• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.231-231
• /
• 2010

Thermoelectric properties of a multi-layered thin film, which was composed with indium selenide and bismuth telluride, were investigated. The structure of the layered thin film is Bi-Te /In-Se/Bi-Te and it was prepared on sapphire substrate by RF magnetron sputter using stoichiometric $Bi_2Te_3$ (99.9%) and $In_2Se_3$(99.99%) target at room temperature. Then, it was annealed at temperature range of 150 - $500^{\circ}C$ in Ar ambient. Structural characterizations were done using X-ray diffraction(XRD, BRUKER, D8, 60kW) and transmission electron microscopy (TEM, FEI, Tecnai, F30 S-Twin), respectively. Cross-section of multi-layer structure was observed by Scanning electron microscopy (SEM). The resistivity and Seebeck coefficient of these samples were also measured by conventional equipment at room temperature. The maximum value of power factor was $1.16\;{\mu}W/k^2m$ at annealing temperature of $400^{\circ}C$.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.5
• /
• pp.130-138
• /
• 2009

6LoWPAN is IPv6 packets transmission technology at Sensor network over the IEEE 802.15.4 Standard MAC and Physical layer. Adaptation layer between IP layer and MAC layer performs fragmentation and reassembly of packet for transmit IPv6 packets. RFC4944, IETF 6LoWPAN WG standard document define packet fragmentation and reassembly. In this paper, we propose the IRM(Immediate Retransmission Method) and SRM(Selective Retransmission Method) to manage packet fragmentation and reassembly at 6LoWPAN. Each time destination receives a fragmented packet, it sends Ack message to the source node on IRM. However, on SRM, the destination node receives all fragmented packet, it sends Ack message or Nak message to the source node. In this case, Nak message include the dropped packet number. To compare the performance of the proposed schemes, we develop a simulator using C++. The result of simulation shows the proposed schemes provider better performance than RFC4944 standard scheme.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.48 no.5
• /
• pp.1-6
• /
• 2011

LED(Light Emitting Diode) components have advantages of longer lifetime, lower power consumption and easy-to-control, compare to normal lamp and fluorescent light, according to the development of recent technologies. Thus, lots of illuminations which utilize LED components could be used. Recently, Visible Light Communication(VLC) which is a part of communication technologies, utilizing high speed response characteristic of LED components, started receiving public attention. In case of VLC, there is no need of frequency allocation due to no use of radio, but also no interference exists during data transmission, much different in ISM((Industrial Scientific Medical band). This is the reason why a lot of research results about VLC are becoming issued. In this paper, a survey of feasibility for using VLC utilizing an original LED illumination for underwater applications has been done and a primitive possibility of its application has been examined.

• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1140-1149
• /
• 2019

In general, there are various pulse width modulation(PWM) methods simply using the offset voltage injection in voltage source converter(VSC). In accordance with the AC side voltage synthesis method with the offset voltage, DC side voltage utilization factor in VSC is changed. Also, this can apply equally to the MMC system. In other words, if the DC side capacity of the high voltage DC(HVDC) transmission system is determined, the maximum reactive power which can be supplied to the AC side can be changed according to the applied output voltage synthesis method with the offset voltage. In this paper, the leg energy pulsation in MMC system according to the AC side output voltage synthesis method with offset voltage which several representative PWM are applied to are mathematically analyzed and compared with each other. Finally, the above results are verified by simulation emulating the 400MVA full-scale MMC system to determine the consistency of the mathematical analysis.

• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1257-1264
• /
• 2019

A 3-GSymbol/s/lane transceiver, which supports the mobile industry processor interface (MIPI) C-physical layer (PHY) specification version 1.1, is proposed. It performs channel mismatch correction to improve the signal integrity that is deteriorated by using three-level signals over three channels. The proposed channel mismatch correction is performed by detecting channel mismatches in the receiver and adjusting the delay times of the transmission data in the transmitter according to the detection result. The channel mismatch detection in the receiver is performed by comparing the phases of the received signals with respect to the pre-determined data pattern transmitted from the transmitter. The proposed MIPI C-PHY receiver is designed using a 65 nm complementary metal-oxide-semiconductor (CMOS) process with 1.2 V supply voltage. The area and power consumption of each transceiver lane are 0.136 ㎟ and 17.4 mW/GSymbol/s, respectively. The proposed channel mismatch correction reduces the time jitter of 88.6 ps caused by the channel mismatch to 34.9 ps.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.4 no.1 s.6
• /
• pp.63-71
• /
• 2005

This paper proposes the channel estimation method robust to severe frequency selective fading channels in O%M system using wide bandwidth for the high data rate transmission. DDCE, which uses data between the high correlated symbols, is usually used for channel estimation in the slow fading channels. DDCE can get high gains in the non-selective channels. As the bandwidth of system gets wider, it becomes more severe frequency selective fading environments so that the reliability of data becomes lower and error flow is occurred. FE method, this paper proposed, uses the relation between sub-carriers of OFDM in frequency selective fading channels so FE method gets some gains by adapting the power value at a target frequency to the mean value of channel estimated values of adjacent sub-carriers. Because FE uses only preamble unlike DDCE using data, it is independent of data rate related to the reliability of data and the number of multipath. Consequently, FE can obtain considerable gains in the wideband systems where the errorflow of DDCE is occurred, and FE is applicable to frequency selective fading environments.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.6
• /
• pp.91-98
• /
• 2004

This paper proposes a PCB plane model for generic SPICE circuit simulators. The proposed model reflects two frequency-dependent losses, namely skin and dielectric losses. After power/ground plane pair is divided into arrays of unit-cells, each unit-cell is modeled using a transmission line and two loss models. The loss model is composed of a resistor for DC loss, series HL ladder circuit for skin loss and series RC ladder circuit for dielectric loss. To verify the validity of the proposed model, it is compared with SPICE ac analysis using frequency-dependent resistors. Also, we show that the estimation results using the proposed model have a good correlation with that of VNA measurement for the typical PCB stack-up structure of general desktop PCs. With the proposed model, not only ac analysis but also transient analysis can be easily done for circuits including various non-linear/linear devices since the model consists of passive elements onl.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.10 s.101
• /
• pp.1043-1049
• /
• 2005

In OFDM system suitable for high capacity high speed broadband transmission, ICI caused by phase noise degrades system performance seriously by destroying the orthogonality among subcarriers. In this paper, a new STFBC method combining ICI self cancellation scheme and antenna, time, frequency diversity is studied to reduce ICI effectively. CPE and ICI are analyzed by the phase noise linear approximation method in the proposed STFBC OFDM system. CIR, PICR and BER are discussed to compare the system performance degraded by phase noise of PLL. As results, STFBC method significantly reduces ICI. Furthermore, the SCI that usually happens in the traditional STBC, SFBC diversity coding method can be easily avoided.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.6
• /
• pp.752-755
• /
• 2012

In this paper, the rectangular spiral shaped antenna is designed and fabricated for 433 MHz TPMS. Proposed antenna has the -10 dB impedance bandwidth of 23 MHz(427~450 MHz). The antenna is fabricated with the size of $5mm(W){\times}23mm(D){\times}10mm(H)$ by brass material. Return loss is below -10 dB at 433 MHz${\pm}$10 MHz mounted tire wheel and not mounted both. The radiation power is -44.21 dBm without wheel and -50.0 dBm installed wheel. The proposed antenna can be practical use through data transmission test results.

• Physical Therapy Korea
• /
• v.10 no.2
• /
• pp.71-84
• /
• 2003

The purpose of this study was to provide information on driving characteristics in persons with spinal cord injury through basic statistic analysis of the survey results. The survey was administered to 44 drivers with spinal cord injury. The subjects' general, neurologic and driving characteristics were analyzed, as well as the degree of difficulty in using their vehicles between tetraplegia and paraplegia. The results were as follows: thirty-five (79.6%) of forty-four respondents was men. The average age was 35.0 years old and the age at the time of injury was 29.0 years old. Their neurologic characteristics were tetraplegics 12 (27.3%) and paraplegics 32 (72.2%). Among complete lesions, the highest level those who could drive independently was C7. All the vehicles were equipped with special devices, including "power steering", "automatic transmission" and "hand controls". The vehicles for cervical cord injury were equipped with "grip bars" as well as for the degree of difficulty in using their vehicles, all the subjects felt that "moving the wheelchair in and out of their vehicles" was too difficult for them to do. We suggest that the driver training should be an essential part of the rehabilitation program for patients with spinal cord injuries to maximize their mobility in the community. This training seems to be essential in order to modify the standards of the Handicapped Drivers Ability Test and to aid the driver rehabilitation program in the health insurance payment system. Also, the driver rehabilitation training program should include instruction in that moving wheelchairs in and out of vehicles.