• Journal of Chest Surgery
• /
• 제28권8호
• /
• pp.766-771
• /
• 1995

The trachea is defined as the airway from the inferior border of the cricoid cartilage to the top of the carinal spur. This paper would confirm the normal tracheal length of Korean adults through the actual measurement using the fiberoptic bronchoscopy. The subjects of this study were 25 patients, 13 males and 12 females between the age of 20 to 69 without abnormality on the neck, trachea, mediastinum and lung pharenchyme on the preoperative chest X-ray, who received the operations from the period of July to September, 1994. For those patients who had heart diseases, the cardiothoracic ratio was below 50%. The measurement was performed on the patients with endotracheal intubation under the general anesthesia in supine and neutral position. The tracheal length was calculated by the difference between the length from the tip of the endotracheal tube [E-tube to carina and to the needle which was inserted into the E-tube at the lower border of the palpated cricoid cartilage, by inserting the broncoscopy through the E-tube. The result was as follow : 1 The measured tracheal length for men was 11.8 0.2 cm[mean standard deviation and women was 10.5 0.3 cm, and that was longer than this [p<0.01 . The average was 11.2 1.0 cm and the standard error was 0.20 cm. 2 According to the correlation between the tracheal length to weight, height[Ht , age, and body surface area[BSA respectively, the Ht [p=0.003 , age [p=0.055 , and the BSA[p=0.017 were significant, while weight was not [p=0.314 . 3 From the regression analysis of the tracheal length[T.L. to the Ht, Age, and the BSA which were significant, the following equation was derived.i Ht : T.L.= -1.29 + 0.076 x Ht [P=0.003 ii Age: T.L.= 10.04 + 0.028 x Age [P=0.055 iii BSA : T.L.= 5.60 + 3.48 x BSA [P=0.017 iv In multi-regression : T.L. = -4.15 + 0.034 x Age + 0.085 x Ht [P=0.0002]

• The Korean Journal of Pain
• /
• 제14권2호
• /
• pp.193-198
• /
• 2001

Background: Anterior atlantoaxial subluxation (AAS) is a frequent phenomenon in rheumatoid arthritis (RA). AAS compresses the C2 ganglion or nerve and is a cause of posterior neck pain or occipital headache. Methods: We selected RA patients that had developed posterior neck pain or occipital headache caused by AAS. AAS was diagnosed by an increase of ADI (atlantodental interval). A distance of 3 mm or more was considered significant. Patients with vertical subluxation or symptoms suggestive of myelopathy were excluded. Before C2 RF ganglionotomy, we proceeded with a C2 ganglion block or greater occipital nerve block used by local anesthetics. For C2 RF ganglionotomy, the patient was placed in the supine position on a fluoroscopic table. A 100 mm, 4 mm active tip electrode was chosen. Following sensory stimulation at 0.2 to 0.6 V, the lesion was performed at a temperature of $60^{\circ}C$ to $65^{\circ}C$ for 60 sec. We followed up the patient after 6 months later. Results: All cases were female and the average duration of RA was 8.5 years. The duration of posterior neck pain or occipital headache was 1-8 months. The average ADI was 4.2 mm and the McGregor index was 3.3 mm on the average. In all cases, the score on the 4 point Likert scale was 4 (pain free) during the follow-up period. Conclusions: We found that the occipital headache or posterior neck pain caused by AAS in rheumatoid arthritis patients was alleviated over a short term follow up. C2 RF ganglionotomy is suggested as an effective palliative treatment for AAS in RA patients.

• Journal of Korean Neurosurgical Society
• /
• 제30권3호
• /
• pp.319-324
• /
• 2001

Objectives : The percutaneous vertebroplasty provides a good result in the treatment of osteoporotic vertebral compression fractures. But, the epidural leakage of polymethylmetacrylate(PMMA) after vertebroplasty may decrease the therapeutic effects because of the compression of thecal sac and/or nerve roots. The authors carried out a prospective study to evaluate the causative factors of epidural leakage of PMMA and to assess the influence on the outcome. Methods : This study involved 347 vertebral levels of compression fractures in 159 patients. Among these, the epidural leakages were identified in 92 vertebral levels(26.5%) in 64 patients(40.3%) on post-operative CT scan. Results : The incidence of epidural leakage of PMMA was significantly higher in the level above T7(p=0.001). The large amount of the injected PMMA and the use of an injector also increased the incidence(p=0.03 and p=0.045, respectively). The position of the needle tip in the vertebral body and the pattern of venous drainage did not influence. The immediate post-operative visual analogue scale(VAS) scores and facial scales(FS) were higher in the patients with epidural leakage(p=0.009). But there were no significant differences between the two groups after three months of operation(p=0.541). Conclusions : The incidence of epidural leakage of PMMA after percutaneous vertebroplasty appears to have relationship with the amount of PMMA and the levels injected. The epidural leakage of PMMA reduced the immediate therapeutic effects of vertebroplasty, but did not influence the late outcome. However, the epidural leakage should be avoided because of its potential neurological complications.

• 정보처리학회논문지B
• /
• 제16B권5호
• /
• pp.347-358
• /
• 2009

손동작을 인식하는 연구가 오랫동안 이뤄져 왔지만 대개의 시스템들이 값비싼 깊이 카메라를 사용하거나 여러 개의 카메라를 사용해 분석하는 등 그 비용이 크며 작동이 가능한 작업 공간이 지극히 제한적이었다. 본 논문에서는 가전제품을 원격 제어하기 위한 목적으로 두 개의 회전 모터를 사용해 작업 공간을 확대하고 저렴한 일반 카메라를 사용해서 효율적으로 손동작을 인식하기 위한 시스템을 제안한다. 이 시스템은 입력된 카메라의 자세 정보와 이미지상의 2차원적 손가락 위치 정보를 이용하여 3차원 궤적을 추정하고 이를 동작 평면으로 투영시켜 의미 있는 선형 동작 패턴으로 복원한다. 또한 본 논문에서는 개발된 시스템을 테스트하여 주어진 목적에 맞는 정확도를 가지는 작업 영역을 정의한다.

• 한국항공우주학회지
• /
• 제38권3호
• /
• pp.294-299
• /
• 2010

비상위치송수신장치(ELT)는 항공기 추락 시 조난 신호를 송출하는 장비이다. 유용한 장비이지만 항공기 추락과 경착륙에 대한 오판으로 인하여 잘못된 조난신호를 송출하기도 한다. 이러한 문제점은 현재 사용되고 있는 기계식 G-스위치의 부정확성에 그 원인이 있다. ELT의 성능 개선을 위하여 기계식 G-스위치를 MEMS 가속도계로 대체한 ELT 시스템을 개발하였다. ELT 시스템은 가속도 정보 수집/분석 시스템과 추락 판단 프로그램, 추락 상황에서 위치 정보를 제공하기 위한 GPS 수신 시스템으로 구성되어 있다. 또한, ELT 시스템을 검증하기 위한 자유 낙하 실험대를 제작하였다. 자유 낙하 실험대는 추락과 경착륙에 해당하는 충격 가속도와 충격 유지 시간을 모사할 수 있도록 설계하였다. 자유 낙하 실험대를 이용하여 개발한 ELT 시스템이 정확히 작동함을 확인하였다.

• 대한인간공학회:학술대회논문집
• /
• 대한인간공학회 1997년도 춘계학술대회논문집
• /
• pp.17-25
• /
• 1997

The evoked potentials for concentrations of solutions of the four qualities of tastes(i.e., sweet, salty, sour, and bitter tastes) were measured. The solution was applied to the chorda tympani nerve located on the left side of the tongue at 20mm from the tip and 15mm left from the center line. The evoked potentials were detected from Cz referred to A1(left lobe) with the ground at the Fpz position. The Maximum potential level and its latency were evaluated. The individual threshold level of concentration of the solutions of four tastes were measured. Artificial saliva was used as a control solution. The evoked positive potentials for four qualities of tastes (i.e., gustatory evokde potentials) were found to be around 150ms by averaging eight responses. The arbitrary concentration of the solutions were presented by the relative concentration, which was the ratio of the arbitrary concentration to the individual threshold level. The characteristic relations between the latency and the relative concentration ;and those between the potential level and the relative concentration were evaluated. These evalutions showed that (1) the latencies for salty and bitter tastes denoted the minimum values due to for the change of relative concentration, and that (2) the latency for sour taste decreased as the relative concentrations increased, while the latency for sweet taste denoted the inverse tendency, Sinificant differences between any two maximum potential levels were not recognized. A response latencies to sucrose were abolished after treatment of tongue by a sweet-suppressing agent.

• 대한치과보철학회지
• /
• 제37권5호
• /
• pp.607-619
• /
• 1999

Cortical support is an important factor, as the engagement of the fixture in strong compact bone offers an increased load-carrying capacity and initial stability. Because of the poor bone quality in the posterior mandible and other anatomic considerations, it has been suggested that implant fixtures be placed in these locations with apical engagement of the lingual cortical plate for so-called bicortication. The purpose of this investigation was to determine the effect of cortical engagements and in addition polyoxymethylene(POM) intramobile connector(IMC) of IMZ implant on implant load transfer in edentulous posterior segment of mandible, using three-dimensional (3D) finite element analysis models composed of cortical and trabecular bone involving single implant. Variables such as (1) the crestal peri-implant defect, (2) the apical engagement of lingual cortical plate, (3) the occlusal contact position (a vertical load at central fossa or buccal cusp tip), and (4) POM IMC were investigated. Stress patterns were compared and interfacial stresses along the bone-implant interface were monitored specially. Within the scope of this study, the following observations were made. 1) Offset load and angulation of fixture led to increase the local interfacial stresses. 2) Stresses were concentrated toward the cortical bones, but the crestal peri-implant defect increased the interfacial stresses in trabecular bone. 3) For the model with bicortication, it was noticed that the crestal cortical bone provided more resistance to the bending moment and the lingual cortical plate provided more support for the vertical load. But Angulation problem of the fixture from the lingual cortical engagement caused the local interfacial stress concentrations. 4) It was not clear that POM IMC had the effect on stress distribution under the present experimental conditions, especially for the cases of crestal peri-implant defect.

• 대한기계학회논문집B
• /
• 제36권2호
• /
• pp.117-123
• /
• 2012

본 연구에서는 벌지 실험과 나노 압입 실험을 통해 박막의 기계적 물성을 측정하였다. 벌지 실험은 외적 지지구조를 가지지 않는 박막 시편의 한 면에 일정한 압력을 가하여 박막의 변위를 측정, 압력과 변위의 관계를 이용하여 박막의 기계적 물성을 측정하는 실험이다. 나노 압입 실험은 시편에 압입 방향으로의 하중과 시편의 표면으로부터 압입자의 깊이에 대한 데이터를 통하여 시편의 기계적 물성을 측정하는 실험으로 modified King's model 을 이용하여 모재의 영향이 고려된 박막의 물성을 구할 수 있다. 두 실험은 탄성 계수와 푸아송비의 수학적 관계가 다르기 때문에 벌지 실험과 나노 압입 실험결과로부터 박막의 탄성계수와 푸아송비를 동시에 측정할 수 있다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.599-603
• /
• 2003

This paper present an error compensation system and On-Machine Measurement(OMM) system for improving the machining accuracy of ultra-precision lathe. The Fast-Tool-Servo(FTS) driven by a piezoelectric actuator is applied for error compensation system. The controller is implemented on the 32bit DSP for feedback control of piezoelectric actuator. The control system is designed to compensates three kinds of machining errors such as the straightness error of X-axis slide, the thermal growth error of the spindle. and the squareness between spindle and X-axis slide. OMM is preposed to measure the finished profile of workpiece on the machine-tool using capacitive sensor with highly accurate ruby tip probe guided by air bearing. The data acquisition system is linked to the CNC controller to get the position of each axis in real-time. Through the experiments, it is founded that the thermal growth of spindle and tile squareness error between spindle and X-axis slide influenced to machining error more than straightness error of X-axis slide in small travel length. These errors were simulated as a sinusoidal signal which has very low frequency and the FTS could compensate the signal less than 30 m. The implemented OMM system has been tested by measuring flat surface of 50 mm diameter and shows measurement error less than 400 mm

• 한국CDE학회논문집
• /
• 제13권6호
• /
• pp.403-411
• /
• 2008

The alignment of facial images is crucial for 2D face recognition. This is the same to facial meshes for 3D face recognition. Most of the 3D face recognition methods refer to 3D alignment but do not describe their approaches in details. In this paper, we focus on describing an automatic 3D alignment in viewpoint of quantitative analysis. This paper presents a framework of 3D face alignment and normalization based on feature points obtained by Active Shape Models (ASMs). The positions of eyes and mouth can give possibility of aligning the 3D face exactly in three-dimension space. The rotational transform on each axis is defined with respect to the reference position. In aligning process, the rotational transform converts an input 3D faces with large pose variations to the reference frontal view. The part of face is flopped from the aligned face using the sphere region centered at the nose tip of 3D face. The cropped face is shifted and brought into the frame with specified size for normalizing. Subsequently, the interpolation is carried to the face for sampling at equal interval and filling holes. The color interpolation is also carried at the same interval. The outputs are normalized 2D and 3D face which can be used for face recognition. Finally, we carry two sets of experiments to measure aligning errors and evaluate the performance of suggested process.