• Journal of Aerospace System Engineering
• /
• v.1 no.4
• /
• pp.42-45
• /
• 2007

The process of Lay-out design and assembly for liquid rocket engine was presented and the Lay-out design for main components of liquid Rocket engine system was studied. Vertical direction is recommended in the case of turbopump's arrangement. If the length of pipe between gas-generator with turbopump's turbine is shorter, gas-generator is stable. The arrangements of main valves are recommended as near disposition to combustion chamber, because shut-down process time is shorter. Interference with launch vehicle and structural strength considering gimbal actuator's force and control performance is considered in the case of gimbal actuator's supporter design.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.53 no.2
• /
• pp.94-102
• /
• 2004

The digital electronic switching system has some problems, when this system processes OAM(Operation, Administration And Maintenance) messages about the fault, the traffic, the account, and the performance, etc., at the present. One of these problems is that each the module processing these messages in the digital electronic switching system can not process OAM messages out of another digital electronic switching system. Each the module processing these OAM messages, that is, has been programmed in order to process only the OAM message out of the digital electronic switching system mounting itself, not to process the message out of the digital electronic switching system based on another platform. Therefore, we studied on methods that could process OAM messages out of all digital electronic switching systems and, first of all, developed the MGS(Message Gathering System) to be able to accept and process the fault message of OAM messages out of all digital electronic switching systems in real time.

• Journal of the Korean Society of Safety
• /
• v.25 no.1
• /
• pp.32-37
• /
• 2010

When back-out & firing Process applies heat, hume is piled up in exhaust duct by organic compound and it have high dangerousness. There by, the process is happening a lot of damage that is exhaust duct fire. However we do not have certain fire dangerousness estimation and digestion countermeasure. So we need preventive measure. Back-out & firing is a process which has fine structure, electrical and mechanical characteristics, such as firing kiln and back-out kiln which has pipe line and box type. The box oven is made of heating coil, fan motor and control panel. Back-out & firing process has air circulation institution of quick ventilation type. When we operate this process for long time, fire can break out easily. Duct is made by zinc shredder. If fire breaks out in duct inside, fire by deposit fume can be dispersed easily. Accordinglym, This project estimate danger for back-out & firing process exhaust duct through real fire test. And there is purpose of study to establish preventive measure.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.55 no.9
• /
• pp.401-408
• /
• 2006

In a multi-sensor multi-target tracking systems, the local sensors have the role of tracking the target and transferring the measurements to the fusion center. The measurements from the same target can arrive out of sequence called the out-of-sequence measurements(OOSMs). Out-of-sequence measurements can arise at the fusion center due to communication delay and varying preprocessing time for different sensor platforms. In general, the track fusion occurs to enhance the tracking performance of the sensors using the measurements from the sensors at the fusion center. The target informations can wive at the fusion center with the clutter informations in cluttered environment. In this paper, the OOSM update step with MPDA(Most Probable Data Association) is introduced and tested in several cases with the various clutter density through the Monte Carlo simulation. The performance of the MPDA with OOSM update step is compared with the existing NN, PDA, and PDA-AI for the air target tracking in cluttered and out-of-sequence measurement environment. Simulation results show that MPDA with the OOSM has compatible root mean square errors with out-of-sequence PDA-AI filter and the MPDA is sufficient to be used in out-of-sequence environment.

• Archives of Plastic Surgery
• /
• v.37 no.4
• /
• pp.461-464
• /
• 2010

Purpose: Blepharoptosis can result from either congenital or acquired causes. Blow out fracture or facial bone fracture including blow out fracture can be one of the causes. Authors experienced 3 cases of severe blepharoptosis after blow out fracture treated only with observation after reduction of associated fracture. Methods: Reconstruction of orbital wall was conducted on all cases diagnosed as blow out fracture using 3 dimensional computed tomography, and conservative treatment was done on accompanying severe blepharoptosis. Results: At the time of injury, all cases showed severe blepharoptosis requiring frontalis muscle transfer for correction. But blepharoptosis was recovered in an average of 18 weeks without any surgical procedure except reconstruction of orbital wall. Conclusion: Once Blepharoptosis occurred after blow out fracture, thorough evaluation must be done at first. If definitive cause of blepahroptisis cannot be found as authors' cases, injury of oculomotor nerve may result in blepharoptosis. So, as for blepharoptosis after blow out fracture, conservative treatment following reconstruction of fractured orbital wall can be one of good management.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.7
• /
• pp.1019-1023
• /
• 2014

The issue of safety insurance in PES(Programmable Electronic Systems) has been provoked because PES is difficult to define failure modes which are appeared in many different ways. But the PES applications extend rapidly in various areas. One of the solutions for PES safety insurance is voting which PES is used by comparing the outputs of several PES. The time synchronization of the PES is necessary for this reliable voting. The voting must be carried out with the outputs from same time inputs. There are several methods for time synchronization of the PES. In this paper, we discussed two modes of the time synchronization which are mutual synchronization of several PES and using UTC(Universal Time Clock).

• Journal of Welding and Joining
• /
• v.27 no.2
• /
• pp.57-62
• /
• 2009

This research was carried out to improve the productivity in the subassembly process of shipbuilding through optimal work planning for the shortest work time. The work time consist of welding time, moving time of gantry, teaching time of robot and robot motion time. The shortest work time is accomplished by even distribution of work and the shortest welding sequence. Even distribution of work was done by appling the simple algorithm. The shortest work sequence was determined by using GA. The optimal work planning decreased the total work time of the subassembly process by 4.1%. The result showed the effectiveness of the suggested simple algorithm for even distribution of work and GA for the shortest welding sequence.

• Journal of the Korean Chemical Society
• /
• v.6 no.2
• /
• pp.130-132
• /
• 1962

A new method of evaluating the mixing time in the continuous flow stirred tank is herein proposed. Experimental results to test the concept are also presented.The mixing time is defined as the time interval between the injection of a slug of an electrolyte solution into the tank and the moment at which an essentially straight line begins on a plot of the conductivity of effluent versus time.The proposed method of measuring the mixing time is valid even for the low mixing time (5 seconds) and the results obtained agree well with previous work, where the mixing time measurements were carried out by the injection of a dye into the feed stream.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.6
• /
• pp.23-32
• /
• 1996

This paper proposes a new buffer management scheme to service delay-sensitive traffic and loss-sensitive traffic fairly in ATM networks. The proposed scheme uses tow buffers for delay-sensitive traffic and loss-sensitive traffic. To satisfy the average delay time of delay-sensitive traffic, cells in real-time buffer are served first. When congestion occurs in nonreal-time buffer, low loss priority cell in real-time buffer can be pushed out by high loss priority cell in nonreal-time buffer can be transferred to real-time buffer considering threshold value in real-time buffer. Using computer simulation, the existing methods and proposed scheme are compared and analyzed with respect to cell loss rate and average delay time. Simulation results show that the proposed scheme have superior performance to conventional schemes.

• Proceedings of the KIEE Conference
• /
• 1995.07b
• /
• pp.922-924
• /
• 1995

The modeling of accurate timing in storage elements of ASIC cell library was studied. The propagation delay time of clock signal affects the critical time and this can cause malfunction in the chip designed in synchronous. In this paper, an analysis on the effect of input slope of clock signal in timing modeling were carried out. For the first time, in ASIC design, the design guides that can be used in both $0.6{\mu}M$ and $0.8{\mu}m$ design rule were offered, reducing the run time of SPICE and the time of cell library development.