• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1678-1681
• /
• 2004

The light-transmission technique has been applied to a slit rheometer for measuring red blood cell aggregation as well as blood viscosity over a range of shear rates. For measurement of blood viscosity and aggregation, instantaneous pressure and transmit-light intensity are measured with time. Using a precision pressure measurement, one can determine the shear stress and shear rate. In addition, a transmitted light through a blood sample indicates degree of RBC aggregation. With abruptly flowing with high shear rate, RBCs rapidly disaggregate and the intensity of the transmitted light becomes low. When continuously flowing with decreasing shear rate, RBCs tend to re-aggregate and the corresponding transmit-intensity gradually increases with time. The light intensity as a degree of RBC aggregation is plotted against shear rate and compared with blood viscosity. The advantages of this design are dual measurement at a time, simplicity, i.e., ease of operation and no moving parts, low cost, short operating time, and the disposable kit which is contacted with blood sample.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.1
• /
• pp.20-23
• /
• 2004

In this paper, the emission properties of electrodeless fluorescent lamp were discussed using the inductively coupled plasma. To transmit the electromagnetic energy into the chamber, a RF power of 13.56 [MHz] was applied to the antenna and considering the Ar gas pressure and the RF electric power change, the emission spectrum, Ar I line, luminance were investigated. At this time, the input parameter for ICP RF plasma, Ar gas pressure and RF power were applied in the range of 10∼60 [mTorr], 10∼300 [W], respectively. From emission intensity and lumnance intensity results, the mode transition from E-mode to H-mode was observed. This implies that this method can be used to find an optimal RF power for efficient light illumination in an electrodeless fluorescent lamp.

• Korean Journal of Microbiology
• /
• v.20 no.1
• /
• pp.21-26
• /
• 1982

The disinfection effects of sunlight and predacious microorganisms on enteria of Escherichia coli and Proteus vulgaris were examined in sewage water at 22 to $26^{\circ}C$. The test prganisms were disinfected by 4 to 5 logs during 6-hour a day exposure to sunlight for seven days. The effect was proportional to the light intensity and was proved to be dur to the action of the visible light of short wavelength which can transmit the soft glass of a flask glass. The predacious microorganisms decreased trhe test organisms by about 3 to 4 logs during 7 days. The complex actions of sunlight and predacious microorganisms were variable depending upon the test organisms, but the total effects of those enviromental factors were yet completely understood.

• Journal of Environmental Science International
• /
• v.28 no.5
• /
• pp.521-526
• /
• 2019

In this study, a solar light collector that collects and transmits solar light required for crop production in a closed plant production system was developed. The solar light collector consisted of a Fresnel lens for collecting solar light, and a tracking actuator for tracking solar light from sunrise to sunset to increase the light collection efficiency. The optical fiber that transmitted solar light was made of Glass Optical Fiber (GOF), and it had an excellent optical transmission rate. After collecting the solar light, the amount of light was measured at 5, 10, 15, 20, 25, and 30 cm distances from the GOF through the darkroom by using a light sensor logger connected to a quantum and pyranometer sensor. Compared with solar light, the light intensity of pyranometer sensor measured at 5 cm was 114% higher than solar light, and 61% at 10 cm. In addition, it was observed that it is possible to transmit the necessary amount of light for growing crops up to about 15 cm (as over 22%) through GOF. Therefore, adding diffusers to the solar light collector should be expected to replace artificial light in plant factories or plug seedlings nurseries for leafy vegetables. More studies on the solar light collection devices and the light transmission devices that have high light collection efficiency should be conducted.

• Clean Technology
• /
• v.6 no.1
• /
• pp.71-78
• /
• 2000

Removal rates of hydrogen sulfide were investigated to known effects of several light sources with external and internal irradiation on the desulfurization using C. thiosulfatophilum. In the case of internal illumination system, optical-fiber photobioreactor was applied to increase the light availability. Furthermore, sunlight was used as the main light energy in the daytime and metal-halide lamp was applied as an additional light energy at night. Light energy of 99% was saved by the application of the LED's array in comparison with the incandescent light source. $H_2S$ removal rates at 5,000 lux in a 4-L photobioreactor were shown as 0.040, 0.138, 0.136, and 0.134 (${\mu}mol$ $H_2S/min$)/(mg protein/L), respectively, in the following order of light sources, when several light sources such as fluorescent, energy-saving, incandescent, halogen lamp, and filtered light at 460 nm were applied. Removal rate per unit cell concentration with the internal light diffused optical-fibers increased about 1 six times as much as that with the external light sources. Removal rate per unit cell concentration, using sunlight in the daytime and a metal-halide lamp at night, was 0.41 less than 0.869 (${\mu}mol$ $H_2S/min$)/(mg protein/L) using a 400 W metal-halide lamp day and night, since the automatic sunlight collection system can transmit the light intensity as only 10% of that with a metal-halide lamp.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.10a
• /
• pp.480-483
• /
• 2018

In this paper, we study the interference canceling and image sensing processing technology of multiple light sources for high speed transmission in CMOS sensor based visible light communication system. To improve transmission capacity in optical camera communications via image sensors, different data must be transmitted simultaneously from each LED. However, multiple LED light source environments for high-speed transmission can cause interference between adjacent LEDs. In this case, since the visible light communication system generally uses intensity modulation, when a plurality of LEDs transmit data at the same time, it is difficult to accurately detect the respective LEDs due to the light scattering interference of the adjacent LEDs. In order to solve this problem, the ON / OFF state of many LEDs of the light source is accurately recognized by using a dual CMOS sensor, and the spectral estimation technique and the pixel image signal processing technique of each LED are proposed. This technique can accurately recognize multiple LED pixels and improve the total average bit error rate and throughput of a MISO-VLC system.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.1
• /
• pp.123-128
• /
• 2017

In this paper, we have proposed and implemented a smart sensor network system based on the Arduino open source hardware. The proposed smart sensor network system is composed of kinds of sensors and open-source hardware based, Arduino, etc. that can handle the measured sensor values. Also the communication modules that can be used to transmit the measured sensor values from the sensor control unit are configured. In the control unit the sensor data such as temperature, humidity, light intensity can be transmit to the main program and the main program will save the data in the DB or transmitting the value of the particular control signal to the control device or the actuator. The user can also check the information in the system using the measured values from the smart sensor networks through the web, or to remotely control a variety of actuators. And it is possible to manage a smart autonomous control over whether and how the proposed system.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.52 no.3
• /
• pp.183-190
• /
• 2016

This study carried out an experiment to find out the reaction of hairtail, Trichinus lepturus to the colors of LED light as a basic study on the development of the trolling gear and a method to enable the day-night operation. We used hairtails caught around Seongsan-po, Jeju Island by set nets and hairtail angling. The seven hairtails of the average length 68.9 cm (SD 9.2 cm) and the average weight 135.9 g (SD 47.9 g) were adapted themselves in the experimental water tank, 15 m Self-Governing 1.7 m in height and 1.5 m in depth, and then they were studied. We conducted experiment at the Ocean and Fisheries Research Institute in Jeju Special Self-Governing Province, from November to December 2015, and the sea surface temperature was between 16.5 and $19.5^{\circ}C$. The four colors of LED light, blue, white, green and red, were set up to transmit downward from the marginal area of tank. The 1 meter depth light intensity of LED colors is as follows: $0.09w/m^2/s$ (blue), $0.18w/m^2/s$ (white), $0.04w/m^2/s$ (green) and $0.007w/m^2/s$(red) To know the optimum LED color light, we selected one with better reaction rate after comparison of two colors simultaneously and the selected color was again compared to the other color in a tournament style two times a day (day and night) and ten times totally. The reaction rates were shown as the frequencies of hairtail appearance for 5 minutes in the lighting zone after turning on the LED lights. The reaction rate of the blue was at 97% unlike the red 3% (p < 0.001). The blue was at 75% unlike the green at 25% (p < 0.001). The blue was at 67% unlike the white at 33% (p < 0.001). Therefore, the color of light source showing the highest reaction rate was the blue.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.31.1-31.1
• /
• 2009

Carbon nanotubes (CNTs) are attractive material because of their superior electrical, mechanical, and chemical properties. Furthermore, their geometric features such as a large aspect ratio and a small radius of curvature at tip make them ideal for low-voltage field emission devices including backlight units of liquid crystal display, lighting lamps, X-ray source, microwave amplifiers, electron microscopes, etc. In field emission devices for display applications, the phosphor anode is positioned against the CNT emitters. In most case, light generated from the phosphor by electron bombardment passes through the anode front plate to reach observers. However, light is produced in a narrow depth of the surface of the phosphor layer because phosphor particles are big as much as several micrometers, which means that it is necessary to transmit through the phosphor layer. Hence, a drop of light intensity is unavoidable during this process. In this study, we fabricated a transparent cathode back plate by depositing an ultra-thin film of single walled CNTs (SWCNTs) on an indium tin oxide (ITO)-coated glass substrate. Two types of phosphor anode plates were employed to our transparent cathode back plate: One is an ITO glass substrate with a phosphor layer and the other is a Cr-coated glass substrate with phosphor layer. For the former case, light was radiated from both the front and the back sides, where luminance on the back was ~30% higher than that on the front in our experiments. For the other case, however, light was emitted only from the cathode back side as the Cr layer on the anode glass rolled as a reflecting mirror, improving the light luminance as much as ~60% compared with that on the front of one. This study seems to be discussed about the morphologies and field emission characteristics of CNT emitters according to the experimental parameters in fabricating the lamps emitting light on the both sides or only on the cathode back side. The experimental procedures are as follows. First, a CNT aqueous solution was prepared by ultrasonically dispersing purified SWCNTs in deionized water with sodium dodecyl sulfate (SDS). A milliliter or even several tens of micro-liters of CNT solution was deposited onto a porous alumina membrane through vacuum filtration. Thereafter, the alumina membrane was solvated with the 3 M NaOH solution and the floating CNT film was easily transferred to an ITO glass substrate. It is required for CNT film to make standing CNTs up to serve as electron emitter through an adhesive roller activation.

• Journal of the Mineralogical Society of Korea
• /
• v.22 no.4
• /
• pp.407-415
• /
• 2009

The change of the nitrogen-related centers and the color change of electron beam irradiated type Ia natural diamonds were studied. The irradiation of diamond with high-energy electron beam creates lattice defects which are neutral single vacancy $V^0$. It increased with increasing electron dose density. The B aggregation seems to produce vacancies more easily than the A aggregation, because diamonds with more B aggregation have more platelets, which are sufficient breakable size by electron beam. Greenish blue color of irradiated diamond is changed to darker with increasing electron dose density. GR1 centers with a zero-phonon line at 741 nm and phonon sidebands make transmit visible light at 530 nm and it moves to 500 nm with higher intensity of GR1 centers.