• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.916-919
• /
• 2004

The monopole theory has long been used to model air-pumped effect from the elastic cavities in car tire. This approach models the change of an air as a piston moving backward and forward on a spring and equates local air movements exactly with the volume changes of the system. Thus, the monopole theory has a restricted domain of applicability due to the usual assumption of a small amplitude acoustic wave equation and acoustic monopole theory. This paper describes an approach to predict the air-pumping noise of a car ave with CFD/Kirchhoff integral method. The type groove is simply modeled as piston-cavity-sliding door geometry and with the aid of CFD technique flow properties in the groove of rolling car tyre are acquired. And these unsteady flow data are used as a air-pumping source in the next Cm calculation of full tyre-road geometry. Acoustic far field is predicted from Kirchhoff integral method by using unsteady flow data in space and time, which is provided by the CFD calculation of full tyre-road domain. This approach can cover the non-linearity of acoustic monopole theory with the aid of using Non-linear governing equation in CFD calculation. The method proposed in this paper is applied to the prediction of air-pumping noise of modeled car tyre and the predicted results are qualitatively compared with the experimental data.

• International Journal of Highway Engineering
• /
• v.7 no.4 s.26
• /
• pp.125-140
• /
• 2005

This study suggests a suitable random transverse tining for reduction tire/road noise from concrete pavement. Through literature reviews, random transverse tining that can disperse the energy concentrated to the specific frequency was suggested using the LCG(linear congruential generators) algorithm. The spacing of tining from this study is applied to Daegu-Pohang express highway. For the purpose oi comparison, two other random tining sections were included that are research products from Chung-Ang university and Wisconsin DOT. In result of pass-by noise measurement by car, though designed section is superior to the others as noise reduction by reducing pitch noise, the effectiveness is not large. In case of traffic noise measurement, lower noise was observed at random transverse tining sections than uniformly transverse tining section, too. But there are seine differences between pass-by noise and traffic noise.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.4
• /
• pp.247-254
• /
• 2015

Ride comfort is one of the major factors in evaluating the performance of the vehicle. Tire is closely related to the ride comfort of the vehicle as the only parts in contact with the road surface directly. Vertical stiffness which is one of the parameters to evaluate the tire performance is great influence on the ride comfort. In general, the lower the vertical stiffness, the ride comfort is improved. Research for improving the ride comfort has been mainly carried out by optimizing the shape of the pneumatic tire. However, demand for safety of the vehicle has been increased recently such as a run-flat tire which is effective in safety improvement. But a run-flat tire have trouble in practical use because of poor ride comfort than general tire. Therefore, In this paper, the research was carried out for improving the ride comfort through the optimization of the SIR shape inside a run-flat tire. Meta-model was generated by using the design of experiment and it was able to reduce the time for the finite element analysis of optimization. In addition, Shape optimization for improving the ride comfort was performed by using the genetic algorithm which is one of the global optimization techniques.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.621-622
• /
• 2013

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.4
• /
• pp.381-389
• /
• 2010

Modern military equipments are often required to be mounted on a truck for their survivability and operation performance. Special units installed on the truck at times experience serious shock vibration caused by obstacles of road and/or uncommon road shape. It is then essential to analyze the travel performance of truck-mounted special units for their survivability and performance. In this paper, shock responses of the equipments subjected to bump passing and wash board road are experimentally obtained and also analyzed via FEM. Modified bump configuration and road profile considering the interface with tire are suggested. Analytical results considering this modification show good agreement with test results.

• International Journal of Highway Engineering
• /
• v.15 no.3
• /
• pp.31-36
• /
• 2013

PURPOSES: This study is to investigate a generated traffic noise when vehicle pass over a transverse rumble strip at toll plaza of highway. METHODS: To investigate traffic noise at toll plaza of highway, Pass-by method which is the most common used for measuring traffic noise was adopted and the traffic noise at toll plaza was measured for 10 min per hour for 11hours(13:00~24:00). RESULTS: The measured traffic noise by pass-by method was changed as function of the transverse rumble strip configuration. Generally, the maximum difference among three noise measurement sections was 7 dB(A). It might be related with traffic speed. Also, the measured traffic noise was strongly generated from a passenger car which was 2 axle. It means that the most of traffic noise on the road is generated at tire/pavement interface of the passenger car. CONCLUSIONS: The traffic noise was strongly related with vehicle speed and transverse rumble strip configuration on the road. For driver safety, the transverse rumble strip is definitely necessary. However, the complaints from residents near highway was increased by traffic noise from transverse rumble strip. Therefore, To satisfy both safety and reduction of traffic noise, the development of configuration of transverse rumble strip is necessary in the further study.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.5
• /
• pp.110-116
• /
• 2011

Water on a road surface can lower the coefficient of friction of vehicle tires and it involves lots of risks. One way to prevent water from staying is to cut many "rain grooves" into the edges of the pavement parallel. Such grooves, however, can exert unwanted side forces, particularly on passenger tires, which cause "Groove Wander" making the drivers uncomfortable. The "Groove Wander" is somewhat related to vehicle geometry, but is more strongly related to interaction between road grooves and tire tread's longitudinal grooves. This thesis tries to examine principles to estimate "Groove Wandering" effect focusing on the design of longitudinal groove. Additionally, it studied how to reduce pipe resonance longitudinal grooves form in the contact patch.

• International Journal of Highway Engineering
• /
• v.15 no.6
• /
• pp.61-68
• /
• 2013

PURPOSES : The purpose of this study is to study the noise reducing effect of Micro Surfacing by comparing general asphalt, longitudinal tining and Slurry Seal. METHODS : This study measures vehicles' noise of each section by the NCPX method that can measure noise between the road surface and the tire at the field. Total sound pressure and sound pressure level by the 1/3 octave band frequency are calculated through the field data of each section. Total sound pressure level is compared by ANOVA test statistically. After ANOVA test, post-hoc test is conducted to know mean difference of surface type by Tukey. RESULTS : As the result of CPB analysis to confirm sound pressure levels by frequency, it was shown that sound pressure levels by frequency are totally similar except for those of frequency bands between 100Hz and 500Hz. The result of ANOVA test and post-hoc test, it was shown that sections of surface type have a difference. The result of Micro Surfacing was lower 2~5dB(A) than other surface type. CONCLUSIONS : It is found that the noise reduction performance of Micro Surfacing was better than other surface type.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.2
• /
• pp.210-216
• /
• 2016

In this work, performance analysis to improve ride comfort of an ER (electrorheological) fluid damper for a mid-sized passenger vehicle in terms of tire pressure is presented. An ER damper by considering specification for a mid-sized commercial passenger vehicle is proposed and mechanically designed. After manufacturing and assembling the proposed ER damper with design parameters, their performance such as field-dependent damping forces are experimentally measured. A quarter-vehicle ER ECS (Electronic Control Suspension) system consisting of the ER damper, sprung mass, spring, sky-hook controller and tire is constructed to analysis the ride comfort performances. Vertical tire stiffness with different tire pressure is experimentally measured and investigated. In addition, ride comfort analysis such as vertical acceleration root mean square (RMS) of sprung mass is investigated under bump road using quarter-vehicle test equipment.

• The Journal of the Acoustical Society of Korea
• /
• v.14 no.5
• /
• pp.11-19
• /
• 1995

The Interaction between tire and road is responsible for the excited vibration of the tire, and It is also important for the sound radiation. In this paper. measurement of tire structural vibration noise from a chassis dynamometer using Spatial Transformation of Sound Field(STSF) technique is studied. STSF involving a scan that uses an array of transducers over a planar surface close to the source is under investigation. From cross spectra measurement during the scan, a principal component representing the sound field is extracted. Any power descriptor of the near field can then be investigated by means of near-field acoustic holography, while the distant field can be determined by application of Helmholtz integral equation. The results of the measurement were used to obtain the radiation sound pattern from the center line of the tire, and to locate the radiation sound generating regions in the vicinity of the tire.