• 한국결정성장학회지
• /
• 제3권1호
• /
• pp.31-36
• /
• 1993

FZ법을 이용하여 Tourmaline ($NaFe_3Al_6B_3Si_6O_{27}F_4$) 단결정을 성장하였다. 성장조건으로 회전수 상호 역방향으로 20~30rpm, 성장속도 2~5mm/hr로 조절하였다. 성분 원소 중 전이금속 원소가 존재하여 dopant는 첨가하지 않았다. 원료봉은 $1000~1100^{\circ}C$에서 소결하였고 이 온도보다 고온의 영역에서는 F등의 휘발원소의 휘발로 인해 원료봉을 제작하기가 어려웠다. 성장된 결정은 어두운 색을 띄고 있었고 길이 60~50mm, 직경 5~6mm였다. 결정의 원료에 대하여 XRD 분석을 통하여 Tourmaline 조성을 확인하였고 FTIR로 성분의 결합상을 보았다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권4호
• /
• pp.410-416
• /
• 2007

PRAM (Phase change random access memory) is one of the most promising candidates for next generation non-volatile memories. However, the high reset current is one major obstacle to develop a high density PRAM. One way of the reset current reduction is to change the heater electrode material. In this paper, to reduce the reset current for phase transition, we have investigated the effect of heater electrode material parameters using finite element analysis. From the simulation. the reset current of PRAM cell is reduced from 2.0 mA to 0.72 mA as the electrical conductivity of heater is decreased from $1.0{\times}10^6\;(1/{\Omega}{\cdot}m$) to $1.0{\times}10^4\;(1/{\Omega}{\cdot}m$). As the thermal conductivity of heater is decreased, the reset current is slightly reduced. But the reset current of PRAM cell is not changed as the specific heat of heater is changed.

• Computers and Concrete
• /
• 제15권4호
• /
• pp.485-501
• /
• 2015

Cooling by the flow of water through an embedded cooling pipe has become a common and effective artificial thermal control measure for massive concrete structures. However, an extreme thermal gradient induces significant thermal stress, resulting in thermal cracking. Using a mesoscopic finite-element (FE) mesh, three-phase composites of concrete namely aggregate, mortar matrix and interfacial transition zone (ITZ) are modeled. An equivalent probabilistic model is presented for failure study of concrete by assuming that the material properties conform to the Weibull distribution law. Meanwhile, the correlation coefficient introduced by the statistical method is incorporated into the Weibull distribution formula. Subsequently, a series of numerical analyses are used for investigating the influence of the correlation coefficient on tensile strength and the failure process of concrete based on the equivalent probabilistic model. Finally, as an engineering application, damage and failure behavior of concrete cracks induced by a water-cooling pipe are analyzed in-depth by the presented model. Results show that the random distribution of concrete mechanical parameters and the temperature gradient near water-cooling pipe have a significant influence on the pattern and failure progress of temperature-induced micro-cracking in concrete.

• 한국태양에너지학회 논문집
• /
• 제22권4호
• /
• pp.44-50
• /
• 2002

Photosynthesis of plants is effective in the range of 550 to 700 nm of the wavelength of solar irradiation. If the conversion of ultraviolet to the above mentioned region is possible, the photosynthesizing ability is expected to be enhanced. $Eu^{3+}$ doped soda-lime bulk and $TiO_2-SiO_2$ sol-gel coated glasses were prepared and their spectroscopic properties were studied. The absorption and emission spectra for the specimens were measured with the changes of wavelength and Eu ion concentration in the range of the wavelength of 300 to 700nm. The transmittance intensity of visible light through the bulk glass and the coated one was unchanged with the addition of Eu element. The emission spectrum intensity of $Eu^{3+}$ was found to be the maximum at 618 nm which is a transition of $^5DO{\rightarrow}^7F_2$. Additionally, it was shown that the intensity was linearly increased up to 10% of the Eu concentration.

• 한국실내디자인학회논문집
• /
• 제16권6호
• /
• pp.144-151
• /
• 2007

The idea of shopping is changed from a purchase of merchandise to an experience of pleasure. This study is a space composition analysis for the introduction of theme in multi-plex shopping center design to reflect variable consumer trend and company marketing strategy, The study progressed through theoretical consideration and substance analysis about the shopping centers which had been designed by Jerd Partnership In Japan since 2000. The following is result. The path is a sole main street that is made of curve form, parallel and vertical circulating rout and movement of human being. It leads continuity. The node and landmarks have a circular court with typifier as powerful center, character of transition space and event for experience. It makes locational quality. The districts are composed of retail shops, restaurants and culture facilities and the edge is represented by closed vertical wall and parapet. It induces a domain. The characteristic of Jerde shopping center is an experience of theme environment through the path as betweenness with a story based on a main theme. It is mostly related nature or exotic element and is obviously represented at path and node. The node takes a round shape and bring about event as a court. The application of theme to the shopping center by Jerde has a significant meaning for place marketing.

• 한국산학기술학회논문지
• /
• 제8권5호
• /
• pp.1042-1046
• /
• 2007

본 연구에서는 제 3의 화학 원소 첨가에 의한 코발트 실리사이드와 니켈 실리사이드의 열적 안정성 향상 메카니즘을 조사하였다. 즉, Co-Si 시스템에 텅스텐을 첨가하는 경우 CoSi의 heat of formation이 증가하는 것으로 관찰되었다. 이러한 증가는 시스템 에너지 감속 속도의 최대화로 대변되는 실리사이드 형성 kinetics가 선호하는 glass의 형성을 억제하는 것으로 밝혀졌다. 이 경우 CoSi와 실리콘 기판 사이의 계면에 형성되는 다결정 구조는 glass의 self-diffusion보다 확산계수가 훨씬 작아 상 변이를 위해서는 보다 높은 열에너지를 요구하게 되어 궁극적으로 CoSi의 열적 안정성이 향상되는 것을 알 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.46-46
• /
• 2007

There has been rapid progress in the portable electronics industry. which has led to a great increase for a demand of portable, lightweight power sources. Lithium 2'nd batteries have met these demand. and many studies on the cahtod materials for the lithium 2,nd batteries have been reported during the last decade. Possible candidates for the cathode materials for lithium 2,nd batteries are $LiCoO_2$, $LiNiO_2$, and $LiMn_2O_4$. Currently $LiCoO_2$ is widely used. but $LiMn_2O_4$ is an excellent alternative material in view of its several advantages such a low cost as well as the wasy availability of raw materials and environmental benignity. In this study, find the most suitable synthesis method that satisfied high capacitor and stability cycle character, etc in Li-Mn oxide for 2'nd batteries. And also made an experiment on doping the $LiMn_2O_4$ spinel with a small amount of metal ions has a remarkable effect on the electrochemical properties and characterics of powder, BET, PSA, Porosity, etc.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.122-122
• /
• 2010

ZnO is a widely investigated material for the blue and ultraviolet solid-state emitters and detectors. It has been promoted due to a wide-band gap semiconductor which has large exciton binding energy of 60 meV, chemical stability and low radiation damage. However, there are many problems to be solved for the growth of p-type ZnO for practical device applications. Many researchers have made an efforts to achieve p-type conductivity using group-V element of N, P, As, and Sb. In this letter, we have studied the optical characteristics of the antimony-doped ZnO (ZnO:Sb) thin films by means of photoluminescence (PL), PL excitation, temperature-dependent PL, and time-resolved PL techniques. We observed donor-to-acceptor-pair transition at about 3.24 eV with its phonon replicas with a periodic spacing of about 72 meV in the PL spectra of antimony-doped ZnO (ZnO:Sb) thin films at 12 K. We also investigate thermal activation energy and carrier recombination lifetime for the samples. Our result reflects that the antimony doping can generate shallow acceptor states, leading to a good p-type conductivity in ZnO.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 추계학술대회 논문집
• /
• pp.17-22
• /
• 2008

Construction project have extremely high risk in the process of construction owing to unexpected event, like as design amendment. As a result, owner have to endure enormous extra-cost to control the risk and continue to the project having more higher uncertainty. Also, if the structure is completed, it is needed that the structure is protected and maintained continuously during life cycle time to satisfying original aim of structure itself. LCC analysis to calculate cost of structure alternatives divides into two stage, one is design_LCC and the other is maintenace_LCC. But two stages all is needed in the transition deterioration model to calculate more reasonable LCC analysis. This paper developed the model using analysis of FMS contents and survey from professional about Prestressed concrete beam girder bridge(PC Beam bridge)in railway. The model is focused in project level of PC beam because any condition state information for element level analysis can not get up. This paper is intended to use the developed model in LCC analysis of PC Beam bridge in railway and constitute the foundation to perform more deep study in the near future.

• 한국압력기기공학회 논문집
• /
• 제15권1호
• /
• pp.18-27
• /
• 2019

The Advanced Power Reactor 1400 (APR1400) Steam Generator (SG) uses alloy 690 as a tube material and SA-508 Grade 3 Class 1 as a tubesheet material to form tube-to-tubesheet joint through hydraulic expansion process. In this paper, the residual stresses in the SG tube-to-tubesheet contact area was investigated by applying Model-Based System Engineering (MBSE) methodology and the V-model. The use of MBSE transform system description into diagrams which clearly describe the logical interaction between functions hence minimizes the risk of ambiguity. A theoretical and Finite Element Methodology (FEM) was used to assess and compare the residual stresses in the tube-to-tubesheet contact area. Additionally, the axial strength of the tube to tubesheet joint based on the pull-out force against the contact joint force was evaluated and recommended optimum autofrettage pressure to minimize residual stresses in the transition zone given. A single U-tube hole and tubesheet with ligament thickness was taken as a single cylinder and plane strain condition was assumed. An iterative method was used in FEM simulation to find the limit autofrettage pressure at which pull-out force and contact force are of the same magnitude. The joint contact force was estimated to be 20 times more than the pull-out force and the limit autofrettage pressure was estimated to be 141.85MPa.