye observation which was plotted on cm xyY color space. Finally, the influence of the amethyst's thickness on transmittance or reflection was investigated.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.333-336
• /
• 2008

We have studied on optical properties of advanced S-IPS with a fine pitch electrode and a new finger design. Transmittance of panel increases with decreasing of width and angle of finger electrode. In order to improve transmittance, fine pitch electrode of ${\sim}2{\mu}m$ and rubbing angle of 10 degree have been adopted. Various optical performances are defined as the function of finger design and field intensify across the IPS pixel electrodes. We have developed the advanced electrode structures with a high performance. As a result, the optical properties of 42" full HD with 120Hz frequency shows high transmittance over 5%, contrast ratio of 1800:1, gray-to-gray response time of 4.4ms, respectively. And also we have studied that the moving picture quality of IPS LCD is related with design parameters of IPS cells and finger shape.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1477-1479
• /
• 2005

In this work, the ITO thin films were prepared by FTS (Facing Targets Sputtering) system under different sputtering conditions which were varying $O_2$ gas flow, input current at room temperature. As a function of sputtering conditions, electrical and optical properties of prepared ITO thin films were measured. The electrical, optical characteristics and surface roughness of prepared ITO thin films were measured. In the results, as increasing $O_2$ gas 0.1[sccm] to 0.7[sccm], resistivity of ITO thin film was increased with a decreasing carrier concentration, $O_2$ gas over 0.3[sccm] the carrier mobility have a similarly value. Transmittance of prepared ITO thin films were improved at increasing $O_2$ gas 0.1[sccm] to 0.7[sccm]. And transmittance of all of the prepared ITO thin films was over 80%. We could obtain resistivity $6.19{\times}10^{-4}[{\omega}{\cdot}cm]$, carrier mobility $22.9[cm^2/V{\cdot}sec]$, carrier concentration $4.41{\times}10^{20}[cm^{-3}]$ and transmittance over 80% of ITO thin film prepared at working pressure 1mTorr, input current 0.4A without any substrate heating.

• Applied Chemistry for Engineering
• /
• v.1 no.2
• /
• pp.161-167
• /
• 1990

Polymethylphenylsilane(PMPS) was synthesized with methylphenyldichlorosilane using metal sodium. Various sample coated on quartz plate were exposed and the yield of residual film was calculated. To obtain the fine image forming after developing and drying, optical transmittance characterization have to be considered. Exposure is described by three optical parameters X, Y, and Z. There parameters are normally determined from optical transmittance measurements of exposed PMPS films. Z parameter was determined from the initial slope of a transmittance according to exposure time. This set of function parameters provided a complete description of photoresist exposure and development and became the basis for the theoretical process models.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.6
• /
• pp.471-474
• /
• 2020

In recent years, the challenge of higher energy efficiency has emerged as urban buildings have become taller, and the area of window glasses has increased. To address the problem of energy efficiency in buildings, research on smart windows is being actively conducted. In this study, an accelerated experiment for thermal stability was conducted to fabricate a liquid crystal cell applicable to external windows. It was confirmed from the study that the function is maintained even in a high-temperature external environment through the change in transmittance by voltage. Compared with the initial transmittance, after the passage of time, the smart window cell to which the sealant was applied showed a small change in transmittance of 1~2%. This result confirmed the thermal stability of the liquid crystal-based smart window.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.3
• /
• pp.121-125
• /
• 2015

We studied the blue fluorescent OLED with Mg:Ag, Al, Ni as anode materials. Blue fluorescent OLEDs were fabricated using Anode / $MoO_3$ (3 nm) / 2-TNATA (60 nm) / NPB (30 nm) / SH-1 : BD-2 (5 vol.%, 30 nm) / Bphen (40 nm) / Liq (1 nm) / Al (150 nm). Current density of OLED with Mg:Ag was not measured due to too low work function, and that of OLED with Al showed $45.2mA/cm^2$ at 12 V. Luminance and Current efficiency of OLED with Al showed $385.1cd/m^2$ and 0.9 cd/A. Current density of OLED with Ni of 8, 10, 12 nm thickness showed 10, 12.9, $37.2mA/cm^2$, respectively. Luminance and Current efficiency of OLED with Ni of 8, 10, 12 nm thickness showed 670.9, 991.2, $1,320cd/m^2$ and 6.7, 7.7, 3.6 cd/A, respectively. Transmittance of Al was 52.2% at 476 nm wavelength and that of Ni of 8, 10, 12 nm thickness was 79, 77, 74 %, respectively. In spite of best current density, OLED with Al showed the lowest luminance and current efficiency because of low work function and poor transmittance. When thickness of Ni was increased to 12nm, current efficiency was sharply lower owing to bad transmittance and unbalance of holes and electrons. Finally, OLED with Ni of 10 nm thicknes showed the highest current efficiency.

• Journal of the Semiconductor & Display Technology
• /
• v.3 no.4
• /
• pp.5-11
• /
• 2004

Optical properties of PET(Polyethylene terephthalate), PC(Polycarbonate), Acrylic resin and PE(Polyethylene) sheets were studied as a function of heat treating temperature of $60^{\circ}C$ to $150^{\circ}C$. By the heat treatment, optical properties of transmittance, absorbance, and reflectance showed a considerable change with different ways according to the materials. To understand the reason of optical property change, X-ray diffraction and surface morphology were also investigated. It was observed that small crystallite and pore that can cause scattering largely affect the transmittance. It was suggested that change of surface chemical bond induce the reflectance variation.