• ETRI Journal
• /
• v.34 no.3
• /
• pp.352-360
• /
• 2012

This paper proposes a low-cost, low-power, and high-capacity optical-electrical-optical-type reach extender that can provide 3R frame regeneration and remote management to increase the reach and split ratio with no change to a legacy time division multiple access passive optical network. To provide remote management, the extender gathers information regarding optical transceivers and link status per port and then transmits to a service provider using a simple network management protocol agent. The extender can also apply to an Ethernet passive optical network (E-PON) or a gigabit-capable PON (G-PON) by remote control. In a G-PON, in particular, it can provide burst mode signal retiming and burst-to-continuous mode conversion at the upstream path through a G-PON transmission convergence frame adaptor. Our proposed reach extender is based on the quad-port architecture for cost-effective design and can accommodate both the physical reach of 60 km and the 512 split ratios in a G-PON and the physical reach of 80 km and the 256 split ratios in an E-PON.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.11
• /
• pp.26-32
• /
• 2014

Single-Carrier Frequency division multiplexing (SC-FDM) has been selected for the uplink transmission technique in 3GPP-LTE since it has an advantage of low peak-to-average power ratio (PAPR) in user's perspective. The receiver typically uses a frequency domain equalizer, which, however, suffers from noise boost and/or residual ISI especially when the channel has deep nulls. In this paper, we propose using turbo equalizer to mitigate such a problem. We provide link level performance comparison and an insight into how many iteration is needed for reasonable performance and complexity.

• Corrosion Science and Technology
• /
• v.19 no.3
• /
• pp.146-155
• /
• 2020

To elucidate the effect of heat inputs on phase transformation and resistance to intergranular corrosion of F316 austenitic stainless steel (ASS), thermodynamic calculations of each phase and time-temperature-transformation diagram were conducted using JMaPro simulation software, oxalic acid etch test, double-loop electrochemical potentiokinetic reactivation test (DL-EPR), field emission scanning electron microscopy with energy dispersive spectroscopy, and transmission electron microscopy analyses of Cr carbide (Cr₂₃C₆), austenite phase and ferrite phase. F316 ASS containing a relatively low C content of 0.043 wt% showed a slightly sensitized microstructure (acceptably dual structure) due to a small amount of Cr carbide precipitated at heat affected zone irrespective of heat inputs. Based on results of DL-EPR test, although heat input was increased, the ratio of I_r to I_a was only increased very slightly due to a slight sensitization. Therefore, heat inputs have little influences on resistance to intergranular corrosion of F316 austenitic stainless steel containing 0.043 wt% C.

• Advances in materials Research
• /
• v.4 no.4
• /
• pp.193-205
• /
• 2015

Contamination by bacterial strands is a major problem after bone replacement surgeries, so there is a great need to develop low cost biocompatible antibacterial bioactive scaffolds to be used in bone tissue engineering. For this purpose, nano-zinc doped hydroxyapatite with different zinc-concentrations (5, 10 and 15 mol%) was successfully prepared by the wet chemical precipitation method. The prepared powders were used to form porous scaffolds containing biodegradable Ca-cross-linked alginate (5%) in order to enhance the properties of alginate scaffolds. The scaffolds were prepared using the freeze-gelation method. The prepared powders were tested by X-ray diffraction; transmission electron microscope and Fourier transform infrared analyses, while the prepared scaffolds were investigated by Fourier transform infrared analyses, thermogravimetric analyses and measurement of the antibacterial properties. Best results were obtained from scaffold containing 15% mol zinc-doped hydroxyapatite powders and 5% alginate concentration with ratio of 70:30.

• Steel and Composite Structures
• /
• v.20 no.2
• /
• pp.431-445
• /
• 2016

Seismic behavior of new composite structural system with a fabricated floor was studied. A two-bay and three-story structural model with the scale ratio of 1/4 was consequently designed. Based on the proposed model, multiple factors including energy dissipation capacity, stiffness degradation and deformation performance were analyzed through equivalent single degree of freedom pseudo-dynamic test with different earthquake levels. The results show that, structural integrity as well as the effective transmission of the horizontal force can be ensured by additional X bracing at the bottom of the rigidity of the floor without concrete topping. It is proved that the cast-in-place floor in areas with high seismic intensity can be replaced by the prefabricated floor without pouring surface layer. The results provide a reliable theoretical basis for the seismic design of the similar structural systems in engineering application.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.20.2-20.2
• /
• 2009

최근 무전해 식각법을 이용한 실리콘 나노와이어 합성이 다양한 각도에서 이루어지고 있다. 무전해 식각법을 통한 나노와이어 합성은, 단결정 실리콘 기판에 촉매를 올려 기판을 식각할 수 있는데, 이 방법을 이용하여 넓은 면적의 수직방향으로 배열된 10 ~ 300nm 지름의 단결정 실리콘 나노와이어를 합성할 수 있다. 본 연구에서는 무전해 식각법으로 boron이 도핑된 p-type실리콘 기판을 식각하여 실리콘 나노와이어를 합성하였고, 단일 나노와이어의 field-effect transistor(FET) 소자가 가지는 전기적 특성에 대하여 분석하였다. 특히 무전해 식각법을 이용하여 나노와이어를 합성할 때, 촉매로 사용되는 Ag particle이 나노와이어에 미치는 영향에 대해서 분석해 보았다. FET 소자의 게이트 절연막은 가장 일반적으로 사용되는 SiO2 (300nm)와 고유전체로 잘 알려진HfO2(80nm)를 사용하여 전기적 특성을 비교하여 보았다. 한편, HfO2 박막은 atomiclayer deposition(ALD)장비를 이용하여 증착하였다. 합성된 실리콘 나노와이어의 경우 X-ray diffraction(XRD)로 결정성을 확인하였으며, high-resolution transmission electron microscopy(HRTEM)으로 결정성 및 나노와이어의 표면 형태를 확인하였다. 전기적 특성은 I-V 측정을 통하여 Ion/Ioff ratio, 이동도, subthreshold swing, subthreshold voltage값을 평가하였다.

• Journal of Communications and Networks
• /
• v.18 no.3
• /
• pp.420-428
• /
• 2016

In this paper, we investigate the scheduling and power allocation for coordinated multi-point transmission in downlink long term evolution advanced (LTE-A) systems, where orthogonal frequency division multiple-access is used. The proposed scheme jointly optimizes user selection, power allocation, and modulation and coding scheme (MCS) selection to maximize the weighted sum throughput with fairness consideration. Considering practical constraints in LTE-A systems, the MCSs for the resource blocks assigned to the same user need to be the same. Since the optimization problem is a combinatorial and non-convex one with high complexity, a low-complexity algorithm is proposed by separating the user selection and power allocation into two subproblems. To further simplify the optimization problem for power allocation, the instantaneous signal-to-interference-plus-noise ratio (SINR) and the average SINR are adopted to allocate power in a single cell and multiple coordinated cells, respectively. Simulation results show that the proposed scheme can improve the average system throughput and the cell-edge user throughput significantly compared with the existing schemes with limited feedback.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.3C
• /
• pp.287-294
• /
• 2010

MB-OFDM UWB system will adopt LDPC codes to enhance the decoding performance with higher data rates. In this paper, we will consider algorithm and architecture of the LDPC codes in MB-OFDM UWB system. To suggest the hardware efficient LDPC decoder architecture, LLR(log-likelihood-ration) calculation algorithms and check node update algorithms are analyzed. And we proposed the architecture of LDPC decoder for the high throughput application of Wimedia UWB. We estimated the feasibility of the proposed architecture by implementation in a FPGA. The implementation results show our architecture attains higher throughput than other result of QC-LDPC case. Using this architecture, we can implement LDPC decoder for high throughput transmission, but it is 0.2dB inferior to the BP algorithm.

• Journal of the Korean Institute of Educational Facilities
• /
• v.18 no.5
• /
• pp.3-11
• /
• 2011

In this study, the effect of treating 1-dimensional diffusers on the classroom acoustics was investigated to determine if the diffuser are beneficial for performing the preferred acoustical conditions for speech. A 1/10 scale model of a classroom was used to measure the acoustical parameters, T30, $C_{50}$, STI and SNR in that room. The room acoustical conditions were varied by treating diffusers either on the front or side walls of the classroom. When the diffusers were treated on the side walls around the student's areas, a shorter reverberation time at low frequencies was obtained and resulted in performing uniform reverberation times across the frequency bands. The $C_{50}$ values at mid- and high-frequencies were increased by treating the diffusers either on front or side wall surfaces. The highest STI and SNR values were obtained when the diffuser was treated on the front wall around the teacher's areas. It is found that diffusers are beneficial to increase the intelligibility of speech for the rear seats of the rooms.

• Carbon letters
• /
• v.5 no.3
• /
• pp.133-141
• /
• 2004

The synthetic behaviors of carbon nanotubes (CNTs) by Fe/MgO catalysts were investigated in 0~90 wt.% range of MgO mixture ratios by catalytic chemical vapor deposition (CCVD) process. The CNTs were synthesized with 40 minutes of synthetic time, and 923 K of synthetic temperature using 0.1 L/min of ethylene gas and 1.0 L/min of hydrogen gas as synthetic and carrier gas, respectively. As the increase of synthetic temperatures and times, the diameters of CNTs become thicker. The carbon yield showed in a parabolic curve as MgO content increased and the maximum carbon yield was obtained at 30 wt.% of MgO. There were no obvious changes in the diameters of CNTs respect to the change of MgO content. Fe/MgO CNTs showed good crystalinity by High Resolution Transmission Electron microscope (HR-TEM) analysis. The behaviors of Fe/MgO CNTs have a tendency of depending on synthetic time and temperature rather than MgO content.